Texas Instruments

OPA743PA - 12V, 7MHz CMOS RRIO Op Amp | Texas Instruments

MPN: OPA743PA ✓ فعال
12 V Vdss 1.1 mA Id 8-pin PDIP Package
حداقل سفارش: 1 |

OPA743PA نمای کلی

Texas Instruments OPA743PA is a single operational amplifier optimized for low-voltage, high-speed signal conditioning, featuring 7 MHz gain-bandwidth product, 10 V/µs slew rate, and rail-to-rail input and output operation in an 8-pin PDIP package. It operates from a single supply of up to 12 V or from dual supplies of ±6 V.

An operational amplifier is a voltage-gain component that compares its inverting and non-inverting inputs and drives its output according to the difference between them. Within the broader semiconductor hierarchy, the OPA743PA belongs to the CMOS operational-amplifier family, where it provides signal amplification, buffering, filtering, and level conversion for analog and mixed-signal systems. Its rail-to-rail input and output characteristics make it useful when signals approach the supply rails.

The device combines a 7 MHz gain-bandwidth product with a 10 V/µs slew rate, allowing it to process higher-frequency signals without requiring a bipolar operational amplifier. Typical quiescent current is 1.1 mA, helping limit power consumption in battery-powered and portable equipment. Full-scale common-mode rejection is specified at 84 dB, supporting rejection of common-mode noise in sensor, instrumentation, and industrial control circuits.

OPA743PA is implemented in CMOS technology and supports single-supply voltages up to 12 V, allowing operation from common 3.3 V, 5 V, and 12 V systems when the loop configuration and output-swing requirements permit. The manufacturer specifies the family over supply ranges extending to ±1.75 V through ±6 V for single and dual operation, providing flexibility across low-voltage instrumentation and higher-voltage analog interfaces.

Typical applications include sensor-signal conditioning, low-voltage data acquisition, audio and communication signal paths, LCD gamma-correction reference buffers, analog filters, and general-purpose buffering. The high output-current capability combined with 12 V operation makes the OPA743 particularly suitable for driving higher-capacitance loads and LCD reference networks when design limits are respected.

The primary design considerations are input common-mode range, output swing, load capacitance, and stability. Feedback-loop compensation should be checked for target gain and capacitive loading, while power-supply bypassing should be placed close to the supply pins. The manufacturer datasheet should be used to select operating points and confirm that signal amplitudes, load conditions, and package limits remain within specification.

This product page combines the OPA743PA family characteristics, package identification, application guidance, and practical design considerations into a concise engineering reference. It highlights the 7 MHz bandwidth, 10 V/µs slew rate, 84 dB common-mode rejection, rail-to-rail I/O operation, and 1.1 mA quiescent current that distinguish this general-purpose CMOS amplifier in practical analog-signal applications.

جایگزین‌های drop-in برای OPA743PA — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

OPA734PA

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
📦 8-pin PDIP
Same 12 V and 7 MHz headline specifications; detailed offset, noise, and bias-current differences are .

📋 جایگزین مرجع (خارج از کاتالوگ)

OPA735PA

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
📦 8-pin PDIP
Same 12 V and 7 MHz headline specifications; detailed offset, noise, and output-stage differences are .

📋 جایگزین مرجع (خارج از کاتالوگ)

OPA743PA حداکثر مقادیر مجاز و مشخصات الکتریکی

Number of Channels 1 channel
Maximum Supply Voltage 12 V
Single-Supply Operating Range Up to 12 V
Dual-Supply Operating Range ±6 V
Gain-Bandwidth Product 7 MHz
Slew Rate 10 V/µs
جریان سکون 1.1 mA
Common-Mode Rejection Ratio 84 dB
Input Type Rail-to-rail
نوع خروجی Rail-to-rail
Process Technology CMOS
تعداد پین‌ها 8 pins
بسته‌بندی 8-pin PDIP
نوع نصب Through-hole
Product Type Single CMOS operational amplifier

پیکربندی پین OPA743PA

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
پین 1 NC — Not connected
پین 2 IN- — Inverting input
پین 3 IN+ — Non-inverting input
پین 4 V- — Negative supply connection
پین 5 NC — Not connected
پین 6 OUT — Operational-amplifier output
پین 7 V+ — Positive supply connection
پین 8 NC — Not connected

کاربردهای معمول

OPA743PA مناسب است برای 6 کاربردs: Sensor Signal Conditioning, Low-Voltage Data Acquisition, LCD Gamma-Correction Reference Buffer, Portable Analog Front End, Active Audio Signal Conditioning, Industrial Control Signal Buffer.

🧩

Sensor Signal Conditioning

OPA743PA fits sensor-conditioning stages that require signal amplification close to the supply rails. Its rail-to-rail input operation accepts a broad input range, while the 7 MHz gain-bandwidth product and 10 V/µs slew rate preserve useful bandwidth for moderately fast sensor signals. The 1.1 mA quiescent current also limits overhead in portable or distributed measurement systems. Configure the feedback network for the required closed-loop gain, verify common-mode rejection at the operating frequency, and place supply bypassing close to the device.

📊

Low-Voltage Data Acquisition

OPA743PA is suitable for analog front ends in low-voltage data-acquisition equipment where both source impedance and signal bandwidth matter. Its CMOS implementation, 1.1 mA quiescent current, and 7 MHz gain-bandwidth product support low-power acquisition channels. The 84 dB common-mode rejection characteristic helps reduce unwanted common-mode signals in sensor and instrumentation systems. Select feedback components for the intended noise gain, check settling requirements for the acquisition bandwidth, and use short analog traces with a direct return path.

📺

LCD Gamma-Correction Reference Buffer

OPA743PA is specifically suited to LCD gamma-correction reference buffering because the manufacturer highlights the combination of 12 V operation, high output-current capability, 7 MHz bandwidth, and 10 V/µs slew rate for this use. Rail-to-rail output operation can provide useful voltage range in reference networks, while the fast slew rate helps reproduce changing correction waveforms. Confirm the panel's channel count and reference impedance, evaluate capacitive loading, and verify that the required output-voltage and current levels remain within the amplifier's limits.

📱

Portable Analog Front End

OPA743PA supports portable analog front ends where a 1.1 mA quiescent current is attractive but 7 MHz bandwidth and 10 V/µs slew rate are still useful. It can buffer sensors, implement active filters, or amplify low-level signals within systems powered from 3.3 V, 5 V, or other compatible supplies. The rail-to-rail input and output characteristics improve utilization of the available supply voltage. Designers should still account for output-swing limits, shutdown requirements, noise, and startup behavior when defining the complete low-power signal chain.

🎧

Active Audio Signal Conditioning

OPA743PA can amplify and buffer audio-frequency signals when the circuit requires more bandwidth than a general-purpose micropower amplifier. Its 7 MHz gain-bandwidth product and 10 V/µs slew rate support moderate audio-bandwidth and waveform demands, while the 1.1 mA quiescent current suits low-power audio equipment. A rail-to-rail output can increase signal range in a limited-voltage system. Confirm the required output swing, load impedance, channel count, distortion expectations, and stability with the selected feedback network.

🏭

Industrial Control Signal Buffer

OPA743PA is appropriate for buffering and scaling control signals in industrial systems requiring wider bandwidth than slow precision amplifiers. The 84 dB common-mode rejection ratio helps reject common-mode noise, while 1.1 mA quiescent current supports compact multi-channel designs. Its rail-to-rail input characteristic is useful when actuator or sensor signals span much of the available supply range. Verify noise immunity, output-current demand, temperature limits, and isolation requirements at the system level before using it in safety-critical control paths.

خلاصه محصولات پیشنهادی

OPA2743 Dual-member of the same OPA743 CMOS operational-amplifier family استفاده‌شده در: Sensor Signal Conditioning, Low-Voltage Data Acquisition, LCD Gamma-Correction Reference Buffer, Portable Analog Front End, Active Audio Signal Conditioning, Industrial Control Signal Buffer OPA4743 Quad-member of the same OPA743 CMOS operational-amplifier family استفاده‌شده در: Sensor Signal Conditioning, Low-Voltage Data Acquisition, LCD Gamma-Correction Reference Buffer, Portable Analog Front End, Active Audio Signal Conditioning, Industrial Control Signal Buffer
What is the operating voltage range of OPA743PA?
The OPA743PA operates from a single supply of up to 12 V or from dual supplies of ±6 V. According to the Texas Instruments OPA743 datasheet, the OPA743 family is specified and tested over supply ranges extending to ±1.75 V through ±6 V. The actual usable voltage depends on the common-mode input range, output swing, and power-supply requirements of the circuit. OPA743PA is the 8-pin PDIP ordering option of the single amplifier.
What are the key specifications of OPA743PA that engineers should know?
OPA743PA is a single 12 V, 7 MHz CMOS operational amplifier with rail-to-rail input and output, a 10 V/µs slew rate, 1.1 mA quiescent current, and 84 dB full-scale common-mode rejection. According to the Texas Instruments OPA743 datasheet, these characteristics place it between general-purpose low-power amplifiers and higher-speed signal-chain devices. The 8-pin PDIP package supports through-hole assembly and conventional prototyping.
Is OPA743PA a rail-to-rail operational amplifier?
Yes, OPA743PA provides rail-to-rail input and output operation. According to the Texas Instruments OPA743 datasheet, this allows the amplifier to accept input signals close to the supply rails and produce output voltage closer to the output limits than a conventional fixed-range amplifier. Rail-to-rail operation does not eliminate output-swing limits, so load current, output voltage, and supply voltage must still be checked against the electrical characteristics.
What is the gain-bandwidth product of OPA743PA?
OPA743PA has a 7 MHz gain-bandwidth product. According to the Texas Instruments OPA743 datasheet, this bandwidth supports closed-loop operation at frequencies determined by the selected noise-gain configuration and stability requirements. At higher closed-loop gains, the usable bandwidth is lower. The accompanying 10 V/µs slew rate helps the amplifier reproduce large-amplitude signals without excessive slew-rate distortion.
Where can I download the OPA743PA datasheet PDF?
The official OPA743PA datasheet is available from the Texas Instruments OPA743 product page and the linked OPA743 family datasheet. According to the manufacturer documentation, the document covers the OPA743, OPA2743, and OPA4743 single, dual, and quad CMOS operational amplifiers. Download the PDF from the official Texas Instruments link on this page and use its pin-description and electrical-characteristics tables for final design verification.
Where can I find the OPA743PA pinout?
The OPA743PA pinout is documented in the pin-configuration section of the Texas Instruments OPA743 family datasheet. It uses the conventional single-op-amp 8-pin PDIP arrangement shown in the package diagram on this page: pins 2 and 3 are the inverting and non-inverting inputs, pin 6 is the output, pin 7 is the positive supply, pin 4 is the negative supply, and pins 1, 5, and 8 are no-connect.
What can replace OPA743PA?
OPA743PA does not have a broadly documented set of pin-compatible 8-pin PDIP replacements with verified electrical characteristics. The available cross-reference material identifies related operational-amplifier options, but it does not establish five drop-in replacements with matching rail-to-rail I/O performance, bandwidth, supply range, and pin arrangement. Treat any substitution as a design-review candidate and verify the footprint and full operating limits in the original manufacturer datasheet.
Is OPA743PA the same as OPA743PAG4?
No, OPA743PA and OPA743PAG4 are not direct package-identical alternatives for a drop-in PCB replacement. According to distributor package listings, OPA743PA is an 8-pin PDIP device, while OPA743PAG4 is an 8-pin SOIC device. Their electrical functions are closely related, but the physical footprints and lead geometry differ, so a PCB redesign is required.
When should I choose OPA743PA over a lower-speed operational amplifier?
Choose OPA743PA when the signal path benefits from a 7 MHz gain-bandwidth product and 10 V/µs slew rate while retaining low 1.1 mA quiescent current. According to the Texas Instruments OPA743 datasheet, these characteristics suit sensor conditioning, buffering, filtering, and general-purpose analog signal processing. A lower-speed amplifier may be preferable when bandwidth and slew performance are unnecessary, but it will generally provide less headroom for faster or larger-amplitude signals.
When should I choose OPA743PA over a higher-power output amplifier?
Choose OPA743PA for compact, low-power analog stages that require rail-to-rail input and output operation rather than substantial load-current capability. The manufacturer identifies a 10 V/µs slew rate and notes the family's ability to drive high output currents, but OPA743PA is still a general-purpose CMOS operational amplifier. For sustained heavy loads, low distortion at high frequencies, or wide output swing into demanding loads, verify the output-current and thermal limits before committing.
Is OPA743PA suitable for LCD gamma-correction reference buffering?
Yes, OPA743PA is suitable for LCD gamma-correction reference buffering when the operating conditions fit the device limits. According to the Texas Instruments OPA743 family datasheet, the combination of 12 V operation, 7 MHz bandwidth, 10 V/µs slew rate, and high output-current capability is particularly useful for this application. Confirm the required reference voltage, channel bandwidth, capacitive loading, and output-current profile for the specific panel.
How should I design the power bypassing for OPA743PA?
Place the supply bypass capacitor and ground return as close as practical to the OPA743PA supply pins, with the shortest and lowest-inductance path possible. According to the Texas Instruments OPA743 datasheet application guidance, sound bypassing reduces supply impedance at high frequencies and helps prevent supply noise from appearing as output disturbance. Use a stable, low-ESR capacitor compatible with the required transient current, and avoid placing sensitive analog returns behind long shared paths.
How much power does OPA743PA dissipate?
OPA743PA dissipation depends on supply voltage, quiescent current, load current, and output voltage. Estimated from the manufacturer specifications of 1.1 mA quiescent current: at a 12 V supply, quiescent dissipation is approximately 13.2 mW before load-current effects are included. The estimate uses 12 V and 1.1 mA and does not replace the datasheet power ratings or application-specific thermal calculations.
Where can I buy OPA743PA online?
Use the Request a Quote form on this page to request OPA743PA pricing, current inventory status, minimum order quantity, and lead time. The form provides a direct purchasing channel for the exact Texas Instruments OPA743PA ordering option, an 8-pin PDIP single amplifier. Avoid substituting an OPA743UA, OPA743PAG4, or another package code without reviewing the footprint and ordering requirements.
What is the price of OPA743PA?
The current OPA743PA price is best obtained through the Request a Quote form on this page. The form can confirm pricing for the exact MPN, quantity breaks, order acceptance, and any applicable source-and-destination charges. Keep the requested package designation at OPA743PA because other OPA743 order codes can use a different package and therefore a different PCB footprint.
What is the lead time and stock status for OPA743PA?
Request the current OPA743PA stock status, lead time, and minimum order quantity through the Request a Quote form on this page. Lead time can vary with order quantity, package choice, and manufacturing conditions, so confirm the date applicable to your production schedule when submitting the request. Use the full manufacturer part number OPA743PA and the 8-pin PDIP package designation to avoid ambiguity.

داده‌های مرجع مهندسی برای OPA743PA — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose OPA743PA when the design requires a single, low-power CMOS operational amplifier with rail-to-rail input and output, 7 MHz bandwidth, and 10 V/µs slew rate. It is especially suitable for sensor conditioning, low-voltage data acquisition, LCD reference buffering, and general-purpose analog signal paths. A lower-bandwidth micropower amplifier may be preferable when speed and slew rate are unnecessary, while a dedicated high-current output amplifier is a better choice for heavy or capacitive loads. OPA743PA is supplied in an 8-pin PDIP package, so verify that its through-hole footprint matches the PCB. OPA743PAG4 offers a related electrical function in an 8-pin SOIC package but is not a direct drop-in replacement without a board change. No additional same-package drop-in alternatives with sufficiently documented pin and parametric equivalence were identified, so any proposed substitute should undergo a full footprint, supply, input-range, output-swing, stability, and load-capacitance review.

مقایسه با جایگزین‌ها

پارامتر این محصول
Brand Texas Instruments
Package 8-pin PDIP
Channel Count 1 channel
Maximum Single Supply 12 V
Maximum Dual Supply ±6 V
Gain-Bandwidth Product 7 MHz
Slew Rate 10 V/µs
Quiescent Current 1.1 mA
Common-Mode Rejection Ratio 84 dB
Input and Output Rail-to-rail
Technology CMOS

تفاوت‌های کلیدی

  • Combines moderate speed with low quiescent current (در مقابلLower-speed general-purpose CMOS operational amplifiers)
  • Uses rail-to-rail input and output operation (در مقابلConventional fixed-common-mode operational amplifiers)
  • Offers 84 dB common-mode rejection (در مقابلLow-cost amplifiers with unspecified CMRR)

یادداشت‌های طراحی

Place the supply bypass capacitor and analog return connection as close as practical to the OPA743PA pins. Keep the high-frequency return path short and avoid routing sensitive input traces beside digital, switching, or power-conversion nets. The 7 MHz gain-bandwidth product means that even short PCB traces can become electrically significant at the upper operating frequencies, so use a compact layout and a solid ground plane when the amplifier is part of a mixed-signal board.

Do not treat rail-to-rail input and output as unlimited ranges. Verify the input common-mode limits, output swing, load current, and supply limits at the intended temperature. In particular, a 10 V/µs slew-rate rating does not guarantee low distortion for every large-amplitude waveform. Check the closed-loop gain, output amplitude, load, and compensation requirements together so that the selected OPA743PA configuration remains stable and accurate.

Estimated: OPA743PA quiescent power is approximately 13.2 mW when operated from a 12 V supply, calculated as 12 V multiplied by the specified 1.1 mA quiescent current. This estimate excludes output-stage dissipation caused by load current and voltage drop. Use the manufacturer datasheet for complete power-rating limits, and include regulator efficiency, amplifier dissipation, and temperature rise when designing a compact power system.

Select feedback resistors and capacitors for the intended closed-loop bandwidth rather than relying only on the 7 MHz gain-bandwidth product. Capacitive loading can reduce stability and alter the effective bandwidth, so use an isolation resistor near the output if the load is capacitive. For sensor inputs, account for source impedance, bias-current error, and common-mode range at the slowest and fastest input conditions.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

No explicit compliance declarations for the OPA743PA ordering option were identified in the product and distributor results.

تاریخ تأیید داده‌ها: 2026-11-09 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

OPA743PA datasheet OPA743PA pinout OPA743PA datasheet pdf OPA743PA specifications OPA743PA 8-PDIP OPA743PA equivalent OPA743PA replacement OPA743PA cross reference OPA743PA vs OPA743PAG4 OPA743PA application circuit Texas Instruments OPA743PA OPA743PA price OPA743PA stock

قطعات و اصطلاحات مرتبط

Texas Instruments OPA743PA OPA743 OPA2743 OPA4743 operational amplifier CMOS operational amplifier voltage amplifier analog signal conditioning rail-to-rail input rail-to-rail output gain-bandwidth product slew rate quiescent current common-mode rejection ratio CMRR single-supply operation dual-supply operation LCD gamma correction reference buffer data acquisition sensor conditioning 8-pin PDIP DIP package through-hole package RoHS REACH
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ