TAS5615DKD - 160W Stereo Class-D Amplifier | TI
MPN: TAS5615DKD ✓ ActiveTAS5615DKD Overview
A Class-D audio power amplifier is a switching power stage that converts an analog input waveform into a high-frequency PWM representation and reconstructs the audio signal at the speaker output. The TAS5615 family belongs to the broader class of integrated audio amplifiers, combining a power-conversion stage with feedback control in one device. Its integrated PurePath HD closed-loop feedback system is intended to improve linearity and reduce distortion compared with relying only on an external speaker feedback network.
The TAS5615DKD accepts analog audio inputs and is designed for high-power stereo and mono speaker drive. Its stated 160 W stereo capability is based on operation from a 50 V supply, while the 300 W mono figure supports dedicated single-channel or bridged configurations. The supported power-supply range shown in the component listing is 25 V to 52.5 V, and a separate 10.8 V to 13.2 V range is associated with its internal auxiliary supply domain.
PurePath HD technology is the principal technical differentiator of this power stage. Closed-loop feedback samples the output and corrects the switching waveform, supporting the manufacturer’s specified total harmonic distortion below 0.03%. This combination of analog input, Class-D efficiency, and feedback-based distortion control makes the device suitable for professional audio amplification, home-theater receivers, powered speakers, subwoofers, and other systems using low-impedance loudspeakers.
For stereo installations, the amplifier drives left and right channels from analog inputs while operating from a high-voltage supply. A bridged mono arrangement can increase the available output into one speaker or a matched pair of speakers. The exact output power depends on supply voltage, speaker impedance, channel configuration, thermal conditions, and the load presented by the speaker network, so these conditions must be confirmed during amplifier and thermal design.
The 44-pin HSSOP package requires careful PCB layout and adequate copper for heat removal. Power and ground connections should use short, wide traces with low loop area, while the manufacturer’s layout guidance should govern input routing, feedback connections, decoupling, and thermal via placement. The device is a power IC, but thermal design must use the maximum expected dissipation at the selected supply voltage and load rather than relying only on nominal output power.
This product page combines the manufacturer’s core performance claims with package, interface, supply, and sourcing details, while adding application guidance and verified drop-in replacement status for engineering evaluation. Use the Request a Quote form for current commercial availability, and consult the manufacturer datasheet before finalizing the PCB, heat sink, output network, and protection scheme.
Drop-in alternatives for TAS5615DKD — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
TAS5615DKDR
✅ Drop-In📋 Reference alternative (not in catalog)
TAS5615DKD Maximum Ratings & Electrical Characteristics
| Product Type | Analog-input Class-D audio power amplifier |
| Maximum Stereo Output Power | 160 W into 8 ohms at 50 V supply |
| Maximum Mono Output Power | 300 W |
| Total Harmonic Distortion | <0.03% THD |
| Power Supply Voltage | 25 V to 52.5 V |
| Auxiliary Supply Voltage | 10.8 V to 13.2 V |
| Nominal High-Voltage Supply | 50 V |
| Channel Configuration | 1-channel mono or 2-channel stereo |
| Feedback Architecture | Integrated closed-loop PurePath HD feedback |
| Input Type | Analog input |
| Supported Speaker Load | 8 ohms |
| Package | 44-pin HSSOP |
| Pin Count | 44 pins |
| Mounting Type | Surface mount |
TAS5615DKD 44-pin hssop Pin Configuration Guide
Pin configuration for TAS5615DKD (44-pin hssop package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for TAS5615DKD.
Refer to the datasheet for full pin configuration.
TAS5615DKD Safe Operating Area
Typical Applications
TAS5615DKD is suitable for 6 applications: Professional Stereo Power Amplifier, Bridged Mono Subwoofer Amplifier, Home Theater Amplifier, Powered Speaker and Monitor, High-Power Audio Distribution Amplifier, Venue Loudspeaker Power Stage.
Professional Stereo Power Amplifier
TAS5615DKD fits a professional stereo output stage requiring analog input and substantial continuous power into 8-ohm loudspeakers. Its manufacturer-rated capability reaches 160 W per stereo channel from a 50 V supply, while the PurePath HD closed-loop architecture supports less than 0.03% THD. The amplifier can sit downstream of a preamp or mixing console in installed-audio racks, active monitors, or venue reinforcement systems. Designers should budget the 25 V to 52.5 V power rail, use the specified output network, and provide copper area and thermal vias beneath the HSSOP. Because output power depends on impedance and thermal conditions, verify the selected speaker network and continuous operating profile against the datasheet test conditions before production.
Recommended
Bridged Mono Subwoofer Amplifier
The TAS5615DKD can serve as the power stage in a bridged mono subwoofer amplifier, using its listed capability of up to 300 W for a dedicated low-impedance channel. The high-voltage operating range of 25 V to 52.5 V supports conventional high-power audio rails, while analog input allows the signal to come from a crossover, preamp, or line-level mixer. Bridged operation requires the exact output-network and speaker connection shown by Texas Instruments; neither speaker terminal should be treated as an arbitrary system ground. Heat management is especially important because low-impedance loads can produce high continuous dissipation. Validate voice-coil loading, DC offset, protection behavior, and thermal margins in the final enclosure.
Recommended
Home Theater Amplifier
TAS5615DKD is appropriate for the main power-amplifier section of a home-theater receiver or multichannel amplifier driving 8-ohm speaker channels. Its analog input accepts a line-level signal from preamplification and volume-control circuitry, while the Class-D output stage provides high conversion efficiency and up to 160 W per channel at the manufacturer’s 50 V condition. The less-than-0.03% THD specification supports low-distortion playback. A practical design must include channel-specific gain staging, speaker filtering where the architecture requires it, overcurrent protection, a stable high-voltage supply, and forced-air or heatsinking appropriate to the enclosure. Use the manufacturer layout and test circuits to preserve performance.
Recommended
Powered Speaker and Monitor
TAS5615DKD can serve as the internal power amplifier of an active bookshelf speaker, studio monitor, or multimedia speaker enclosure. An analog input from a preamp or active crossover keeps the signal path compatible with conventional analog audio equipment, while the integrated power stage supports up to 160 W stereo into 8-ohm drivers from a 50 V supply. PurePath HD feedback is valuable in a compact enclosure where acoustic output quality and amplifier efficiency both matter. Place the device according to the manufacturer’s thermal and layout guidance, keep switching-current paths confined to the power section, and test the chosen crossover and enclosure for resonances. Continuous output must be derated appropriately when ambient temperature or airflow is constrained.
Recommended
High-Power Audio Distribution Amplifier
TAS5615DKD is suited to a line-level-to-speaker distribution amplifier when multiple zones or speaker taps require Class-D efficiency and analog compatibility. Each amplifier channel can use the same integrated feedback technology and the manufacturer’s high-power 8-ohm drive capability. The 25 V to 52.5 V rail range permits integration into professional installed-sound power systems, but each tap must be engineered for continuous dissipation, amplifier stability, and safe speaker connection. Feedback-network components and output filters should follow the manufacturer reference design rather than being copied from an unrelated Class-D device. Validate channel-to-channel gain matching and test the system with the intended cable and speaker loads before deployment.
Recommended
Venue Loudspeaker Power Stage
TAS5615DKD can be used as the output stage in a compact venue loudspeaker amplifier or line-array feed enclosure requiring analog drive and high power from a 50 V rail. The manufacturer-rated 160 W stereo capability into 8-ohm speakers provides a useful design target, while the integrated PurePath HD feedback helps control distortion in a high-power switching amplifier. Deployment requires careful attention to the recommended output filter, speaker protection, fault handling, and thermal design. Low-impedance loads and long cable runs can influence amplifier behavior, so evaluate the intended network rather than assuming nominal 8-ohm behavior. Confirm the enclosure’s heat-transfer path and verify the complete configuration with representative program material before installation.
Recommended
Engineering reference data for TAS5615DKD — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product |
|---|---|
| Brand | Texas Instruments |
| Package | 44-pin HSSOP |
| Amplifier Type | Analog-input Class-D |
| Stereo Output Power | Up to 160 W into 8 ohms at 50 V |
| Mono Output Power | Up to 300 W |
| Total Harmonic Distortion | <0.03% THD |
| Power Supply Range | 25 V to 52.5 V |
| Auxiliary Supply Range | 10.8 V to 13.2 V |
| Feedback Architecture | Integrated closed-loop PurePath HD |
| Channel Configuration | Mono or stereo |
Key Differentiators
- High integrated stereo output capability (vs Lower-power Class-D amplifier options)
- Dedicated high-power mono operation (vs Stereo-only amplifier configurations)
- Integrated closed-loop feedback (vs Class-D stages without integrated output feedback)
Design Notes
Thermal design must be based on estimated worst-case dissipation at the maximum continuous load, not on the nominal audio rating alone. Estimated: with a 50 V rail, a 4 V average output voltage, and 1 A of average output current, the approximate amplifier dissipation is 46 W before accounting for additional circuit losses. Use this estimate only as a design starting point, then apply the manufacturer’s thermal model and the actual stereo or bridged-mode operating condition. Provide the HSSOP with the specified PCB copper area and thermal vias, and verify junction and enclosure temperatures during sustained high-level playback.
Implement the power stage with short, wide high-current traces and a low-inductance supply-return path. Place input, feedback, and output-network connections away from switching-node copper, and route them on the quiet side of the board where practical. Follow the manufacturer’s reference layout for the 44-pin HSSOP, including exposed-pad connection and via arrangement. Incorrect feedback routing or a long ground return can increase distortion and destabilize the amplifier even when the external component values are correct.
Do not connect the loudspeaker in a bridged arrangement unless the complete output network and terminal polarity follow the manufacturer circuit. A bridged output can place both speaker terminals at an elevated voltage relative to system ground, creating shock and grounding hazards. Also verify the output filter, feedback components, supply sequencing, and protection scheme before energizing the amplifier. Common ground between the bridged speaker and external audio equipment must be assessed carefully to prevent unintended current paths.
Design the 25 V to 52.5 V supply for startup current, output-current transients, local decoupling, and fault conditions. Place bulk and high-frequency decoupling capacitors at the device power pins with very short connections, following the component values and layout in the manufacturer datasheet. Estimated: at 50 V input and 8 ohms, the peak current corresponding to 160 W is 20 A, so the supply and copper path must tolerate substantial transient current without causing voltage droop or unstable operation.
Compliance Information
The manufacturer product page should be used to confirm current environmental, material, and qualification declarations for the exact orderable MPN.