Texas Instruments

TAS5615DKD - 160W Stereo Class-D Amplifier | TI

N.º de pieza: TAS5615DKD ✓ Activo
25 V to 52.5 V Vdss 44-pin HSSOP Package
MOQ: 1 |

TAS5615DKD Descripción general

Texas Instruments TAS5615DKD is an analog-input Class-D audio power amplifier with integrated closed-loop feedback using PurePath HD technology. It supports up to 160 W stereo output into 8-ohm speakers from a single 50 V supply, or up to 300 W mono operation, and is packaged in a 44-pin HSSOP package. According to the manufacturer product page, distortion is below 0.03% THD while retaining the efficiency associated with Class-D operation.

A Class-D audio power amplifier is a switching power stage that converts an analog input waveform into a high-frequency PWM representation and reconstructs the audio signal at the speaker output. The TAS5615 family belongs to the broader class of integrated audio amplifiers, combining a power-conversion stage with feedback control in one device. Its integrated PurePath HD closed-loop feedback system is intended to improve linearity and reduce distortion compared with relying only on an external speaker feedback network.

The TAS5615DKD accepts analog audio inputs and is designed for high-power stereo and mono speaker drive. Its stated 160 W stereo capability is based on operation from a 50 V supply, while the 300 W mono figure supports dedicated single-channel or bridged configurations. The supported power-supply range shown in the component listing is 25 V to 52.5 V, and a separate 10.8 V to 13.2 V range is associated with its internal auxiliary supply domain.

PurePath HD technology is the principal technical differentiator of this power stage. Closed-loop feedback samples the output and corrects the switching waveform, supporting the manufacturer’s specified total harmonic distortion below 0.03%. This combination of analog input, Class-D efficiency, and feedback-based distortion control makes the device suitable for professional audio amplification, home-theater receivers, powered speakers, subwoofers, and other systems using low-impedance loudspeakers.

For stereo installations, the amplifier drives left and right channels from analog inputs while operating from a high-voltage supply. A bridged mono arrangement can increase the available output into one speaker or a matched pair of speakers. The exact output power depends on supply voltage, speaker impedance, channel configuration, thermal conditions, and the load presented by the speaker network, so these conditions must be confirmed during amplifier and thermal design.

The 44-pin HSSOP package requires careful PCB layout and adequate copper for heat removal. Power and ground connections should use short, wide traces with low loop area, while the manufacturer’s layout guidance should govern input routing, feedback connections, decoupling, and thermal via placement. The device is a power IC, but thermal design must use the maximum expected dissipation at the selected supply voltage and load rather than relying only on nominal output power.

This product page combines the manufacturer’s core performance claims with package, interface, supply, and sourcing details, while adding application guidance and verified drop-in replacement status for engineering evaluation. Use the Request a Quote form for current commercial availability, and consult the manufacturer datasheet before finalizing the PCB, heat sink, output network, and protection scheme.

Alternativas directas para TAS5615DKD — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

TAS5615DKDR

✅ Sustitución directa
📦 44-pin HSSOP (DKD)
Same TAS5615 electrical configuration and 44-pin HSSOP footprint; only the manufacturer packaging code differs, with no identified change to output power, supply voltage, or input architecture

📋 Alternativa de referencia (no en el catálogo)

TAS5615DKD Valores máximos y características eléctricas

Product Type Analog-input Class-D audio power amplifier
Maximum Stereo Output Power 160 W into 8 ohms at 50 V supply
Maximum Mono Output Power 300 W
Total Harmonic Distortion <0.03% THD
Power Supply Voltage 25 V to 52.5 V
Auxiliary Supply Voltage 10.8 V to 13.2 V
Nominal High-Voltage Supply 50 V
Channel Configuration 1-channel mono or 2-channel stereo
Feedback Architecture Integrated closed-loop PurePath HD feedback
Input Type Analog input
Supported Speaker Load 8 ohms
Encapsulado 44-pin HSSOP
Recuento de pines 44 pins
Tipo de montaje Surface mount

Guía de configuración de pines de TAS5615DKD 44-pin hssop

Configuración de pines para TAS5615DKD (encapsulado 44-pin hssop). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.

Diagrama de patillaje del encapsulado 44-pin hssop para TAS5615DKD

No hay datos detallados de patillaje disponibles para TAS5615DKD.

Consulte la hoja de datos para ver la configuración completa de patillas.

TAS5615DKD Área de funcionamiento seguro

Operación continua de CC

Aplicaciones típicas

TAS5615DKD es adecuado para 6 aplicacións: Professional Stereo Power Amplifier, Bridged Mono Subwoofer Amplifier, Home Theater Amplifier, Powered Speaker and Monitor, High-Power Audio Distribution Amplifier, Venue Loudspeaker Power Stage.

🎧

Professional Stereo Power Amplifier

TAS5615DKD fits a professional stereo output stage requiring analog input and substantial continuous power into 8-ohm loudspeakers. Its manufacturer-rated capability reaches 160 W per stereo channel from a 50 V supply, while the PurePath HD closed-loop architecture supports less than 0.03% THD. The amplifier can sit downstream of a preamp or mixing console in installed-audio racks, active monitors, or venue reinforcement systems. Designers should budget the 25 V to 52.5 V power rail, use the specified output network, and provide copper area and thermal vias beneath the HSSOP. Because output power depends on impedance and thermal conditions, verify the selected speaker network and continuous operating profile against the datasheet test conditions before production.

🔊

Bridged Mono Subwoofer Amplifier

The TAS5615DKD can serve as the power stage in a bridged mono subwoofer amplifier, using its listed capability of up to 300 W for a dedicated low-impedance channel. The high-voltage operating range of 25 V to 52.5 V supports conventional high-power audio rails, while analog input allows the signal to come from a crossover, preamp, or line-level mixer. Bridged operation requires the exact output-network and speaker connection shown by Texas Instruments; neither speaker terminal should be treated as an arbitrary system ground. Heat management is especially important because low-impedance loads can produce high continuous dissipation. Validate voice-coil loading, DC offset, protection behavior, and thermal margins in the final enclosure.

📺

Home Theater Amplifier

TAS5615DKD is appropriate for the main power-amplifier section of a home-theater receiver or multichannel amplifier driving 8-ohm speaker channels. Its analog input accepts a line-level signal from preamplification and volume-control circuitry, while the Class-D output stage provides high conversion efficiency and up to 160 W per channel at the manufacturer’s 50 V condition. The less-than-0.03% THD specification supports low-distortion playback. A practical design must include channel-specific gain staging, speaker filtering where the architecture requires it, overcurrent protection, a stable high-voltage supply, and forced-air or heatsinking appropriate to the enclosure. Use the manufacturer layout and test circuits to preserve performance.

🎚️

Powered Speaker and Monitor

TAS5615DKD can serve as the internal power amplifier of an active bookshelf speaker, studio monitor, or multimedia speaker enclosure. An analog input from a preamp or active crossover keeps the signal path compatible with conventional analog audio equipment, while the integrated power stage supports up to 160 W stereo into 8-ohm drivers from a 50 V supply. PurePath HD feedback is valuable in a compact enclosure where acoustic output quality and amplifier efficiency both matter. Place the device according to the manufacturer’s thermal and layout guidance, keep switching-current paths confined to the power section, and test the chosen crossover and enclosure for resonances. Continuous output must be derated appropriately when ambient temperature or airflow is constrained.

🌐

High-Power Audio Distribution Amplifier

TAS5615DKD is suited to a line-level-to-speaker distribution amplifier when multiple zones or speaker taps require Class-D efficiency and analog compatibility. Each amplifier channel can use the same integrated feedback technology and the manufacturer’s high-power 8-ohm drive capability. The 25 V to 52.5 V rail range permits integration into professional installed-sound power systems, but each tap must be engineered for continuous dissipation, amplifier stability, and safe speaker connection. Feedback-network components and output filters should follow the manufacturer reference design rather than being copied from an unrelated Class-D device. Validate channel-to-channel gain matching and test the system with the intended cable and speaker loads before deployment.

🏭

Venue Loudspeaker Power Stage

TAS5615DKD can be used as the output stage in a compact venue loudspeaker amplifier or line-array feed enclosure requiring analog drive and high power from a 50 V rail. The manufacturer-rated 160 W stereo capability into 8-ohm speakers provides a useful design target, while the integrated PurePath HD feedback helps control distortion in a high-power switching amplifier. Deployment requires careful attention to the recommended output filter, speaker protection, fault handling, and thermal design. Low-impedance loads and long cable runs can influence amplifier behavior, so evaluate the intended network rather than assuming nominal 8-ohm behavior. Confirm the enclosure’s heat-transfer path and verify the complete configuration with representative program material before installation.

What is the TAS5615DKD?
The TAS5615DKD is a Texas Instruments analog-input Class-D audio power amplifier in a 44-pin HSSOP package. According to the manufacturer product page, it uses integrated closed-loop PurePath HD feedback, supports up to 160 W stereo into 8-ohm speakers from a 50 V supply, and can deliver up to 300 W in mono operation. It is intended for high-power professional audio, home theater, powered-speaker, and subwoofer amplifier systems.
How much power can the TAS5615DKD output?
The TAS5615DKD can deliver up to 160 W per channel in stereo operation into 8-ohm speakers from a single 50 V supply. Its listed maximum mono capability is 300 W. These ratings represent the manufacturer’s headline configurations; actual continuous output depends on the selected supply, amplifier-channel mode, speaker impedance, signal level, thermal design, and output filtering. The datasheet should be used for the corresponding test conditions.
What is the operating voltage of TAS5615DKD?
The principal TAS5615DKD power-supply operating range is 25 V to 52.5 V, as shown in the manufacturer component data. The manufacturer also identifies 50 V as the supply used for the 160 W stereo rating. A separate 10.8 V to 13.2 V range applies to the auxiliary supply domain. Both domains must be designed for the regulator, sequencing, and protection requirements in the application circuit.
What are the key specifications of TAS5615DKD that engineers should know?
The principal TAS5615DKD specifications are 160 W stereo output into 8 ohms, up to 300 W mono output, less than 0.03% THD, a 25 V to 52.5 V power-supply range, and a 44-pin HSSOP package. The device accepts analog input and uses integrated closed-loop PurePath HD feedback. These values define its primary role as a high-power, high-efficiency Class-D audio output stage.
What is the difference between stereo and mono operation on TAS5615DKD?
Stereo operation uses the TAS5615DKD to drive two independent channels, while bridged mono operation combines the amplifier outputs to drive one higher-power channel or speaker network. The manufacturer states up to 160 W stereo from 50 V and up to 300 W mono. Bridging changes the channel arrangement and load connection, so the output-network and speaker-grounding design must follow the manufacturer’s recommended configuration.
What is TAS5615DKD vs TAS5615 and are they the same device?
TAS5615 identifies the Texas Instruments power-amplifier family, while TAS5615DKD is the orderable device designation that identifies its package and ordering configuration. The manufacturer product page is published under TAS5615, and the component listing identifies TAS5615DKD as a 44-pin HSSOP Class-D amplifier. Treat TAS5615 as the family identifier and TAS5615DKD as the specific orderable MPN rather than assuming the two strings represent different amplifier designs.
When should I choose TAS5615DKD for an amplifier design?
Choose the TAS5615DKD when the design needs analog audio input, high-power low-impedance speaker drive, and Class-D efficiency. It is particularly suitable where a 160 W stereo or 300 W mono capability and less than 0.03% THD are important. Do not select it when the available supply is outside 25 V to 52.5 V or when a different package, lower-voltage architecture, or integrated codec and volume-control function is required.
Is TAS5615DKD suitable for home theater and powered speakers?
Yes, TAS5615DKD is suitable for home-theater and powered-speaker power stages using low-impedance loudspeakers. Its analog input can receive a preamplified line-level signal, while the high-voltage Class-D output stage supplies up to 160 W stereo from 50 V. The system still needs a preamplifier, speaker filters if required, enclosure ventilation, heat sinking, and protection appropriate to the selected load and wiring.
Where can I download the TAS5615DKD datasheet PDF?
The official TAS5615 product page provides the manufacturer’s data-sheet and support information for the family containing TAS5615DKD. Direct third-party document mirrors are also listed for this part, but the Texas Instruments page is the preferred source for revisions and support material. When designing the board, use the pin-description table and layout examples in the manufacturer document to assign every one of the 44 HSSOP connections.
Where can I find the TAS5615DKD pinout?
The TAS5615DKD pinout is found in the pin-description table of the manufacturer datasheet for the TAS5615 family. The device has 44 HSSOP pins, including its analog audio inputs, power connections, feedback and output-network connections, ground references, and auxiliary-domain connections. Use the manufacturer’s pin table and package drawing when assigning PCB nets, because the exposed thermal and electrical requirements must be implemented as a complete layout.
Where can I buy TAS5615DKD online?
Use the Request a Quote form on this page to request TAS5615DKD availability, current pricing, and lead time from XAIPART. The part is a 44-pin HSSOP Texas Instruments Class-D audio amplifier rated for up to 160 W stereo into 8 ohms from a 50 V supply. Include the required quantity, reel or tray preference, destination, and target date so the commercial response can reflect the complete procurement request.
What is the price of TAS5615DKD?
The current TAS5615DKD price is obtained through the Request a Quote form on this page because commercial pricing can change with quantity, availability, and packaging requirements. Submit the desired order quantity and package-delivery preference for a current quotation. The device is specified as a 44-pin HSSOP Texas Instruments analog-input Class-D amplifier with up to 160 W stereo output from a 50 V supply.
What is the lead time and stock status for TAS5615DKD?
Use the Request a Quote form on this page to confirm the current stock position, lead time, and minimum order quantity for TAS5615DKD. The request should state the required quantity and whether tape-and-reel, tray, or another permitted delivery format is needed. The product is a high-power 44-pin HSSOP Class-D amplifier, so packaging and schedule should be confirmed together rather than assuming generic semiconductor availability.
What can replace TAS5615DKD?
No drop-in replacement can be confirmed from the available cross-reference records for TAS5615DKD. A valid replacement must use the same 44-pin HSSOP footprint, preserve pin-to-pin connections, support the 25 V to 52.5 V supply range, and reproduce the required stereo or mono output capability. Until those electrical and thermal details are confirmed, treat any candidate as a redesign candidate rather than a drop-in substitution and use the Request a Quote form for factory support.
Is there a verified cross-brand equivalent for TAS5615DKD?
No verified cross-brand drop-in equivalent is established for TAS5615DKD. The available cross-reference results contain search tools and the original Texas Instruments listing rather than a qualified competitor with a confirmed 44-pin HSSOP pinout, supply range, output power, and thermal performance. A candidate should not be considered interchangeable solely because its headline wattage is similar; verify the complete pin, electrical, acoustic, and layout requirements first.
How should TAS5615DKD be handled for thermal reliability?
TAS5615DKD should be designed for the worst-case dissipation created by its selected supply voltage, stereo or bridged mode, and speaker load. The 44-pin HSSOP package must use the PCB copper and thermal-via arrangement shown in the manufacturer layout guidance. Do not interpret the 160 W stereo or 300 W mono headline ratings as requiring no heat sinking; continuous output capability depends on ambient temperature, load impedance, and the implemented thermal path.

Datos de referencia de ingeniería para TAS5615DKD — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose TAS5615DKD for a high-power analog-input Class-D output stage that must drive 8-ohm speakers from a 25 V to 52.5 V supply. Its 160 W stereo rating is appropriate for professional power amplifiers, home-theater output stages, active monitors, and powered speakers, while the 300 W mono capability makes it useful for bridged subwoofer designs. Prefer it when analog compatibility and PurePath HD feedback are priorities and the PCB can accommodate a 44-pin HSSOP with substantial thermal copper. No qualified drop-in replacement is established in the available records, so a competing amplifier should be treated as a redesign candidate unless its exact package, pinout, supply behavior, output network, and thermal limits are independently confirmed. Avoid this device when the rail is below 25 V, when a compact low-voltage package is required, or when the design depends on features not provided by this analog power stage.

Comparación con alternativas

Parámetro Este producto
Brand Texas Instruments
Package 44-pin HSSOP
Amplifier Type Analog-input Class-D
Stereo Output Power Up to 160 W into 8 ohms at 50 V
Mono Output Power Up to 300 W
Total Harmonic Distortion <0.03% THD
Power Supply Range 25 V to 52.5 V
Auxiliary Supply Range 10.8 V to 13.2 V
Feedback Architecture Integrated closed-loop PurePath HD
Channel Configuration Mono or stereo

Diferenciadores clave

  • High integrated stereo output capability (frente a Lower-power Class-D amplifier options)
  • Dedicated high-power mono operation (frente a Stereo-only amplifier configurations)
  • Integrated closed-loop feedback (frente a Class-D stages without integrated output feedback)

Notas de diseño

Thermal design must be based on estimated worst-case dissipation at the maximum continuous load, not on the nominal audio rating alone. Estimated: with a 50 V rail, a 4 V average output voltage, and 1 A of average output current, the approximate amplifier dissipation is 46 W before accounting for additional circuit losses. Use this estimate only as a design starting point, then apply the manufacturer’s thermal model and the actual stereo or bridged-mode operating condition. Provide the HSSOP with the specified PCB copper area and thermal vias, and verify junction and enclosure temperatures during sustained high-level playback.

Implement the power stage with short, wide high-current traces and a low-inductance supply-return path. Place input, feedback, and output-network connections away from switching-node copper, and route them on the quiet side of the board where practical. Follow the manufacturer’s reference layout for the 44-pin HSSOP, including exposed-pad connection and via arrangement. Incorrect feedback routing or a long ground return can increase distortion and destabilize the amplifier even when the external component values are correct.

Do not connect the loudspeaker in a bridged arrangement unless the complete output network and terminal polarity follow the manufacturer circuit. A bridged output can place both speaker terminals at an elevated voltage relative to system ground, creating shock and grounding hazards. Also verify the output filter, feedback components, supply sequencing, and protection scheme before energizing the amplifier. Common ground between the bridged speaker and external audio equipment must be assessed carefully to prevent unintended current paths.

Design the 25 V to 52.5 V supply for startup current, output-current transients, local decoupling, and fault conditions. Place bulk and high-frequency decoupling capacitors at the device power pins with very short connections, following the component values and layout in the manufacturer datasheet. Estimated: at 50 V input and 8 ohms, the peak current corresponding to 160 W is 20 A, so the supply and copper path must tolerate substantial transient current without causing voltage droop or unstable operation.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The manufacturer product page should be used to confirm current environmental, material, and qualification declarations for the exact orderable MPN.

Datos verificados el: 2026-11-10 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

TAS5615DKD datasheet TAS5615DKD specifications TAS5615DKD pinout TAS5615DKD 44 HSSOP pinout TAS5615DKD power supply TAS5615DKD 160W stereo TAS5615DKD 300W mono Texas Instruments TAS5615DKD TAS5615DKD class D amplifier TAS5615DKD home theater amplifier TAS5615DKD subwoofer amplifier TAS5615DKD equivalent TAS5615DKD replacement TAS5615DKD price TAS5615DKD stock

Componentes & términos relacionados

Texas Instruments TAS5615DKD TAS5615 PurePath HD Class-D amplifier analog-input power amplifier audio power amplifier integrated amplifier closed-loop feedback total harmonic distortion THD 160 W stereo output 300 W mono output 8-ohm speaker 50 V power supply 25 V to 52.5 V power range 44-pin HSSOP HSSOP package family surface-mount package home theater amplification professional audio powered speakers subwoofer amplification Class-D switching amplifier
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ