STMicroelectronics

TS3702CN - 9µA Dual CMOS Comparator | STMicroelectronics

N.º de pieza: TS3702CN ✓ Activo
9 µA typical Vdss 8-pin DIP Package
MOQ: 1 |

TS3702CN Descripción general

The STMicroelectronics TS3702CN is a micropower dual voltage comparator featuring 9 µA typical supply current per comparator, a 1.5 µs response time, and a 6.5 mV maximum input offset voltage. The device is packaged in an 8-pin DIP and uses a CMOS push-pull output stage. Its two independent channels support differential input comparisons with single or dual power-supply operation.

A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the measured relationship crosses a defined threshold. The TS3702 belongs to the comparator hierarchy within analog signal-conditioning integrated circuits. Two integrated channels in one package provide a practical way to monitor two thresholds, control one analog system, or implement complementary sensing functions while reducing board area.

The TS3702's principal advantages are its very low 9 µA typical current consumption per comparator, CMOS input characteristics, and push-pull outputs. Unlike the open-collector outputs used by conventional bipolar comparators such as the LM393 family, push-pull outputs can drive a defined high or low state without an external pull-up resistor. This can simplify output interfacing and reduce board space, although the resulting output current and transition behavior must remain within the device specifications.

According to the STMicroelectronics manufacturer datasheet, the TS3702 can operate from a single positive supply or from split positive and negative supplies. The available comparison information identifies a dual-supply operating span from ±1.35 V to ±8 V, with ±3 V and ±5 V listed as typical dual-supply configurations. Input offset voltage is specified up to 6.5 mV, while propagation delay can reach 1.5 µs. These values position the device for low-power threshold detection rather than high-speed timing applications.

Typical uses include battery-powered sensor conditioning, overvoltage and undervoltage detection, temperature-limit monitoring, window comparators, and low-power control loops. The two channels may also monitor complementary supply or signal thresholds. A push-pull output is particularly useful when the next stage requires a CMOS-compatible logic level and the added quiescent current of an external pull-up network is undesirable.

Designers should verify input common-mode range, output-current limits, supply sequencing, and output behavior for every operating condition using the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, while comparator inputs require short, quiet traces that minimize coupling from switching nodes. The DIP package is suitable for through-hole assembly and prototypes, but modern compact products may require a different package variant and corresponding PCB redesign.

This product page organizes the TS3702CN electrical characteristics, verified drop-in references, pin assignments, comparison parameters, and practical design guidance into one engineering-focused resource. It also distinguishes documented drop-in options from alternatives that require different packages or output structures, helping designers make a PCB-compatible sourcing decision.

Alternativas directas para TS3702CN — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con TS3702CN (mismo factor de forma y huella) — difiere en Comparator Type, Output Type, Package.

STMicroelectronics
Comparator Type: Dual general-purpose voltage comparator
Output Type: Push-pull CMOS
Package: PDIP-8, 8-pin through-hole
Comparar con TS3702CN →

TS3702IN

✅ Sustitución directa
STMicroelectronics
📦 8-pin DIP
Dual general-purpose voltage comparator · 2 channels · 16 V · 9 µA per comparator · 6.5 mV maximum · 1.5 µs maximum · 600 pA maximum

Consulte el precio

Ver hoja de datos →

TLC3702IP

✅ Sustitución directa
📦 8-pin DIP
Same 8-pin PDIP format and dual-comparator use case; the documented pin-count difference is 0, while TI describes upgraded functionality.

📋 Alternativa de referencia (no en el catálogo)

TLC3702CP

✅ Sustitución directa
📦 8-pin DIP
Same 8-pin PDIP format and dual-comparator use case; the documented pin-count difference is 0, with a different TI ordering suffix.

📋 Alternativa de referencia (no en el catálogo)

TS3702CN Valores máximos y características eléctricas

Comparator Type General-purpose voltage comparator
Number of Comparators 2 channels
Supply Current per Comparator 9 µA typical
Input Offset Voltage 6.5 mV maximum
Response Time 1.5 µs maximum
Tipo de salida CMOS push-pull
Logic Family CMOS
Dual-Supply Voltage Range ±1.35 V to ±8 V
Typical Dual-Supply Configurations ±3 V or ±5 V
Maximum Power Dissipation 1250 mW
Encapsulado 8-pin DIP
Recuento de pines 8 pins
Estilo de montaje Through-hole
External Pull-Up Resistor Not required for push-pull output
Comparator Consumption Advantage 20 times lower than bipolar LM393 according to the manufacturer

Configuración de pines de TS3702CN

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
Pin 1 OUT1 — Comparator 1 push-pull output
Pin 2 IN−1 — Comparator 1 inverting input
Pin 3 IN+1 — Comparator 1 non-inverting input
Pin 4 V− — Negative supply or ground connection
Pin 5 IN+2 — Comparator 2 non-inverting input
Pin 6 IN−2 — Comparator 2 inverting input
Pin 7 OUT2 — Comparator 2 push-pull output
Pin 8 V+ — Positive supply connection

Aplicaciones típicas

TS3702CN es adecuado para 6 aplicacións: Battery Threshold Detection, Low-Power Sensor Conditioning, Overvoltage and Undervoltage Window Monitor, Temperature Limit Monitoring, Analog Control-Loop Limit Detector, Signal-Presence and Window Comparator.

⚡

Battery Threshold Detection

The TS3702CN fits low-power battery monitoring because each comparator consumes only 9 µA typically while providing an independent threshold decision. One channel can compare a divided battery voltage against a reference, and the second can monitor another rail or polarity condition. Its push-pull CMOS output can provide a defined logic level without the external pull-up resistor associated with an open-collector LM393-class device. The 1.5 µs maximum response time is sufficient for ordinary battery-limit alarms, while the 6.5 mV maximum input offset must be included in the threshold-error budget.

🧩

Low-Power Sensor Conditioning

The TS3702CN can translate a low-power sensor output into a clean digital threshold event. A resistive divider or sensor network can drive one input while a stable reference drives the other, and the comparator channel then indicates whether the measured quantity is above or below its limit. The 9 µA typical consumption per channel preserves battery headroom, while the 1.5 µs maximum response time is well suited to slow thermal, light, or inertial sensor crossings. Keep the sensor and reference paths short so switching-node noise does not create false transitions at the input offset threshold.

🏭

Overvoltage and Undervoltage Window Monitor

The two independent TS3702CN channels are well suited to upper and lower rail supervision. One comparator can evaluate an overvoltage divided input against a reference, while the other evaluates an undervoltage condition, producing separate push-pull status signals for a controller or system supervisor. This arrangement avoids the external pull-ups required by open-collector outputs and supports CMOS-compatible interfacing. The 6.5 mV maximum offset must be checked against the smallest voltage window, and the reference component should be specified with drift and noise appropriate to the monitored rail.

💊

Temperature Limit Monitoring

A resistive divider connected to a thermistor can drive the TS3702CN input network for an electronic thermal cutoff. The comparator then switches its push-pull output when the temperature crosses the selected threshold, providing a direct alert without continuous microcontroller polling. Its 9 µA typical current per comparator is useful in portable thermal-control systems, and the 1.5 µs maximum response time is more than adequate for most thermal processes. Account for resistor tolerance, thermistor nonlinearity, and the 6.5 mV maximum offset when setting the guaranteed trip point.

🔧

Analog Control-Loop Limit Detector

The TS3702CN can supervise a control loop by comparing a feedback-derived voltage with a command or reference level. If the controlled variable moves outside its valid range, the active push-pull output can immediately drive a digital fault input. This is useful in power, actuator, and industrial-control systems where the comparator performs continuous boundary detection while a microcontroller manages slower recovery actions. The 1.5 µs maximum response time supports rapid protection, while the 6.5 mV maximum input offset and common-mode limitations must be reconciled with the loop’s acceptable error band.

📡

Signal-Presence and Window Comparator

Two TS3702CN channels can implement a signal-presence or window-detection function by placing lower and upper thresholds around a conditioned signal. The comparator outputs indicate whether the signal is below the low limit, inside the accepted window, or above the high limit. This arrangement benefits from the 9 µA typical current per channel and from push-pull outputs that do not require pull-up resistors. The 6.5 mV maximum offset sets a practical threshold-resolution limit, and the 1.5 µs maximum response time is suitable for envelope monitoring rather than high-speed pulse discrimination.

What is the operating voltage of TS3702CN?
The TS3702CN supports a dual-supply range of ±1.35 V to ±8 V and can also operate from a single positive supply. The manufacturer describes ±3 V and ±5 V as typical dual-supply configurations. Confirm the single-supply limits and input common-mode requirements against the STMicroelectronics TS3702 datasheet before applying the comparator at a particular rail voltage.
How much current does each TS3702CN comparator consume?
Each TS3702CN comparator consumes 9 µA typically. STMicroelectronics states that this is approximately 20 times less than the bipolar LM393 family, making the TS3702 suitable for low-power threshold-detection circuits. Actual design current can vary with supply voltage, input state, output state, and operating conditions, so use the datasheet limit tables for worst-case calculations.
What are the key specifications of TS3702CN that engineers should know?
The TS3702CN combines two independent CMOS comparators, 9 µA typical current per channel, 6.5 mV maximum input offset voltage, 1.5 µs maximum response time, and push-pull outputs in one 8-pin DIP package. According to the STMicroelectronics TS3702 manufacturer datasheet, the push-pull configuration eliminates the external pull-up resistor normally required by open-collector comparators.
Where can I download the TS3702CN datasheet PDF?
The official TS3702CN datasheet PDF is available from STMicroelectronics at https://www.st.com/resource/en/datasheet/ts3702.pdf. The manufacturer document is the preferred source for the complete electrical characteristics, input common-mode information, timing limits, power ratings, and package drawings because the TS3702 family is covered rather than only the TS3702CN ordering code.
Where can I find the TS3702CN pinout?
The TS3702CN pinout is defined in the STMicroelectronics TS3702 manufacturer datasheet. The 8-pin DIP uses pins 1 and 7 for the two comparator outputs, pins 2, 3, 5, and 6 for their respective inputs, pin 4 for V− or ground, and pin 8 for V+ or the positive supply. Use the pin-description table when assigning PCB tracks.
What can replace the TS3702CN on the same PCB?
The documented same-footprint candidates are the TS3702IN and the Texas Instruments TLC3702 family in PDIP-8 packages. The TS3702IN retains the STMicroelectronics 8-pin through-hole format, while TLC3702IP and TLC3702CP are identified in comparison data as 8-pin alternatives and TLC3702IP is described by TI as a drop-in replacement with upgraded functionality. Confirm pin functions and timing before substitution.
Is TS3702CN the same as TS3702IN?
The TS3702CN and TS3702IN are both STMicroelectronics 8-pin PDIP comparator options with the same dual-CMOS comparator family structure. Their documented package and pin-count difference is 0, but the ordering suffixes may identify different qualification or packaging characteristics. Confirm the specific suffix requirements in the manufacturer ordering information before treating them as interchangeable.
Is the TS3702CN suitable for battery-powered sensor circuits?
Yes, the TS3702CN is suitable for many battery-powered sensing circuits because each comparator draws 9 µA typically and the push-pull output avoids a continuously loaded external pull-up resistor. It can monitor a sensor signal against a reference, detect a battery threshold, or generate a logic-compatible status signal. The complete input range, output loading, and shutdown requirements must remain within the operating limits.
TS3702CN vs TS3702IN: which is better for a legacy design?
Choose the TS3702CN when the ordering suffix and qualification requirements explicitly call for that exact device; choose the TS3702IN when its manufacturer ordering information satisfies the same requirements. Both are documented as 8-pin PDIP devices with no package or pin-count difference. For a new PCB, also evaluate TLC3702IP or TLC3702CP as cross-brand alternatives with explicitly documented 8-pin drop-in positioning.
When should I choose TS3702CN instead of TLC3702IP?
Choose the TS3702CN when maintaining an STMicroelectronics dual-CMOS comparator design, using its 9 µA typical current per channel, or preserving an established BOM and sourcing arrangement. Choose TLC3702IP when its documented upgraded functionality and same-package comparison make it preferable for a cross-brand redesign. Both are 8-pin through-hole options, but the complete input and timing tables should determine the final choice.
What is the best Texas Instruments equivalent for TS3702CN?
The TLC3702IP is the closest Texas Instruments equivalent identified in the comparison data because it uses the same 8-pin PDIP format and TI describes it as a drop-in replacement with upgraded functionality. The TLC3702CP is another documented 8-pin alternative. Verify output polarity, input common-mode range, supply limits, response time, and latch or shutdown behavior before approving either part.
Can TLC3702IP replace TS3702CN without changing the PCB?
TLC3702IP can be considered a PCB-compatible replacement because the comparison data identifies an 8-pin PDIP package and TI describes it as a drop-in replacement with upgraded functionality. The package and pin-count difference is 0, but a drop-in package alone does not prove identical behavior. Review input thresholds, output polarity, supply range, timing, and any additional functions in both manufacturer datasheets.
Why does the TS3702CN use a push-pull output?
The TS3702CN uses a CMOS push-pull output so the output can actively drive either a high or low state without an external pull-up resistor. This saves board space and reduces the continuous current that can occur when an open-collector output is held low through a pull-up. The design must still respect the comparator's output-current and output-voltage limits when driving the next stage.
Where to buy TS3702CN online?
Use the Request a Quote form on this page to request TS3702CN availability, current lead time, and a quotation for the exact 8-pin DIP ordering code. The manufacturer part number is TS3702CN, and confirming that suffix is important because related TS3702 variants use different package or qualification codes. The form provides a direct purchasing channel without relying on a static distributor listing.
What is the price and lead time of TS3702CN?
Current commercial terms for TS3702CN are available through the Request a Quote form on this page. Submit the required quantity, target packaging, and delivery location so the quotation can reflect current component availability and lead time. The exact ordering code should be stated as TS3702CN to avoid confusion with other TS3702 package variants.
Is TS3702CN currently active and in stock?
The manufacturer product information identifies the TS3702 as an active micropower dual CMOS comparator family. Current exact-SKU inventory is not represented here, so use the Request a Quote form on this page to check TS3702CN stock, minimum order quantity, and lead time. Request the 8-pin DIP configuration explicitly when submitting the request.

Datos de referencia de ingeniería para TS3702CN — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the TS3702CN for a new or maintained design that requires two micropower CMOS comparators, 9 µA typical consumption per channel, and a push-pull output in an 8-pin DIP package. It is especially useful for battery threshold detection, rail supervision, sensor limiting, and window comparisons where an external pull-up resistor is undesirable. Choose TS3702IN when the ordering and qualification requirements of that STMicroelectronics suffix better match the design while retaining the same 8-pin DIP format. Evaluate TLC3702IP or TLC3702CP when a Texas Instruments sourcing option or the additional functionality described for the TI family is preferable, but verify common-mode range, timing, offset, polarity, and operating limits before replacement. The TS3702CN should not be selected for applications requiring high-speed decision accuracy or a rail-to-rail input range unless the complete manufacturer specifications confirm those requirements.

Comparación con alternativas

Parámetro Este producto TS3702IN TLC3702IP TLC3702CP
Brand STMicroelectronics STMicroelectronics Texas Instruments Texas Instruments
Package 8-pin DIP 8-pin DIP 8-pin PDIP 8-pin PDIP

Diferenciadores clave

  • Low quiescent current for a dual comparator (frente a LM393-family bipolar comparator)
  • No external output pull-up is required (frente a LM2902N/PB)
  • Documented PCB-compatible cross-brand route (frente a TLC3702IP)
  • Two independent channels in one through-hole package (frente a LM2904PWR)

Notas de diseño

Do not treat the identical 8-pin DIP footprint as proof of identical behavior. Before substituting TS3702IN, TLC3702IP, or TLC3702CP, compare input common-mode range, output polarity, supply limits, propagation delay, offset voltage, and any latch or shutdown features in the manufacturer datasheets. The TS3702CN has a documented 6.5 mV maximum input offset and 1.5 µs maximum response time, so tighter systems may require these parameters to remain unchanged.

Route the two comparator inputs directly to their sensing or reference networks and keep them away from switching nodes. Place supply-decoupling capacitors close to pins 8 and 4, with the shortest possible return path to ground. Because the outputs are push-pull, route them as ordinary low-speed digital signals, but check output loading and timing rather than assuming an open-collector interface can be reproduced without the external pull-up resistor.

Estimated: the TS3702CN's typical current is 9 µA per comparator, giving 18 µA for two channels under the stated typical condition. Actual design current must be calculated from the maximum supply current for both channels over the full input and output voltage states, plus reference and feedback-network current. This typical-only estimate is not a substitute for the worst-case limits in the STMicroelectronics datasheet.

For slow threshold detection, deliberately slow the comparator output or add hysteresis rather than relying on extremely low-noise input routing alone. Hysteresis prevents small ripple around the threshold from repeatedly toggling the push-pull output. Select the feedback resistor and input network so the hysteresis is larger than the 6.5 mV maximum offset while remaining within the input bias-current and common-mode constraints.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The manufacturer product page and datasheet excerpts used for this product page do not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status.

Datos verificados el: 2026-11-16 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

TS3702CN datasheet TS3702CN pinout TS3702CN datasheet pdf TS3702CN equivalent TS3702CN replacement TS3702CN cross reference TS3702CN vs TLC3702IP TS3702CN footprint TS3702CN price TS3702CN stock STMicroelectronics TS3702CN TS3702CN application circuit

Componentes & términos relacionados

STMicroelectronics TS3702CN TS3702IN TLC3702IP TLC3702CP LM2902N/PB LM2904PWR voltage comparator dual comparator analog comparator analog integrated circuit CMOS push-pull output open-collector output 8-pin DIP PDIP-8 through-hole package input offset voltage supply current response time battery threshold detection sensor conditioning overvoltage monitoring
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ