SN74LVC1G125QDBVRQ1 - AEC-Q100 Buffer, 3-State, SOT-23-5 | TI
N.º de pieza: SN74LVC1G125QDBVRQ1 ✓ Activo| Cant. | Precio unitario | Total |
|---|---|---|
| 1 | $0.42 | $0,42 |
| 10 | $0.32 | $3,20 |
| 100 | $0.19 | $19,00 |
| 500 | $0.14 | $70,00 |
| 1.000 | $0.11 | $110,00 |
SN74LVC1G125QDBVRQ1 Descripción general
A single-bus buffer gate is a logic device in the voltage-level and drive-strength hierarchy of digital ICs: buffer gate -> line driver -> bus-interface logic. Its role is to restore signal edges, increase fan-out, and isolate bus segments without inverting logic polarity.
Key features include 5.5V-tolerant inputs for mixed-voltage environments, high output drive from advanced CMOS technology, and robust ESD protection rated at 2000V HBM, 200V MM, and 1000V CDM per the datasheet. The Q1 suffix denotes AEC-Q100 qualification and customer-specific configuration control, making the device suitable for automotive body, cluster, and infotainment modules.
Fabricated on TI's advanced CMOS LVC process, the buffer achieves high speed with low power consumption and balanced drive in both push-pull directions. The NanoStar/NanoFree small-footprint SOT-23-5 package supports dense PCB layouts while maintaining 5V VCC operation capability.
Typical applications include automotive CAN/LIN module I/O buffering, level-compatible bus isolation at 3.3V and 5V, MCU GPIO line driving, and sensor signal gating in 12V automotive electronic control units.
Design tip: tie the OE pin to GND for a permanently enabled buffer; never leave OE floating, as the active-low enable polarity differs from the SN74LVC1G126 variant.
Alternativas directas para SN74LVC1G125QDBVRQ1 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con SN74LVC1G125QDBVRQ1 (mismo factor de forma y huella) — difiere en Output Enable, Output Type, RoHS Status.
Herramienta de comparación rápida — seleccione piezas alternativas para compararlas lado a lado:
SN74LVC1G125DBVR
✅ Sustitución directa✓ En stock
$0.13 / unidad
Ver hoja de datos →SN74LVC1G126QDBVRQ1
⚡ Mismo encapsulado ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
SN74AUP1T34-Q1
⚡ Mismo encapsulado ⚠️ Especificaciones sin verificar✓ En stock
$0.18 / unidad
Ver hoja de datos →74LVC1G125Q-7
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
74LVC1G125GV,125
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
SN74LVC1G125QDBVRQ1 Valores máximos y características eléctricas
| Logic Function | Single non-inverting buffer with 3-state output |
| Supply Voltage Range | 1.65 V to 5.5 V |
| Input Tolerance | 5.5 V tolerant inputs |
| Output Enable | OE active-low (output Hi-Z when OE HIGH) |
| Tipo de salida | 3-state push-pull |
| Automotive Qualification | AEC-Q100 qualified (Q1) |
| ESD HBM | 2000 V |
| ESD MM | 200 V |
| ESD CDM | 1000 V |
| Technology | Advanced CMOS (LVC) |
| Encapsulado | SOT-23-5 (DBV) |
| Tipo de montaje | Surface Mount |
| Estado RoHS | Compliant |
Configuración de pines de SN74LVC1G125QDBVRQ1
| Pin 1 | OE — Output enable, active low (output Hi-Z when HIGH) |
| Pin 2 | GND — Ground |
| Pin 3 | A — Data input (5.5V tolerant) |
| Pin 4 | Y — 3-state non-inverting output |
| Pin 5 | VCC — Power supply, 1.65V to 5.5V |
Aplicaciones típicas
SN74LVC1G125QDBVRQ1 es adecuado para 6 aplicacións: Automotive Body Electronics ECU, Mixed-Voltage Level Compatible Buffering, Instrument Cluster Display Logic, Battery Management System I/O Gating, Industrial Automation Control Logic, Telematics and Gateway Modules.
Automotive Body Electronics ECU
In body control modules and automotive ECUs, the SN74LVC1G125QDBVRQ1 buffers MCU GPIO signals driving switch inputs, relay logic, and lamp-check lines. Its AEC-Q100 qualification makes it suitable for harsh cabin and under-hood electronics where commercial logic is not permitted. The 1.65V-5.5V VCC range lets the same design re-use the part across 3.3V and 5V subsystems, and 2000V HBM ESD tolerance withstands automotive assembly handling. Placed as a 3-state line driver, the OE pin lets the MCU tri-state sensor buses during diagnostics, isolating faulty nodes without relays.
Recomendado
Mixed-Voltage Level Compatible Buffering
The 5.5V-tolerant inputs of the SN74LVC1G125QDBVRQ1 make it a simple one-gate solution in mixed-voltage systems where a 5V legacy signal must gate a 3.3V rail, or vice versa. Powered at 1.65V-5.5V, the input never sees overstress even at 5V signals with VCC lowered, unlike non-tolerant LVC inputs. The 3-state output provides bus isolation during power-up sequencing - asserting OE HIGH tri-states the driver while downstream rails settle. This is frequently used to gate SPI chip-select or enable lines crossing voltage domains in automotive and industrial controllers.
Recomendado
Instrument Cluster Display Logic
Cluster and dashboard modules use the SN74LVC1G125QDBVRQ1 to buffer display-backlight enables, stepper-motor pointer control signals, and indicator LED drive gating. The high output drive from TI's advanced CMOS LVC process restores slow, attenuated edges across long harness-driven PCB traces, and the push-pull 3-state output can be parked in Hi-Z when the display subsystem is powered down. AEC-Q100 qualification and customer-specific configuration control satisfy OEM change-management requirements for tier-1 cluster suppliers, while SOT-23-5 fits dense cluster PCBs.
Recomendado
Battery Management System I/O Gating
In BMS slave boards, the SN74LVC1G125QDBVRQ1 gates cell-monitor daisy-chain control and diagnostic select lines. The 3-state output enables shared single-wire diagnostic buses: multiple buffers connect to one line with only one OE asserted LOW at a time, preventing contention. The 1.65V-5.5V supply matches both 3.3V monitoring ICs and 5V communication ports, and the Q1 automotive grade is required in EV traction-battery environments. The active-low OE also naturally fits watchdog-driven enable logic where a HIGH (fault) state must force Hi-Z.
Recomendado
Industrial Automation Control Logic
In PLC I/O cards and factory automation boards, the buffer restores fan-out-degraded signals from counters, encoder comparators, and optocoupler outputs. Where an industrial variant is acceptable, the same-die SN74LVC1G125DBVR offers a lower-cost path; the Q1 version suits industrial equipment sharing a qualified BOM with automotive lines. The 3-state output supports bus-organized I/O backplanes where multiple cards drive a shared status line. 2000V HBM ESD robustness is valuable near connector edges where field wiring induced transients are handled upstream by TVS diodes.
Recomendado
Telematics and Gateway Modules
Automotive telematics gateways use the SN74LVC1G125QDBVRQ1 to gate cellular-module PWRKEY and reset-control lines and to buffer GPIO between the main SoC and CAN/LIN transceivers. The OE pin allows the MCU to release control lines during module firmware updates, matching the 3-state bus discipline required by shared boot-strap pins. With 5.5V-tolerant inputs, the buffer safely interfaces 5V-tolerant transceiver I/O even while its own rail is 3.3V, eliminating a level-shifting stage and saving board area in space-constrained gateway designs.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para SN74LVC1G125QDBVRQ1 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | SN74LVC1G125DBVR | 74LVC1G125Q-7 | 74LVC1G125GV,125 |
|---|---|---|---|---|
| Package | SOT-23-5 (DBV) | SOT-23-5 (DBV) - same | SOT-23-5 - same | SOT-23-5 - same |
| Brand | Texas Instruments | Texas Instruments | Diodes Incorporated | Nexperia |
| Supply Voltage Range | 1.65 V to 5.5 V | 1.65 V to 5.5 V | 1.65 V to 5.5 V | 1.65 V to 5.5 V |
| Output Enable Polarity | Active-low (Hi-Z when OE HIGH) | Active-low | Active-low | Active-low |
| Input Tolerance | 5.5 V tolerant | 5.5 V tolerant | 5.5 V tolerant | 5.5 V tolerant |
Diferenciadores clave
- AEC-Q100 automotive qualification (frente a SN74LVC1G125DBVR)
- Automotive-compliant cross-brand second source (frente a 74LVC1G125Q-7)
- Active-low OE bus discipline (frente a SN74LVC1G126QDBVRQ1)
Notas de diseño
Do not confuse OE polarity with the SN74LVC1G126: on the G125, output is enabled when OE is LOW and Hi-Z when OE is HIGH. Substituting a G126 without checking OE logic causes permanent bus contention or tri-state. Also never leave OE floating - tie to GND via 0-ohm/10k pull-down for a permanently enabled buffer.
Place a 0.1uF ceramic decoupling capacitor within 2-3 mm of VCC (pin 5) to GND. Keep the A-to-Y trace short for clean edge propagation, and route OE away from switching nodes to avoid glitch-induced tri-stating. The SOT-23-5 footprint (DBV) is standard and allows direct placement of pin-compatible alternatives.
Use the 5.5V input tolerance deliberately: the input may be driven to 5.5V regardless of VCC, but keep VCC within 1.65V-5.5V. In mixed-voltage boards, ensure OE is not asserted from an unpowered voltage domain to avoid back-powering through input protection structures during power sequencing.
Información de cumplimiento
Q1 suffix denotes AEC-Q100 automotive qualification per TI product page. RoHS/lead-free per standard TI SMD packaging for active catalog parts.
