Texas Instruments

THS4042CD - 165MHz Dual High-Speed Op Amp | Texas Instruments

N.º de pieza: THS4042CD ✓ Activo
8-SOIC (D) Package
MOQ: 1 |

THS4042CD Descripción general

The Texas Instruments THS4042CD is a dual C-stable voltage-feedback operational amplifier with a 165 MHz bandwidth, a 400 V/µs slew rate, and an 8-SOIC package. The device provides two independent high-speed amplifier channels for signal conditioning, video-line driving, and ADC input buffering. Its C-stable architecture supports operation at all closed-loop gains in both inverting and noninverting configurations, while its ability to drive capacitive loads makes it suitable for high-bandwidth analog systems.

A high-speed voltage-feedback operational amplifier is an analog signal-conditioning IC that combines wide closed-loop bandwidth with high slew rate. The THS4042 belongs to the operational-amplifier hierarchy within analog ICs, enabling rapid response to small input-voltage changes while preserving the gain and phase behavior required by feedback control loops. This is useful where conventional general-purpose amplifiers cannot preserve signal amplitude or timing through long PCB traces, cable capacitance, sampling networks, or successive-conversion systems.

The two amplifier channels provide a 165 MHz bandwidth and a 400 V/µs slew rate. These characteristics support demanding video, communications, test-and-measurement, and data-acquisition signal paths. The C-stable design allows closed-loop gains from +1 to +20 without requiring external compensation components. The device also supports driving capacitive loads, including long video lines, while its 80 dB CMRR helps reject common-mode noise coupled into the input stage.

The THS4042 uses a voltage-feedback topology designed for straightforward implementation with conventional external feedback and gain-setting resistors. Its wide bandwidth enables small-signal operation at high frequencies, while the 400 V/µs slew rate determines large-signal settling behavior. The dual-channel configuration can reduce board area when two related high-speed signals must be amplified, conditioned, or buffered.

Typical uses include driving video lines, buffering high-speed ADC inputs, amplifying communications signals, and supporting instrumentation and test-equipment front ends. For ADC buffering, the amplifier can isolate the converter from the source impedance, reducing sampling kickback. For video-line driving, the capacitive-load capability and high slew rate help preserve edge fidelity over terminated or unterminated interconnects.

PCB implementation should minimize trace lengths around the amplifier, preserve the impedance environment of high-frequency feedback loops, and provide a low-inductance ground return. Input and output placement should avoid routing critical signals beside or beneath the device. Decoupling capacitors should connect directly to the relevant supply and ground pins, while resistor networks should remain close to their associated input or feedback nodes.

This product page consolidates the manufacturer-defined bandwidth, slew-rate, channel-count, package, and application characteristics with purchasing guidance and practical implementation notes. It also distinguishes the exact THS4042CD order code from packaging or channel-count variants that are not necessarily direct substitutions.

Alternativas directas para THS4042CD — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con THS4042CD (mismo factor de forma y huella) — difiere en Amplifier Type, Package.

Texas Instruments
Amplifier Type: Dual voltage-feedback operational amplifier
Package: 8-SOIC
Comparar con THS4042CD →

THS4042ID

✅ Sustitución directa
Texas Instruments
📦 8-pin SOIC
Dual voltage-feedback operational amplifier · 2 channels · 165 MHz · 400 V/µs · C-stable · 100 mA typical · -75 dBc at 1 MHz · ±16 V/32 V

Consulte el precio

Ver hoja de datos →

AD826ARZ

✅ Sustitución directa
📦 8-pin SOIC
Same 8-pin SOIC package class; the cross-reference candidate is from Analog Devices, but its channel count, pin assignments, supply range, bandwidth, slew rate, and distortion must be verified against the THS4042CD before substitution.

📋 Alternativa de referencia (no en el catálogo)

THS4042CD Valores máximos y características eléctricas

Amplifier Type Voltage-feedback operational amplifier
Number of Channels 2 channels
Gain-Bandwidth Product 165 MHz
Slew Rate 400 V/µs
Common-Mode Rejection Ratio 80 dB
Compensation C-stable
Capacitive Load Drive Capable of driving capacitive loads
Closed-Loop Gain Support All gains in inverting and noninverting configurations
Rango de temperatura de funcionamiento 0°C to 70°C
Encapsulado 8-SOIC (D)
Número de pines 8 pins
Tipo de montaje Surface mount

Guía de configuración de pines de THS4042CD 8-soic (d)

Configuración de pines para THS4042CD (encapsulado 8-soic (d)). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.

Diagrama de patillaje del encapsulado 8-soic (d) para THS4042CD

No hay datos detallados de patillaje disponibles para THS4042CD.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

THS4042CD es adecuado para 6 aplicacións: High-Speed ADC Input Buffering, Video-Line Signal Driving, Communications Signal Conditioning, Instrumentation Front-End Amplification, Test and Measurement Signal Capture, High-Speed Clock and Data Conditioning.

⚡

High-Speed ADC Input Buffering

The THS4042CD fits between a high-speed signal source and an ADC because its 165 MHz bandwidth and 400 V/µs slew rate preserve fast transitions while the second channel can provide complementary conditioning. Its ability to drive capacitive loads helps isolate the converter input from source impedance and reduces sampling kickback into the driver. Place the device close to the ADC, use short ground returns, and account for the amplifier input capacitance when setting source and feedback impedances.

📺

Video-Line Signal Driving

The THS4042CD is suitable for driving video lines because its 165 MHz bandwidth and 400 V/µs slew rate support rapid edge reproduction over terminated or unterminated interconnects. Its C-stable operation permits use at all closed-loop gains in noninverting and inverting configurations, while capacitive-load drive helps accommodate connector and cable loading. Preserve controlled trace geometry, provide a low-impedance return path, and verify the receiver's termination requirements to minimize reflections.

🌐

Communications Signal Conditioning

The dual THS4042CD can condition two related communications signals with 165 MHz bandwidth and a 400 V/µs slew rate. The wide small-signal bandwidth and high large-signal response support gain stages, impedance-conversion blocks, and clock-like signal paths where distortion or slow edges would impair system timing. Use one channel for the primary signal and the second for monitoring or differential support, while observing high-frequency layout practices around the SOIC-8 footprint.

🔧

Instrumentation Front-End Amplification

The THS4042CD can serve as a high-speed instrumentation front end when sensor or test signals require more bandwidth than a conventional precision amplifier provides. Its 80 dB CMRR helps suppress common-mode disturbance, while the 165 MHz bandwidth and 400 V/µs slew rate preserve rapid signal components. The dual arrangement supports paired measurement channels or an auxiliary buffer, but the application must be checked against the amplifier's complete input, output, and supply operating ranges.

📡

Test and Measurement Signal Capture

The THS4042CD is appropriate for high-bandwidth test points where the instrument must capture or drive signals with fast edges and preserve amplitude relationships. Its 165 MHz bandwidth supports small-signal measurement bandwidth, and the 400 V/µs slew rate improves large-signal response compared with many general-purpose amplifiers. Position the amplifier near the measurement interface, keep probe and fixture capacitance controlled, and verify that the selected closed-loop gain remains stable.

🖥️

High-Speed Clock and Data Conditioning

The THS4042CD can condition low-amplitude, fast-edge clock or data signals when the path requires bandwidth beyond ordinary logic-buffer limits. The 165 MHz gain-bandwidth product and 400 V/µs slew rate help maintain signal amplitude and timing through short PCB routes, while dual channels allow related control or monitoring signals to be processed together. Keep input and feedback traces short, control capacitive loading, and compare the propagated timing with the system budget.

What are the key specifications of THS4042CD that engineers should know?
The THS4042CD is a dual, 165 MHz C-stable voltage-feedback operational amplifier with a 400 V/µs slew rate, 80 dB CMRR, and an 8-SOIC package. According to the Texas Instruments THS4042 datasheet, the device can drive capacitive loads and remains stable at all gains in both inverting and noninverting configurations. Its two independent channels make it suitable for paired high-speed signal paths such as video-line drivers and ADC input buffers.
What is the operating bandwidth of THS4042CD?
The THS4042CD has a 165 MHz gain-bandwidth product. This bandwidth allows the amplifier to provide closed-loop gain at frequencies approaching the device's specified limit, depending on the gain setting and circuit implementation. Texas Instruments identifies the THS4042 as a C-stable, dual voltage-feedback amplifier, and the manufacturer datasheet describes it as suitable for high-speed video, ADC-buffer, and communications applications.
What is the slew rate of THS4042CD?
The THS4042CD has a slew rate of 400 V/µs. The Texas Instruments THS4042 datasheet identifies this as its high-speed large-signal response specification. A high slew rate helps the dual amplifier reproduce large voltage transitions rapidly, making the device appropriate for video-line drive, high-speed ADC buffering, communications, and instrumentation where slow edge rates would distort the intended waveform.
Is THS4042CD suitable for buffering high-speed ADCs?
Yes, the THS4042CD is suitable for buffering high-speed ADCs because it combines 165 MHz bandwidth, a 400 V/µs slew rate, and the ability to drive capacitive loads. According to the Texas Instruments THS4042 datasheet, buffering ADCs is a primary application for the THS4041 and THS4042 family. Place the amplifier close to the ADC input to reduce trace capacitance and preserve signal integrity.
Can THS4042CD drive a video line?
The THS4042CD can drive video lines because it provides a 165 MHz bandwidth, a 400 V/µs slew rate, and C-stable operation. The Texas Instruments THS4042 datasheet specifically identifies video-line driving as an application. Correct line impedance, termination, trace geometry, and output-current capability remain important because voltage bandwidth alone does not guarantee acceptable performance with every cable length and load.
Where can I download the THS4042CD datasheet PDF?
The official Texas Instruments THS4042 datasheet is available from the manufacturer's product-document link at https://www.ti.com/lit/gpn/THS4042. Use that document for the complete pin description, electrical characteristics, recommended operating conditions, typical performance curves, and application details. The THS4042CD is the dual SOIC order code identified on the manufacturer product page for the THS4042 family.
Where can I find the THS4042CD pinout?
The THS4042CD pinout is documented in the Texas Instruments THS4042 datasheet and the corresponding 8-SOIC package information on the manufacturer product page. The device uses an 8-SOIC (D) package with pin 1 orientation identified by the package drawing. Assign PCB nets from the manufacturer pin-description table and the package drawing rather than inferring connections from amplifier-channel order.
What is the difference between THS4041CD and THS4042CD?
The primary functional difference is channel count: THS4041CD is a single amplifier, while THS4042CD is a dual amplifier. Both belong to the Texas Instruments THS4041/THS4042 high-speed, C-stable voltage-feedback family. According to the manufacturer family description, both are designed for 165 MHz bandwidth, 400 V/µs slew rate, capacitive-load drive, and stable all-gain operation.
THS4042CD vs THS4042ID — which should be selected?
Choose THS4042CD when its specified 0°C to 70°C operating range is sufficient, and evaluate THS4042ID when the design requires the temperature grade associated with that order code. The two parts belong to the same dual high-speed amplifier family, but the suffix change can alter environmental qualification rather than core signal-path function. Confirm all electrical limits against the manufacturer ordering information before substitution.
When should I choose THS4042CD over a lower-bandwidth amplifier?
Choose THS4042CD when the signal path requires substantially more bandwidth or slew rate than a general-purpose amplifier can provide. Its 165 MHz bandwidth and 400 V/µs slew rate benefit video lines, ADC buffering, communications, and instrumentation. The trade-off is greater sensitivity to board layout and parasitic capacitance, so the high-speed design techniques described in the manufacturer datasheet should be followed.
Is THS4042CD the same as THS4042CDG4?
THS4042CD and THS4042CDG4 identify different order codes for the THS4042 dual amplifier family. The device function, 8-SOIC package, 165 MHz bandwidth, and 400 V/µs slew rate remain associated with the family, but order-code suffixes may change packing or qualification details. Compare the manufacturer ordering table before treating one as a procurement substitute for the other.
What can replace THS4042CD?
A valid replacement for THS4042CD must be a dual, pin-compatible SOIC-8 voltage-feedback amplifier with adequate bandwidth, slew rate, CMRR, supply range, output capability, and operating-temperature rating. The available family references include THS4042CDG4 and THS4042CDGN, but suffix and packing differences must be checked. No cross-brand drop-in equivalent is identified here without a verified pin-and-parameter comparison.
Is there a verified cross-brand drop-in equivalent for THS4042CD?
No verified cross-brand drop-in equivalent is identified for the THS4042CD. A valid equivalent would need the same 8-SOIC pin assignment and closely matched bandwidth, slew rate, CMRR, supply voltage, output swing, and capacitive-load behavior. Use the Texas Instruments cross-reference search or request an engineering review before choosing another manufacturer, because a similar headline bandwidth does not by itself establish pin compatibility.
Where can I buy THS4042CD and check its lead time?
Use the Request a Quote form on this page to ask about THS4042CD availability, order quantity, delivery timing, and the required package or shipment format. Current stock and lead time should be confirmed for the exact order code before committing the production schedule. Commercial availability may vary by region, quantity, and manufacturing schedule.
What is the current price of THS4042CD?
The current commercial price is obtained through the Request a Quote form on this page. The quote should identify the exact THS4042CD order code, quantity, package shipment format, and any requested traceability or inspection requirements. Requesting a formal quote also allows XAIPART to confirm current inventory and lead time for the intended production quantity.
Is THS4042CD in stock?
Current THS4042CD inventory is confirmed through the Request a Quote form on this page. Provide the required quantity, standard or nonstandard shipment format, target date, and assembly location so the response can reflect the appropriate supply plan. Do not infer availability from an individual product-page listing, because stock levels and delivery schedules change.
How should THS4042CD be laid out for high-speed performance?
Place the THS4042CD close to the source and load, keep feedback components adjacent to the amplifier, and minimize trace length on input, output, supply, and ground nets. The Texas Instruments THS4042 datasheet emphasizes stable operation with capacitive loads, but correct layout is still necessary to prevent parasitic feedback and preserve the intended 165 MHz bandwidth and 400 V/µs response.

Datos de referencia de ingeniería para THS4042CD — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose THS4042CD for a dual high-speed analog signal path requiring 165 MHz bandwidth, 400 V/µs slew rate, C-stable operation, and the ability to drive capacitive loads. It is particularly suitable for video-line drive, ADC input buffering, communications conditioning, and instrumentation front ends. Verify the complete electrical limits against the manufacturer datasheet, especially supply voltage, input and output swing, output current, noise, offset, and operating temperature. The single-channel THS4041CD may be preferable when only one amplifier is required, but it is not a pin-compatible substitute for the dual device. THS4042CDG4 and THS4042CDGN belong to the same family, yet their order codes may differ in packing or qualification attributes and must be checked before use as procurement alternatives. No cross-brand drop-in equivalent should be selected solely from bandwidth and slew-rate similarity; pin assignment and the remaining electrical parameters must match.

Comparación con alternativas

Parámetro Este producto
Amplifier Type Dual voltage-feedback operational amplifier
Number of Channels 2 channels
Gain-Bandwidth Product 165 MHz
Slew Rate 400 V/µs
Common-Mode Rejection Ratio 80 dB
Compensation C-stable
Closed-Loop Gain Support All gains in inverting and noninverting configurations
Package 8-SOIC (D)
Brand Texas Instruments
Operating Temperature Range 0°C to 70°C

Diferenciadores clave

  • Two high-speed channels in one device (frente a THS4041CD)
  • C-stable operation across closed-loop gains (frente a THS4042CDG4)
  • High-speed performance with capacitive-load drive (frente a THS4042CDGN)

Notas de diseño

Place the THS4042CD adjacent to the driven load and minimize the distance from its output pin to the receiving circuit. Keep the feedback loop compact and route it away from input and output nets to prevent parasitic feedback. A continuous ground plane and short ground-return paths are preferable to long traces through or above the device. High-frequency performance depends on the physical implementation as much as the nominal 165 MHz bandwidth.

Do not treat the C-stable rating as permission to ignore loading. The amplifier can drive capacitive loads, but excessive cable, probe, connector, or ADC-input capacitance can still create ringing, overshoot, and bandwidth loss. Keep capacitance close to the device when possible, use series damping when required by the system, and validate the complete connection with oscilloscope measurements using short, low-inductance test connections.

Place each supply decoupling capacitor directly beside its corresponding power and ground pins and use the shortest possible current loop. Follow the manufacturer datasheet for the recommended capacitor values and supply arrangement. Because a 400 V/µs slew rate can produce fast output transitions, inadequate high-frequency supply impedance may couple into the output or disturb other analog circuits sharing the same supply network.

Choose external feedback and gain-setting resistors with values that preserve the intended bandwidth while limiting parasitic capacitance at the summing node. Avoid excessively large resistor values at high gain, and avoid extremely small values that increase amplifier output-current demand and power dissipation. Confirm closed-loop stability, output swing, and settling behavior using the exact gain and load configuration planned for the finished board.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The available product information identifies an 8-SOIC commercial-temperature order code but does not provide explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations for this exact MPN. AEC-Q100 qualification is not indicated and is therefore recorded as not applicable.

Datos verificados el: 2026-11-10 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

THS4042CD THS4042CD datasheet THS4042CD datasheet pdf THS4042CD pinout THS4042CD specifications THS4042CD equivalent THS4042CD replacement THS4042CD drop-in replacement THS4042CD price THS4042CD stock Texas Instruments THS4042CD THS4042 165MHz dual amplifier THS4042 8-SOIC pinout THS4042 video line driver THS4042 vs THS4041

Componentes & términos relacionados

Texas Instruments THS4042CD THS4042 THS4041CD THS4042CDG4 THS4042CDGN voltage-feedback operational amplifier high-speed operational amplifier dual amplifier analog IC semiconductor C-stable gain-bandwidth product slew rate common-mode rejection ratio CMRR ADC input buffering video-line driving communications signal conditioning capacitive-load drive 8-SOIC SOIC family surface-mount package inverting configuration noninverting configuration
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ