Texas Instruments

TLV2623IN - 11MHz Dual Rail-to-Rail Op Amp | Texas Instruments

부품 번호: TLV2623IN ✓ 활성
5.5 V Vdss 800 uA Id 14-pin PDIP Package
MOQ: 1 |

TLV2623IN 개요

Texas Instruments TLV2623IN is a dual, low-power, rail-to-rail output CMOS operational amplifier with an 11 MHz gain-bandwidth product, 5.5 V maximum supply voltage, and shutdown capability. The device is supplied in a 14-pin PDIP package for through-hole industrial, instrumentation, and embedded signal-conditioning applications. Its low-power architecture, approximately 800 uA per channel supply current, and 11 MHz bandwidth provide a useful balance between signal speed, energy use, and circuit complexity.

A rail-to-rail operational amplifier is a voltage-feedback amplifier whose output can swing close to either supply rail. It belongs to the operational amplifier hierarchy within analog ICs and broader semiconductor signal-processing devices. The TLV2623 family is intended for single-supply systems where low-power operation, wide bandwidth, and output swing are more important than bipolar input bias currents. Its shutdown function allows a powered-down state when the circuit does not need to remain active.

The TLV2623IN combines an 11 MHz gain-bandwidth product with rail-to-rail output operation and a maximum supply rating of 5.5 V. The verified product information identifies approximately 800 uA of supply current per channel, a typical input offset voltage of 250 uV, and a maximum input offset voltage of 4500 uV. These characteristics suit precision signal conditioning, low-side current measurement, sensor interfaces, and general-purpose analog signal paths.

Internally, the amplifier combines CMOS input and output stages with frequency compensation that supports high closed-loop bandwidth at low gain. The rail-to-rail output stage improves usable output range in 3.3 V and 5 V systems, while the shutdown control can reduce system activity when measurements or signal processing are not required. Because the family is intended for low-power, wide-bandwidth single-supply operation, external decoupling and careful output-load selection remain important.

Typical uses include bridge and thermistor sensor interfaces, buffered analog control signals, low-side current sensing with amplification, instrumentation signal conditioning, and embedded test circuits. The 11 MHz bandwidth can support higher-frequency feedback networks than a general-purpose micropower amplifier, provided that stability, noise, and output drive are evaluated for the selected gain and load.

For layout, place the supply bypass capacitor close to the device power pins and keep feedback components close to the amplifier inputs and output. Avoid long high-impedance traces because they can increase noise pickup and coupling. Confirm the absolute maximum supply rating, common-mode range, output swing, and shutdown logic levels against the manufacturer datasheet before finalizing the circuit.

This page combines the manufacturer product information with engineering guidance, application analysis, package details, and carefully qualified replacement options. The accompanying comparison and design notes help engineers assess fit, signal bandwidth, power behavior, and board-level implementation before selecting the amplifier.

드롭인 대체품: TLV2623IN — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

TLV2624IN

✅ 드롭인 ⚠️ 사양 미검증
📦 14-PDIP
Same 14-pin PDIP family and dual-amplifier architecture, but the TLV2624 has a higher bandwidth profile than the TLV2623's 11 MHz rating.

📋 참조 대체품 (카탈로그에 없음)

TLV2622IN

✅ 드롭인 ⚠️ 사양 미검증
📦 14-PDIP
Same 14-pin PDIP family and dual-amplifier architecture, but the TLV2622 has a lower bandwidth profile than the TLV2623's 11 MHz rating.

📋 참조 대체품 (카탈로그에 없음)

TLV2623IN 최대 정격 & 전기적 특성

Amplifier Type CMOS operational amplifier
Number of Channels 2 channels
Gain-Bandwidth Product 11 MHz
Maximum Supply Voltage 5.5 V
Nominal Supply Voltage ±2.75 V or 5.5 V
출력 유형 Rail-to-rail
Shutdown Capability Enabled
Supply Current per Channel 800 uA
Typical Input Offset Voltage 250 uV
Maximum Input Offset Voltage 4500 uV
동작 온도 범위 -40 C to +125 C
Package Type 14-pin PDIP
Package Pitch 7.62 mm
실장 유형 Through-hole

TLV2623IN 7.62 mm 핀 구성 가이드

TLV2623IN(7.62 mm 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.

TLV2623IN의 7.62 mm 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: TLV2623IN.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

TLV2623IN 적합 용도: 6 애플리케이션s: Low-Side Current Sensing, Bridge Sensor Signal Conditioning, Thermistor and Resistive Sensor Front Ends, General-Purpose Analog Signal Buffering, Portable Instrumentation, Industrial Control Signal Interface.

⚡

Low-Side Current Sensing

The TLV2623IN suits low-side current measurement because its dual CMOS channels can amplify the small voltage generated across a low-value shunt while an 11 MHz gain-bandwidth product preserves useful response above DC. Rail-to-rail output operation provides more signal range in a 3.3 V or 5 V supply system, while the approximately 800 uA per-channel supply current limits the amplifier's own contribution to power consumption. One channel can amplify the shunt signal and the other can provide gain or level conditioning. The design must account for shunt common-mode voltage, amplifier input offset voltage of 250 uV typical, resistor tolerance, and the closed-loop stability appropriate to the selected gain.

🏭

Bridge Sensor Signal Conditioning

The TLV2623IN is suitable for conditioning resistive bridge outputs where millivolt-level differential signals must be amplified into a more useful logic or measurement range. Its 11 MHz gain-bandwidth product provides more closed-loop bandwidth than typical low-frequency micropower op amps, while rail-to-rail output operation helps utilize the available supply voltage. The dual-channel arrangement can amplify the bridge output and provide additional filtering, buffering, or reference conditioning. Input bias current, common-mode range, and noise must be checked against the bridge impedance. Keeping feedback resistors close to the amplifier pins and routing the bridge pair as a tightly coupled differential pair helps reduce conversion error and interference pickup.

🌡️

Thermistor and Resistive Sensor Front Ends

The TLV2623IN can condition resistive sensor signals in compact industrial or embedded measurement systems. Its approximately 800 uA supply current per channel is useful where sensor circuitry must operate from a constrained 3.3 V or 5 V rail, and the rail-to-rail output stage can drive an ADC input more effectively than a fixed-range amplifier. One channel may buffer a thermistor divider while the other amplifies or offsets the resulting voltage. Accuracy depends on input offset voltage, bias current, resistor matching, ADC input range, and self-heating in the sensor network. The 11 MHz bandwidth is more than adequate for many thermal measurement loops while still allowing noise filtering.

🔧

General-Purpose Analog Signal Buffering

The TLV2623IN provides two independent rail-to-rail output amplifiers for buffering higher-impedance analog sources before ADC sampling, comparison, or downstream filtering. Its 11 MHz gain-bandwidth product can accommodate signal paths that would be bandwidth-limited by very low-frequency micropower amplifiers, while its approximately 800 uA per-channel supply current preserves a reasonable efficiency balance. The CMOS implementation is especially appropriate in battery-powered instrumentation when the source is not extremely high impedance. Evaluate capacitive loading at the output, configure noise gain for stability, and verify that the source voltage remains inside the input common-mode range during startup and shutdown transitions.

📱

Portable Instrumentation

The TLV2623IN fits handheld and portable instrumentation that combines measurement accuracy with limited supply capacity. Two amplifier channels, approximately 800 uA per channel, and a maximum 5.5 V supply rating support compact, single-supply designs. The 11 MHz bandwidth provides flexibility for filtering, active gain stages, and faster signal transitions than a conventional micropower amplifier. Low power is obtained by also using the device's shutdown function when measurements are intermittent rather than relying solely on the already-low channel supply current. Designers should verify startup behavior, ADC settling time, injected noise, and the effect of external resistor networks on the total portable-system power budget.

🏭

Industrial Control Signal Interface

The TLV2623IN can buffer and condition low-level analog control signals in industrial control equipment while operating from a 3.3 V or 5 V rail. The dual-channel configuration reduces the number of packages needed for related signal paths, and the 11 MHz bandwidth is useful where filtered analog signals must transition rapidly into control or monitoring circuitry. Rail-to-rail output operation increases usable signal swing, although the output must remain within its rated swing under the connected load. Industrial implementations should also assess temperature range, electromagnetic coupling, input protection, and stability with capacitive cable loads. The verified operating range of -40 C to +125 C supports applications across wide ambient conditions.

What are the key specifications of TLV2623IN that engineers should know?
The TLV2623IN is a dual CMOS operational amplifier with an 11 MHz gain-bandwidth product, 5.5 V maximum supply voltage, rail-to-rail output, shutdown capability, and a 14-pin PDIP package. According to the Texas Instruments TLV2623 family datasheet, it combines low-power operation with approximately 800 uA supply current per channel, making it suitable for general-purpose analog signal conditioning.
What is the operating voltage of TLV2623IN?
The TLV2623IN supports a maximum supply voltage of 5.5 V and is identified for single-supply operation around 5.5 V or dual-supply operation around ±2.75 V. According to the Texas Instruments TLV2623 family datasheet, the exact common-mode input range must remain inside the device's specified operating limits, so supply voltage and signal amplitude should be checked together.
Where can I download the TLV2623IN datasheet PDF?
The official TLV2623IN datasheet is available from Texas Instruments through the TLV2623 product support page and the manufacturer datasheet link on this page. The document covers the TLV2623 family, including electrical characteristics, shutdown operation, pin configuration, and application guidance. Use the manufacturer PDF for the complete rated limits and test conditions.
Where can I find the TLV2623IN pinout?
The TLV2623IN uses a 14-pin PDIP package, and its numbered pin configuration and descriptions are shown in the Texas Instruments TLV2623 family datasheet. Use that pin-description table when assigning amplifier inputs, outputs, supply pins, and shutdown-control pins. The package drawing on this page shows the physical 14-pin outline rather than replacing the manufacturer pin table.
What can replace TLV2623IN?
The closest qualified replacement is the same-package TLV2623 family option listed as an alternative on this page, subject to its channel-specific bandwidth and shutdown differences. A true drop-in replacement must use the same 14-pin PDIP footprint and preserve the required power, shutdown, common-mode, and output-swing behavior. Confirm the complete datasheet and pin function before approving any substitution.
Is TLV2623IN the same as TLV2624IN?
No. The TLV2623IN and TLV2624IN are members of the same low-power operational-amplifier family, but their bandwidth and channel-specific performance differ. The TLV2623 is specified at 11 MHz, while the TLV2624 option has a different bandwidth profile. The listed match percentage reflects only the degree of parameter similarity and still requires pin-function and application-level verification.
When should I choose TLV2623IN over a lower-bandwidth dual op amp?
Choose the TLV2623IN when a 3.3 V or 5 V system needs more than general-purpose low-frequency amplification and benefits from an 11 MHz gain-bandwidth product. Its dual channel count also consolidates two amplifier functions in one package. If the signal path is limited to slow sensor signals, a lower-bandwidth micropower amplifier may provide a better power-consumption match.
Is TLV2623IN suitable for sensor signal conditioning?
Yes. The TLV2623IN is well suited to sensor interfaces because it provides two amplifiers, an 11 MHz gain-bandwidth product, approximately 800 uA supply current per channel, and rail-to-rail output operation. Its typical input offset voltage of 250 uV is appropriate for many bridge, thermistor, and general analog sensor stages, although the input bias and common-mode requirements must match the sensor.
How much power does TLV2623IN consume?
The TLV2623IN consumes approximately 800 uA per channel under the manufacturer operating conditions, or about 1.6 mA for both channels at 5.5 V before shutdown-state effects are considered. The resulting total supply power at 5.5 V is approximately 8.8 mA for both channels. Actual equipment consumption also includes external divider and feedback-network current.
What is the best Texas Instruments equivalent for TLV2623IN?
The closest same-family choice is the TLV2624IN when a 14-pin PDIP dual amplifier can meet the circuit's bandwidth requirements, because both devices use the same through-hole package family and belong to the TI low-power, wide-bandwidth shutdown-enabled family. The TLV2624 has a different bandwidth profile, so it should be selected only after checking signal bandwidth, stability, and output-drive requirements.
Where can I buy TLV2623IN online?
Use the Request a Quote form on this page to request TLV2623IN availability, order quantities, and current lead time from XAIPART. The request identifies the exact TLV2623IN ordering code and its 14-pin PDIP package, helping prevent accidental substitution with the surface-mount TLV2623IDGSR or other TLV2623 package options.
What is the price of TLV2623IN?
Current TLV2623IN pricing is presented through the Request a Quote form on this page rather than in fixed prose, because commercial terms and quantities can change. Submit the required quantity and target package information in the form to receive a current quotation for the exact TLV2623IN MPN. The structured listing information on this page is retained for purchasing-system reference.
What is the lead time and stock status for TLV2623IN?
Request the current TLV2623IN stock position, minimum order quantity, and production lead time through the Request a Quote form on this page. The exact package code matters because TLV2623 is also offered in surface-mount configurations. XAIPART will confirm availability and scheduling against the 14-pin PDIP ordering code before accepting a production order.
TLV2623IN vs TLV2622IN: which is better for a fast analog signal?
The TLV2623IN is generally preferable when a fast analog signal requires the family's higher 11 MHz bandwidth and the signal can be closed-loop stabilized at the intended gain. The TLV2622IN offers a different bandwidth profile and may be sufficient for lower-frequency conditioning. Final selection depends on the required gain, phase margin, output load, and complete electrical limits.
Does the TLV2623IN include shutdown control?
Yes. The Texas Instruments TLV2623 family is identified as a shutdown-enabled operational amplifier family, and the TLV2623IN uses that dual-amplifier implementation. Shutdown can place the amplifier in a low-power state when signal processing is not required. Use the manufacturer's logic-level and timing information to design the control signal and ensure every shutdown state is compatible with downstream circuitry.

엔지니어링 참조 데이터: TLV2623IN — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose TLV2623IN for compact 3.3 V or 5 V analog designs that need two rail-to-rail output channels, an 11 MHz gain-bandwidth product, and approximately 800 uA supply current per channel. It is especially useful for sensor interfaces, low-side current measurement, signal buffering, and instrumentation where a conventional micropower amplifier would provide too little bandwidth. Select TLV2624IN when the circuit requires the faster bandwidth profile of that family member and its other electrical characteristics satisfy the design. Select TLV2622IN when its lower bandwidth is sufficient and its overall power, offset, noise, and stability characteristics better match the application. In every case, verify the complete manufacturer electrical table, shutdown logic, common-mode range, output swing, and stability with the intended load before approving a substitution.

대체품과의 비교

파라미터 이 제품 TLV2624IN TLV2622IN
Brand Texas Instruments Texas Instruments Texas Instruments
Package 14-PDIP 14-PDIP 14-PDIP
Amplifier Channels 2 2 2
Mounting Type Through-hole Through-hole Through-hole

주요 차별점

  • Higher specified bandwidth than the lower-bandwidth family alternative (vs TLV2622IN)
  • Lower bandwidth than the faster family alternative (vs TLV2624IN)
  • Dual-channel integration in a through-hole package (vs Single-amplifier alternatives)

설계 노트

Place the supply bypass capacitor immediately beside the TLV2623 power and ground pins, with the ground return forming a short path to the capacitor. The device consumes approximately 800 uA per channel, but external feedback and bias networks can add appreciable current in high-impedance circuits. Use the shutdown function when the signal path can be disabled, and confirm the control thresholds and state-specific supply current against the manufacturer datasheet.

Keep the two amplifier inputs, feedback resistors, and any compensation components close together and away from switching nodes. An 11 MHz gain-bandwidth product can respond to unwanted high-frequency energy even when the intended signal is slow. For long sensor leads, terminate inputs close to the source or use guarded, tightly coupled routing. Check noise gain and phase margin for the selected closed-loop gain and output capacitance.

Do not treat rail-to-rail output as rail-to-rail input. The verified product information confirms rail-to-rail output operation, but the input common-mode range must still be checked for every sensor, divider, and ADC interface. Also distinguish the 250 uV typical input offset voltage from the 4500 uV maximum limit. Use worst-case offset and resistor tolerances when setting an accuracy target.

Route differential sensor inputs as a pair and maintain consistent geometry to reduce differential noise pickup and gain from unequal impedances. Place input and feedback components on the same side of the board where practical and avoid routing them beneath digital clock or switching-regulator areas. For the 14-pin PDIP footprint, preserve adequate spacing around adjacent pins and check component orientation against the manufacturer's pin table before assembly.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified in the manufacturer or distributor information. Confirm compliance for the exact production lot with Texas Instruments.

데이터 검증일: 2026-11-19 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

TLV2623IN datasheet TLV2623IN datasheet pdf TLV2623IN pinout TLV2623IN 14-PDIP TLV2623IN equivalent TLV2623IN replacement TLV2623IN cross reference TLV2623IN vs TLV2624IN Texas Instruments TLV2623IN TLV2623IN 11MHz op amp TLV2623IN application circuit TLV2623IN price TLV2623IN stock TLV2623IN buy online TLV2623IN shutdown pin

관련 부품 & 용어

Texas Instruments TLV2623IN TLV2623 TLV2624IN TLV2622IN TLV2623IDGSR OPA828ID operational amplifier dual amplifier rail-to-rail output CMOS gain-bandwidth product shutdown input offset voltage common-mode voltage range signal conditioning low-side current sensing bridge sensor thermistor industrial instrumentation 14-PDIP DIP through-hole package low-power analog IC semiconductor
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기