TLV2623IN - 11MHz Dual Rail-to-Rail Op Amp | Texas Instruments
N.º de pieza: TLV2623IN ✓ ActivoTLV2623IN Descripción general
A rail-to-rail operational amplifier is a voltage-feedback amplifier whose output can swing close to either supply rail. It belongs to the operational amplifier hierarchy within analog ICs and broader semiconductor signal-processing devices. The TLV2623 family is intended for single-supply systems where low-power operation, wide bandwidth, and output swing are more important than bipolar input bias currents. Its shutdown function allows a powered-down state when the circuit does not need to remain active.
The TLV2623IN combines an 11 MHz gain-bandwidth product with rail-to-rail output operation and a maximum supply rating of 5.5 V. The verified product information identifies approximately 800 uA of supply current per channel, a typical input offset voltage of 250 uV, and a maximum input offset voltage of 4500 uV. These characteristics suit precision signal conditioning, low-side current measurement, sensor interfaces, and general-purpose analog signal paths.
Internally, the amplifier combines CMOS input and output stages with frequency compensation that supports high closed-loop bandwidth at low gain. The rail-to-rail output stage improves usable output range in 3.3 V and 5 V systems, while the shutdown control can reduce system activity when measurements or signal processing are not required. Because the family is intended for low-power, wide-bandwidth single-supply operation, external decoupling and careful output-load selection remain important.
Typical uses include bridge and thermistor sensor interfaces, buffered analog control signals, low-side current sensing with amplification, instrumentation signal conditioning, and embedded test circuits. The 11 MHz bandwidth can support higher-frequency feedback networks than a general-purpose micropower amplifier, provided that stability, noise, and output drive are evaluated for the selected gain and load.
For layout, place the supply bypass capacitor close to the device power pins and keep feedback components close to the amplifier inputs and output. Avoid long high-impedance traces because they can increase noise pickup and coupling. Confirm the absolute maximum supply rating, common-mode range, output swing, and shutdown logic levels against the manufacturer datasheet before finalizing the circuit.
This page combines the manufacturer product information with engineering guidance, application analysis, package details, and carefully qualified replacement options. The accompanying comparison and design notes help engineers assess fit, signal bandwidth, power behavior, and board-level implementation before selecting the amplifier.
Alternativas directas para TLV2623IN — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
TLV2624IN
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
TLV2622IN
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
TLV2623IN Valores máximos y características eléctricas
| Amplifier Type | CMOS operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 11 MHz |
| Maximum Supply Voltage | 5.5 V |
| Nominal Supply Voltage | ±2.75 V or 5.5 V |
| Tipo de salida | Rail-to-rail |
| Shutdown Capability | Enabled |
| Supply Current per Channel | 800 uA |
| Typical Input Offset Voltage | 250 uV |
| Maximum Input Offset Voltage | 4500 uV |
| Rango de temperatura de funcionamiento | -40 C to +125 C |
| Package Type | 14-pin PDIP |
| Package Pitch | 7.62 mm |
| Tipo de montaje | Through-hole |
Guía de configuración de pines de TLV2623IN 7.62 mm
Configuración de pines para TLV2623IN (encapsulado 7.62 mm). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para TLV2623IN.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
TLV2623IN es adecuado para 6 aplicacións: Low-Side Current Sensing, Bridge Sensor Signal Conditioning, Thermistor and Resistive Sensor Front Ends, General-Purpose Analog Signal Buffering, Portable Instrumentation, Industrial Control Signal Interface.
Low-Side Current Sensing
The TLV2623IN suits low-side current measurement because its dual CMOS channels can amplify the small voltage generated across a low-value shunt while an 11 MHz gain-bandwidth product preserves useful response above DC. Rail-to-rail output operation provides more signal range in a 3.3 V or 5 V supply system, while the approximately 800 uA per-channel supply current limits the amplifier's own contribution to power consumption. One channel can amplify the shunt signal and the other can provide gain or level conditioning. The design must account for shunt common-mode voltage, amplifier input offset voltage of 250 uV typical, resistor tolerance, and the closed-loop stability appropriate to the selected gain.
Recomendado
Bridge Sensor Signal Conditioning
The TLV2623IN is suitable for conditioning resistive bridge outputs where millivolt-level differential signals must be amplified into a more useful logic or measurement range. Its 11 MHz gain-bandwidth product provides more closed-loop bandwidth than typical low-frequency micropower op amps, while rail-to-rail output operation helps utilize the available supply voltage. The dual-channel arrangement can amplify the bridge output and provide additional filtering, buffering, or reference conditioning. Input bias current, common-mode range, and noise must be checked against the bridge impedance. Keeping feedback resistors close to the amplifier pins and routing the bridge pair as a tightly coupled differential pair helps reduce conversion error and interference pickup.
Recomendado
Thermistor and Resistive Sensor Front Ends
The TLV2623IN can condition resistive sensor signals in compact industrial or embedded measurement systems. Its approximately 800 uA supply current per channel is useful where sensor circuitry must operate from a constrained 3.3 V or 5 V rail, and the rail-to-rail output stage can drive an ADC input more effectively than a fixed-range amplifier. One channel may buffer a thermistor divider while the other amplifies or offsets the resulting voltage. Accuracy depends on input offset voltage, bias current, resistor matching, ADC input range, and self-heating in the sensor network. The 11 MHz bandwidth is more than adequate for many thermal measurement loops while still allowing noise filtering.
Recomendado
General-Purpose Analog Signal Buffering
The TLV2623IN provides two independent rail-to-rail output amplifiers for buffering higher-impedance analog sources before ADC sampling, comparison, or downstream filtering. Its 11 MHz gain-bandwidth product can accommodate signal paths that would be bandwidth-limited by very low-frequency micropower amplifiers, while its approximately 800 uA per-channel supply current preserves a reasonable efficiency balance. The CMOS implementation is especially appropriate in battery-powered instrumentation when the source is not extremely high impedance. Evaluate capacitive loading at the output, configure noise gain for stability, and verify that the source voltage remains inside the input common-mode range during startup and shutdown transitions.
Recomendado
Portable Instrumentation
The TLV2623IN fits handheld and portable instrumentation that combines measurement accuracy with limited supply capacity. Two amplifier channels, approximately 800 uA per channel, and a maximum 5.5 V supply rating support compact, single-supply designs. The 11 MHz bandwidth provides flexibility for filtering, active gain stages, and faster signal transitions than a conventional micropower amplifier. Low power is obtained by also using the device's shutdown function when measurements are intermittent rather than relying solely on the already-low channel supply current. Designers should verify startup behavior, ADC settling time, injected noise, and the effect of external resistor networks on the total portable-system power budget.
Recomendado
Industrial Control Signal Interface
The TLV2623IN can buffer and condition low-level analog control signals in industrial control equipment while operating from a 3.3 V or 5 V rail. The dual-channel configuration reduces the number of packages needed for related signal paths, and the 11 MHz bandwidth is useful where filtered analog signals must transition rapidly into control or monitoring circuitry. Rail-to-rail output operation increases usable signal swing, although the output must remain within its rated swing under the connected load. Industrial implementations should also assess temperature range, electromagnetic coupling, input protection, and stability with capacitive cable loads. The verified operating range of -40 C to +125 C supports applications across wide ambient conditions.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para TLV2623IN — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | TLV2624IN | TLV2622IN |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-PDIP | 14-PDIP | 14-PDIP |
| Amplifier Channels | 2 | 2 | 2 |
| Mounting Type | Through-hole | Through-hole | Through-hole |
Diferenciadores clave
- Higher specified bandwidth than the lower-bandwidth family alternative (frente a TLV2622IN)
- Lower bandwidth than the faster family alternative (frente a TLV2624IN)
- Dual-channel integration in a through-hole package (frente a Single-amplifier alternatives)
Notas de diseño
Place the supply bypass capacitor immediately beside the TLV2623 power and ground pins, with the ground return forming a short path to the capacitor. The device consumes approximately 800 uA per channel, but external feedback and bias networks can add appreciable current in high-impedance circuits. Use the shutdown function when the signal path can be disabled, and confirm the control thresholds and state-specific supply current against the manufacturer datasheet.
Keep the two amplifier inputs, feedback resistors, and any compensation components close together and away from switching nodes. An 11 MHz gain-bandwidth product can respond to unwanted high-frequency energy even when the intended signal is slow. For long sensor leads, terminate inputs close to the source or use guarded, tightly coupled routing. Check noise gain and phase margin for the selected closed-loop gain and output capacitance.
Do not treat rail-to-rail output as rail-to-rail input. The verified product information confirms rail-to-rail output operation, but the input common-mode range must still be checked for every sensor, divider, and ADC interface. Also distinguish the 250 uV typical input offset voltage from the 4500 uV maximum limit. Use worst-case offset and resistor tolerances when setting an accuracy target.
Route differential sensor inputs as a pair and maintain consistent geometry to reduce differential noise pickup and gain from unequal impedances. Place input and feedback components on the same side of the board where practical and avoid routing them beneath digital clock or switching-regulator areas. For the 14-pin PDIP footprint, preserve adequate spacing around adjacent pins and check component orientation against the manufacturer's pin table before assembly.
Información de cumplimiento
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified in the manufacturer or distributor information. Confirm compliance for the exact production lot with Texas Instruments.