SN74HC365D - 6-Bit 3-State Buffer | Texas Instruments
MPN: SN74HC365D ✓ 啟用中SN74HC365D 概覽
A hex buffer and line driver is a digital logic IC that strengthens signals for transmission between circuit sections or loads. The 74HC365 belongs to the high-speed CMOS logic family, which combines low static power consumption with CMOS-compatible input thresholds. Its buffer function preserves logic polarity while increasing drive capability for bus-oriented receivers, memory address drivers, and clock-distribution networks. The 3-state outputs allow multiple devices to share a bus without creating contention when a driver is disabled.
The SN74HC365D is identified as a non-inverting one-element, six-bit-per-element buffer with 3-state outputs in a 16-SOIC package. Its two output-enable inputs provide a common way to place all six outputs into high impedance, which simplifies shared-bus control. Because the enable inputs use overbar notation in the device description, their active state is low: pulling either enable input low permits normal output operation, while driving either input high disables the outputs.
Texas Instruments positions the SN74HC365 for memory-address driving, clock driving, bus-oriented receivers, and transmitters. The six channels operate from the same supply, allowing a complete six-bit section of a bus to be enabled or disabled together. The HC-series 2 V to 6 V supply range supports 5 V systems as well as compatible lower-voltage CMOS logic environments. Exact propagation-delay, output-current, and absolute-maximum ratings should be taken from the manufacturer datasheet for the specific revision and operating conditions.
Typical uses include microprocessor and microcontroller bus buffering, memory address-line isolation, clock fan-out, test-equipment interface isolation, and control systems where several data lines must connect conditionally to a shared resource. Two enable inputs provide bus-level arbitration without requiring individual gate control for every channel. The non-inverting configuration avoids inversion, making it suitable where source and destination logic use the same active-high or active-low interpretation.
PCB layout should place the device close to the source of the buffered signals and provide a short, low-inductance return path for every supply connection. Decoupling should follow the manufacturer recommendations, and unused inputs must not be left floating. Because the outputs can enter a high-impedance state, verify that downstream receivers tolerate the resulting bus level and that enable control remains stable during mode transitions.
This page combines manufacturer functional information, package details, sourcing context, pin-compatible alternatives, application guidance, and design checks in one engineering-focused reference. It is intended to accelerate schematic review and PCB replacement decisions while keeping the final design anchored to the official SN74HC365 documentation.
直接替換替代品,適用於 SN74HC365D — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
CD74HC365M
✅ 直接替換📋 參考替代品(不在目錄中)
74HC365D,653
✅ 直接替換📋 參考替代品(不在目錄中)
MC74HC365ADG
✅ 直接替換📋 參考替代品(不在目錄中)
74HCT365D
✅ 直接替換📋 參考替代品(不在目錄中)
74LVC365AD
✅ 直接替換📋 參考替代品(不在目錄中)
SN74HC365D 最大額定值與電氣特性
| Product Type | Hex non-inverting buffer/line driver |
| Number of Elements | 1 element |
| Bits per Element | 6 bits |
| Number of Channels | 6 channels |
| 輸出類型 | 3-state non-inverting output |
| Supply Voltage Range | 2 V to 6 V |
| Output Enable Inputs | 2 shared inputs |
| Disabled Output State | High impedance when either output-enable input is high |
| 封裝 | 16-SOIC |
| 安裝類型 | Surface mount |
| Logic Family | 74HC CMOS |
| Input Logic Level | CMOS-compatible |
SN74HC365D 16-soic 腳位配置指南
SN74HC365D(16-soic 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: SN74HC365D.
請參閱 資料表 以查看完整腳位配置。
典型應用
SN74HC365D 適用於 6 應用s: Memory Address-Line Buffering, Clock Distribution and Fan-Out, Microprocessor Bus Isolation, Test and Measurement Interface Isolation, Embedded Control Data Fan-Out, Shared Peripheral Bus Isolation.
Memory Address-Line Buffering
The SN74HC365D is suitable for buffering six memory-address lines because it provides six non-inverting channels while allowing the complete address group to be disconnected when the bus is not owned. Texas Instruments identifies memory-address drivers as a primary use for the 74HC365 family. Its two shared output-enable inputs can place all six outputs in high impedance, reducing contention during memory-bus handshakes. The 2 V to 6 V supply range supports 5 V systems and compatible lower-voltage CMOS designs. During schematic review, confirm propagation delay and output-current limits against the system clock and load capacitance because these figures depend on supply voltage and operating conditions.
推薦
Clock Distribution and Fan-Out
The six-channel SN74HC365D can distribute one clock to several destinations while preserving polarity and adding buffering between the source and loads. Its independent data inputs permit multiple clock or control signals to be routed through one package, and the shared tri-state control can isolate the entire group from a shared line. The manufacturer identifies clock drivers as a target application. Keep trace lengths and return paths controlled so clock edges remain clean at the receiver, and verify the worst-case propagation delay from the datasheet when the clock period is short. The 16-SOIC format also allows compact placement near the driven logic.
推薦
Microprocessor Bus Isolation
The SN74HC365D fits bus-isolation points where six processor or peripheral lines must drive shared circuitry only during a defined ownership interval. The non-inverting buffers retain the original logic state, while the two output-enable inputs provide a common way to release all six outputs. This arrangement helps prevent bus contention in systems that combine a processor, memory, and peripheral devices. Texas Instruments specifically describes the family for bus-oriented receivers and transmitters. The design should define enable timing with the bus controller and confirm that downstream receivers maintain valid levels during high-impedance intervals. Supply decoupling and short ground returns are essential for clean switching behavior.
推薦
Test and Measurement Interface Isolation
The SN74HC365D can buffer six instrumentation signals between a test fixture and a shared measurement or switching network. Buffering reduces loading on the originating circuit, and the 3-state outputs allow the fixture to release the lines when another instrument or termination must take control. The six non-inverting channels make it suitable for parallel status, control, or address lines rather than differential high-speed signals. Because the device operates from 2 V to 6 V, select interface levels that remain within the family limits and validate propagation delay for the measurement timing budget. High-impedance behavior must be considered by the receiving circuitry, which should not depend on the disabled driver maintaining a defined voltage.
推薦
Embedded Control Data Fan-Out
The SN74HC365D can distribute six control or status lines from an embedded controller to distant modules while preserving logic polarity and strengthening the source outputs. The 16-SOIC package is convenient for routing across a compact control board, and the 2 V to 6 V operating range supports compatible embedded logic rails. When several modules share a communication line, the common output-enable function can disconnect the SN74HC365D group while another buffer owns the bus. Design the firmware or hardware arbiter to avoid overlapping enable windows, and check timing at the slowest specified supply voltage if the controller relies on a fixed setup or hold margin.
推薦
Shared Peripheral Bus Isolation
The SN74HC365D is appropriate for placing a six-line peripheral group behind a tri-state interface on a shared bus. High impedance releases the peripheral segment when it is not selected, while the non-inverting channels preserve the command and status logic presented to the active controller. The dual output-enable arrangement provides a common disable mechanism for all six lines, reducing the number of control signals required on a crowded board. Texas Instruments identifies bus-oriented receivers and transmitters as intended uses. The implementation must ensure only one driver enables at a time, provide a defined state for the shared bus when every driver is disabled, and validate propagation delay against the peripheral interface timing.
推薦
推薦產品摘要
工程參考資料,適用於 SN74HC365D — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | CD74HC365M | 74HC365D,653 | MC74HC365ADG | 74HCT365D | 74LVC365AD |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SO | 16-SO | 16-SO | 16-SO |
| Brand | Texas Instruments | Texas Instruments | Nexperia | onsemi | Nexperia | Nexperia |
| Function | Hex non-inverting 3-state buffer/line driver | Hex 3-state buffer/line driver | Hex non-inverting 3-state buffer/line driver | Hex 3-state buffer/line driver | Hex 3-state buffer/line driver with TTL-compatible inputs | Hex 3-state buffer/line driver |
| Number of Channels | 6 | 6 | 6 | 6 | 6 | 6 |
| Output Enable Control | 2 shared output-enable inputs | 2 shared output-enable inputs | 2 shared output-enable inputs | 2 shared output-enable inputs | 2 shared output-enable inputs | 2 shared output-enable inputs |
| Input Threshold Type | CMOS-compatible HC input | CMOS-compatible HC input | CMOS-compatible HC input | CMOS-compatible HC input | TTL-compatible HCT input | CMOS-compatible LVC input |
| Disabled Output State | High impedance | High impedance | High impedance | High impedance | High impedance | High impedance |
| Polarity | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting |
主要差異化特點
- Six non-inverting channels can be disabled as one group (對比MC74HC365ADG)
- Direct 74HC365-family interface compatibility (對比74HC365D,653)
- TTL-compatible replacement requires a different input-threshold choice (對比74HCT365D)
設計說明
Use the SN74HC365D as a buffer between a source and a shared bus rather than as an active bus terminator. Keep the device close to the driven receiver when propagation delay or edge-rate control is important. Provide a continuous ground reference and route output-enable traces away from fast clock and data paths. Because all six outputs share the two enable controls, a switching enable can affect every channel simultaneously and should be sequenced to prevent contention.
Place the decoupling capacitor close to the device supply and ground pins, and avoid routing output-enable signals beneath or immediately beside high-speed clock nets. The 16-SOIC footprint requires adequate lead spacing for assembly and inspection. Preserve a direct ground return for every output branch; long or shared return paths can produce unequal edge timing between channels even when the logic function itself is correct.
Do not treat a high-impedance output as a driven logic zero or one. The downstream bus must have an appropriate pull-up, pull-down, or other defined state whenever every driver is disabled. Also verify the active-low enable polarity before layout because driving an enable input to the wrong state can release the outputs unexpectedly. Do not leave unused digital inputs floating, and confirm all timing and current limits from the manufacturer datasheet.
合規資訊
Use the current Texas Instruments product page and material-declaration documentation to confirm environmental, automotive, lead-free, halogen-free, and conflict-minerals status for the exact orderable MPN.