SN74HC365D - 6-Bit 3-State Buffer | Texas Instruments
N.º de pieza: SN74HC365D ✓ ActivoSN74HC365D Descripción general
A hex buffer and line driver is a digital logic IC that strengthens signals for transmission between circuit sections or loads. The 74HC365 belongs to the high-speed CMOS logic family, which combines low static power consumption with CMOS-compatible input thresholds. Its buffer function preserves logic polarity while increasing drive capability for bus-oriented receivers, memory address drivers, and clock-distribution networks. The 3-state outputs allow multiple devices to share a bus without creating contention when a driver is disabled.
The SN74HC365D is identified as a non-inverting one-element, six-bit-per-element buffer with 3-state outputs in a 16-SOIC package. Its two output-enable inputs provide a common way to place all six outputs into high impedance, which simplifies shared-bus control. Because the enable inputs use overbar notation in the device description, their active state is low: pulling either enable input low permits normal output operation, while driving either input high disables the outputs.
Texas Instruments positions the SN74HC365 for memory-address driving, clock driving, bus-oriented receivers, and transmitters. The six channels operate from the same supply, allowing a complete six-bit section of a bus to be enabled or disabled together. The HC-series 2 V to 6 V supply range supports 5 V systems as well as compatible lower-voltage CMOS logic environments. Exact propagation-delay, output-current, and absolute-maximum ratings should be taken from the manufacturer datasheet for the specific revision and operating conditions.
Typical uses include microprocessor and microcontroller bus buffering, memory address-line isolation, clock fan-out, test-equipment interface isolation, and control systems where several data lines must connect conditionally to a shared resource. Two enable inputs provide bus-level arbitration without requiring individual gate control for every channel. The non-inverting configuration avoids inversion, making it suitable where source and destination logic use the same active-high or active-low interpretation.
PCB layout should place the device close to the source of the buffered signals and provide a short, low-inductance return path for every supply connection. Decoupling should follow the manufacturer recommendations, and unused inputs must not be left floating. Because the outputs can enter a high-impedance state, verify that downstream receivers tolerate the resulting bus level and that enable control remains stable during mode transitions.
This page combines manufacturer functional information, package details, sourcing context, pin-compatible alternatives, application guidance, and design checks in one engineering-focused reference. It is intended to accelerate schematic review and PCB replacement decisions while keeping the final design anchored to the official SN74HC365 documentation.
Alternativas directas para SN74HC365D — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
CD74HC365M
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
74HC365D,653
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
MC74HC365ADG
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
74HCT365D
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
74LVC365AD
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
SN74HC365D Valores máximos y características eléctricas
| Product Type | Hex non-inverting buffer/line driver |
| Number of Elements | 1 element |
| Bits per Element | 6 bits |
| Number of Channels | 6 channels |
| Tipo de salida | 3-state non-inverting output |
| Supply Voltage Range | 2 V to 6 V |
| Output Enable Inputs | 2 shared inputs |
| Disabled Output State | High impedance when either output-enable input is high |
| Encapsulado | 16-SOIC |
| Tipo de montaje | Surface mount |
| Logic Family | 74HC CMOS |
| Input Logic Level | CMOS-compatible |
Guía de configuración de pines de SN74HC365D 16-soic
Configuración de pines para SN74HC365D (encapsulado 16-soic). Este CI digital incluye GPIO, interfaces de comunicación (UART, SPI, I2C) y pines de alimentación. Consulte la hoja de datos del fabricante para conocer las funciones alternativas de los pines y las opciones de configuración. Esencial para el diseño de sistemas embebidos y el diseño de PCB.
No hay datos detallados de patillaje disponibles para SN74HC365D.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
SN74HC365D es adecuado para 6 aplicacións: Memory Address-Line Buffering, Clock Distribution and Fan-Out, Microprocessor Bus Isolation, Test and Measurement Interface Isolation, Embedded Control Data Fan-Out, Shared Peripheral Bus Isolation.
Memory Address-Line Buffering
The SN74HC365D is suitable for buffering six memory-address lines because it provides six non-inverting channels while allowing the complete address group to be disconnected when the bus is not owned. Texas Instruments identifies memory-address drivers as a primary use for the 74HC365 family. Its two shared output-enable inputs can place all six outputs in high impedance, reducing contention during memory-bus handshakes. The 2 V to 6 V supply range supports 5 V systems and compatible lower-voltage CMOS designs. During schematic review, confirm propagation delay and output-current limits against the system clock and load capacitance because these figures depend on supply voltage and operating conditions.
Recomendado
Clock Distribution and Fan-Out
The six-channel SN74HC365D can distribute one clock to several destinations while preserving polarity and adding buffering between the source and loads. Its independent data inputs permit multiple clock or control signals to be routed through one package, and the shared tri-state control can isolate the entire group from a shared line. The manufacturer identifies clock drivers as a target application. Keep trace lengths and return paths controlled so clock edges remain clean at the receiver, and verify the worst-case propagation delay from the datasheet when the clock period is short. The 16-SOIC format also allows compact placement near the driven logic.
Recomendado
Microprocessor Bus Isolation
The SN74HC365D fits bus-isolation points where six processor or peripheral lines must drive shared circuitry only during a defined ownership interval. The non-inverting buffers retain the original logic state, while the two output-enable inputs provide a common way to release all six outputs. This arrangement helps prevent bus contention in systems that combine a processor, memory, and peripheral devices. Texas Instruments specifically describes the family for bus-oriented receivers and transmitters. The design should define enable timing with the bus controller and confirm that downstream receivers maintain valid levels during high-impedance intervals. Supply decoupling and short ground returns are essential for clean switching behavior.
Recomendado
Test and Measurement Interface Isolation
The SN74HC365D can buffer six instrumentation signals between a test fixture and a shared measurement or switching network. Buffering reduces loading on the originating circuit, and the 3-state outputs allow the fixture to release the lines when another instrument or termination must take control. The six non-inverting channels make it suitable for parallel status, control, or address lines rather than differential high-speed signals. Because the device operates from 2 V to 6 V, select interface levels that remain within the family limits and validate propagation delay for the measurement timing budget. High-impedance behavior must be considered by the receiving circuitry, which should not depend on the disabled driver maintaining a defined voltage.
Recomendado
Embedded Control Data Fan-Out
The SN74HC365D can distribute six control or status lines from an embedded controller to distant modules while preserving logic polarity and strengthening the source outputs. The 16-SOIC package is convenient for routing across a compact control board, and the 2 V to 6 V operating range supports compatible embedded logic rails. When several modules share a communication line, the common output-enable function can disconnect the SN74HC365D group while another buffer owns the bus. Design the firmware or hardware arbiter to avoid overlapping enable windows, and check timing at the slowest specified supply voltage if the controller relies on a fixed setup or hold margin.
Recomendado
Shared Peripheral Bus Isolation
The SN74HC365D is appropriate for placing a six-line peripheral group behind a tri-state interface on a shared bus. High impedance releases the peripheral segment when it is not selected, while the non-inverting channels preserve the command and status logic presented to the active controller. The dual output-enable arrangement provides a common disable mechanism for all six lines, reducing the number of control signals required on a crowded board. Texas Instruments identifies bus-oriented receivers and transmitters as intended uses. The implementation must ensure only one driver enables at a time, provide a defined state for the shared bus when every driver is disabled, and validate propagation delay against the peripheral interface timing.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para SN74HC365D — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | CD74HC365M | 74HC365D,653 | MC74HC365ADG | 74HCT365D | 74LVC365AD |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SO | 16-SO | 16-SO | 16-SO |
| Brand | Texas Instruments | Texas Instruments | Nexperia | onsemi | Nexperia | Nexperia |
| Function | Hex non-inverting 3-state buffer/line driver | Hex 3-state buffer/line driver | Hex non-inverting 3-state buffer/line driver | Hex 3-state buffer/line driver | Hex 3-state buffer/line driver with TTL-compatible inputs | Hex 3-state buffer/line driver |
| Number of Channels | 6 | 6 | 6 | 6 | 6 | 6 |
| Output Enable Control | 2 shared output-enable inputs | 2 shared output-enable inputs | 2 shared output-enable inputs | 2 shared output-enable inputs | 2 shared output-enable inputs | 2 shared output-enable inputs |
| Input Threshold Type | CMOS-compatible HC input | CMOS-compatible HC input | CMOS-compatible HC input | CMOS-compatible HC input | TTL-compatible HCT input | CMOS-compatible LVC input |
| Disabled Output State | High impedance | High impedance | High impedance | High impedance | High impedance | High impedance |
| Polarity | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting |
Diferenciadores clave
- Six non-inverting channels can be disabled as one group (frente a MC74HC365ADG)
- Direct 74HC365-family interface compatibility (frente a 74HC365D,653)
- TTL-compatible replacement requires a different input-threshold choice (frente a 74HCT365D)
Notas de diseño
Use the SN74HC365D as a buffer between a source and a shared bus rather than as an active bus terminator. Keep the device close to the driven receiver when propagation delay or edge-rate control is important. Provide a continuous ground reference and route output-enable traces away from fast clock and data paths. Because all six outputs share the two enable controls, a switching enable can affect every channel simultaneously and should be sequenced to prevent contention.
Place the decoupling capacitor close to the device supply and ground pins, and avoid routing output-enable signals beneath or immediately beside high-speed clock nets. The 16-SOIC footprint requires adequate lead spacing for assembly and inspection. Preserve a direct ground return for every output branch; long or shared return paths can produce unequal edge timing between channels even when the logic function itself is correct.
Do not treat a high-impedance output as a driven logic zero or one. The downstream bus must have an appropriate pull-up, pull-down, or other defined state whenever every driver is disabled. Also verify the active-low enable polarity before layout because driving an enable input to the wrong state can release the outputs unexpectedly. Do not leave unused digital inputs floating, and confirm all timing and current limits from the manufacturer datasheet.
Información de cumplimiento
Use the current Texas Instruments product page and material-declaration documentation to confirm environmental, automotive, lead-free, halogen-free, and conflict-minerals status for the exact orderable MPN.