TLV2451IP - 6V, 220kHz RRIO Low-Power Op Amp | Texas Instruments
N.º de pieza: TLV2451IP ✓ ActivoTLV2451IP Descripción general
An operational amplifier is a voltage-controlled, high-gain analog building block used to amplify, filter, buffer, compare, and drive signals. The TLV2451 belongs to the linear operational-amplifier family within the broader voltage-amplifier and analog IC hierarchy. Rail-to-rail input capability allows the amplifier to operate near the positive and negative supply limits, while rail-to-rail output operation permits the output voltage to approach the supply rails under suitable load conditions.
The principal features of the TLV2451IP are its 6 V maximum supply rating, 23 µA quiescent current, 220 kHz gain-bandwidth product, and single-amplifier configuration. Its low quiescent current reduces the supply demand of continuously powered circuits, while 220 kHz of bandwidth provides useful dynamic performance for low-frequency sensing, filtering, and control tasks. The PDIP format also supports conventional through-hole insertion, lead inspection, and straightforward prototyping.
Technically, the TLV2451 combines a micropower operating point with rail-to-rail input and output stages. This balance is valuable when signals must be sensed close to the supply rails but the application cannot tolerate the higher supply current of many conventional rail-to-rail amplifiers. Because the device is intended for low-voltage operation, its supply voltage and input common-mode range must be checked against the actual circuit. Exact offset, drift, output-current, noise, and stability limits should be confirmed in the manufacturer datasheet before a precision or capacitive-load design is released.
Typical applications include low-power sensor conditioning, portable medical instrumentation, industrial process measurement, battery-operated data acquisition, audio and communication interfaces, and general-purpose analog control loops. In these systems, the TLV2451IP can provide input buffering, gain amplification, active filtering, threshold detection, or low-frequency drive without requiring a high-bandwidth, high-current amplifier.
A key design consideration is stability with capacitive loading. The input and output network should follow the manufacturer datasheet guidance, especially when driving long PCB traces, ADC sample-and-hold inputs, multiplexers, or significant cable capacitance. Decoupling close to the supply pins, a suitable output isolation resistor, and a verified phase-margin margin are important for reliable low-power analog performance.
This page combines the TLV2451IP manufacturer specifications, verified sourcing information, same-family drop-in alternatives, pin assignment guidance, application-oriented engineering notes, and parameter-by-parameter comparison data. It is designed to support component selection, PCB compatibility checks, and first-pass circuit planning without replacing the manufacturer datasheet for production release.
Alternativas directas para TLV2451IP — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
TLV2451CP
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
TLV2451CPE4
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
TLV2451IP Valores máximos y características eléctricas
| Amplifier Type | Single operational amplifier |
| Maximum Supply Voltage | 6 V |
| Corriente en reposo | 23 µA |
| Gain-Bandwidth Product | 220 kHz |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Channel Count | 1 channel |
| Encapsulado | 8-pin PDIP |
| Tipo de montaje | Through-hole |
| Product Classification | General-purpose amplifier |
Configuración de pines de TLV2451IP
| Pin 1 | NC — Not connected |
| Pin 2 | IN- — Inverting input |
| Pin 3 | IN+ — Non-inverting input |
| Pin 4 | V- — Negative supply voltage |
| Pin 5 | NC — Not connected |
| Pin 6 | OUT — Output |
| Pin 7 | V+ — Positive supply voltage |
| Pin 8 | NC — Not connected |
Aplicaciones típicas
TLV2451IP es adecuado para 6 aplicacións: Battery-Powered Sensor Signal Conditioning, Portable Medical Monitoring, Industrial Process Measurement, Low-Power Data Acquisition, Audio and Communication Interface, Precision Threshold and Control Loops.
Battery-Powered Sensor Signal Conditioning
The TLV2451IP fits low-power sensor front ends because its 23 µA quiescent current limits standing supply demand while its rail-to-rail input stage accepts signals operating close to the supply rails. It can buffer a bridge, resistive, or current-based sensor before amplification or conversion by an ADC. The 220 kHz gain-bandwidth product is suitable for low-frequency measurement signals rather than wideband instrumentation. Confirm the sensor's common-mode range, the amplifier's exact offset and drift limits, and the total current drawn by the complete analog chain before finalizing the power budget.
Recomendado
Portable Medical Monitoring
The TLV2451IP is useful in portable monitoring modules where each amplifier contributes directly to battery life. Its 23 µA quiescent current is attractive for low-level physiological or diagnostic sensor conditioning, while rail-to-rail input and output operation helps use a restricted supply range efficiently. The 220 kHz bandwidth supports modest-bandwidth filtering and buffering. A medical design must still verify noise, offset, drift, common-mode behavior, and isolation requirements from the manufacturer datasheet rather than treating general-purpose performance as sufficient for every clinical measurement chain.
Recomendado
Industrial Process Measurement
The TLV2451IP can condition slow industrial sensor signals in compact control and monitoring equipment. Its 6 V maximum supply rating supports low-voltage process interfaces, and the single-amplifier 8-pin PDIP package simplifies through-hole construction and maintenance. Rail-to-rail operation helps preserve signal range in systems whose transducer output moves close to either supply rail. The 220 kHz gain-bandwidth product is adequate for many temperature, pressure, and level signals, but designers should verify input impedance, offset behavior, noise, and long-cable noise pickup for the installed sensor system.
Recomendado
Low-Power Data Acquisition
The TLV2451IP fits multiplexed, low-speed data-acquisition systems where channel settling, input buffering, and supply efficiency matter. Its 220 kHz gain-bandwidth product can amplify sensor-level signals within a compact measurement front end, while the 23 µA quiescent current helps control the penalty of keeping the amplifier continuously powered. Rail-to-rail inputs are valuable when the ADC or sensor uses nearly the full available voltage range. Validate settling against the actual multiplexer resistance, sampling rate, ADC acquisition window, and source impedance before choosing gain and filtering values.
Recomendado
Audio and Communication Interface
The TLV2451IP can perform low-level buffering or gain stages in portable audio and communication interfaces when the signal bandwidth remains modest. Rail-to-rail input and output operation helps accommodate signals generated from a low-voltage supply, and the 23 µA quiescent current supports portable operation. The 220 kHz gain-bandwidth product is suitable for low-frequency control, microphone-bias buffering, or baseband conditioning rather than high-fidelity audio output stages. Check the required output swing, capacitive-load stability, noise performance, and channel-to-channel matching in the target operating point.
Recomendado
Precision Threshold and Control Loops
The TLV2451IP is appropriate for low-frequency threshold detection, comparator-like control, and small closed-loop analog systems powered from a 6 V-class rail. The 23 µA quiescent current reduces overhead in continuously monitored equipment, while the 220 kHz gain-bandwidth product provides more bandwidth than many similarly low-power amplifiers. Rail-to-rail output behavior can increase usable control range. For servo loops or precision threshold circuits, verify open-loop gain, phase margin, output-current capability, and the datasheet's stability recommendations under the actual feedback network.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para TLV2451IP — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | TLV2451CP | TLV2451CPE4 |
|---|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Count | 1 channel | 1 channel | 1 channel |
| Maximum Supply Voltage | 6 V | 6 V | 6 V |
| Quiescent Current | 23 µA | 23 µA | 23 µA |
| Gain-Bandwidth Product | 220 kHz | 220 kHz | 220 kHz |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Mounting Type | Through-hole | Through-hole | Through-hole |
| Primary Compared Parameters | Reference device | 0% measurable difference reported | 0% measurable difference reported |
Diferenciadores clave
- Same-footprint replacement with no reported primary performance difference (frente a TLV2451CP)
- Low-power operation without sacrificing rail-to-rail signal handling (frente a TLV2451CPE4)
- Single-amplifier simplicity for low-voltage through-hole designs (frente a TLV2451CP)
Notas de diseño
Account for both the 23 µA quiescent current and the additional supply current demanded by the output stage under load. The manufacturer's TLV2451 datasheet should be used to select the final operating point, especially when driving a resistive load or operating close to the output-current limit. For a battery design, include leakage from external resistors, protection devices, ADC channels, and the sensor because the amplifier's quiescent current alone does not determine total system consumption.
Do not assume that every low-power rail-to-rail amplifier can drive the intended load. Check the TLV2451 output-current capability, output-voltage limits, and capacitive-load stability from the manufacturer datasheet. Add a series isolation resistor when driving ADC inputs, multiplexers, long traces, or cables, and then verify settling and oscillation margin using the final source and load impedances.
Place the supply bypass capacitor close to pins 7 and 4, and keep the input and output paths short to reduce parasitic pickup and feedback. The 8-pin PDIP footprint provides generous spacing for through-hole assembly, but long loops around the amplifier can couple adjacent-channel signals into a high-impedance sensor node. Maintain a practical ground return and avoid routing sensitive input traces parallel to switching-conductor paths.
Información de cumplimiento
The available manufacturer and distributor information does not provide explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals statements for the exact TLV2451IP ordering suffix. The device is a general-purpose operational amplifier rather than an automotive-qualified variant.