TS3702CN - 9µA Dual CMOS Comparator | STMicroelectronics
MPN: TS3702CN ✓ Hoạt độngTS3702CN Tóm tắt
A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the measured relationship crosses a defined threshold. The TS3702 belongs to the comparator hierarchy within analog signal-conditioning integrated circuits. Two integrated channels in one package provide a practical way to monitor two thresholds, control one analog system, or implement complementary sensing functions while reducing board area.
The TS3702's principal advantages are its very low 9 µA typical current consumption per comparator, CMOS input characteristics, and push-pull outputs. Unlike the open-collector outputs used by conventional bipolar comparators such as the LM393 family, push-pull outputs can drive a defined high or low state without an external pull-up resistor. This can simplify output interfacing and reduce board space, although the resulting output current and transition behavior must remain within the device specifications.
According to the STMicroelectronics manufacturer datasheet, the TS3702 can operate from a single positive supply or from split positive and negative supplies. The available comparison information identifies a dual-supply operating span from ±1.35 V to ±8 V, with ±3 V and ±5 V listed as typical dual-supply configurations. Input offset voltage is specified up to 6.5 mV, while propagation delay can reach 1.5 µs. These values position the device for low-power threshold detection rather than high-speed timing applications.
Typical uses include battery-powered sensor conditioning, overvoltage and undervoltage detection, temperature-limit monitoring, window comparators, and low-power control loops. The two channels may also monitor complementary supply or signal thresholds. A push-pull output is particularly useful when the next stage requires a CMOS-compatible logic level and the added quiescent current of an external pull-up network is undesirable.
Designers should verify input common-mode range, output-current limits, supply sequencing, and output behavior for every operating condition using the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, while comparator inputs require short, quiet traces that minimize coupling from switching nodes. The DIP package is suitable for through-hole assembly and prototypes, but modern compact products may require a different package variant and corresponding PCB redesign.
This product page organizes the TS3702CN electrical characteristics, verified drop-in references, pin assignments, comparison parameters, and practical design guidance into one engineering-focused resource. It also distinguishes documented drop-in options from alternatives that require different packages or output structures, helping designers make a PCB-compatible sourcing decision.
Bộ thay thế dễ dàng lắp đặt cho TS3702CN — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với TS3702CN (cùng hình factor và footprint) — khác nhau ở Comparator Type, Output Type, Package.
TS3702IN
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →TLC3702IP
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TLC3702CP
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TS3702CN Tỷ lệ tối đa & tính chất điện
| Comparator Type | General-purpose voltage comparator |
| Number of Comparators | 2 channels |
| Supply Current per Comparator | 9 µA typical |
| Input Offset Voltage | 6.5 mV maximum |
| Response Time | 1.5 µs maximum |
| Kiểu đầu ra | CMOS push-pull |
| Logic Family | CMOS |
| Dual-Supply Voltage Range | ±1.35 V to ±8 V |
| Typical Dual-Supply Configurations | ±3 V or ±5 V |
| Maximum Power Dissipation | 1250 mW |
| Hộp | 8-pin DIP |
| Số chân | 8 pins |
| Kiểu lắp đặt | Through-hole |
| External Pull-Up Resistor | Not required for push-pull output |
| Comparator Consumption Advantage | 20 times lower than bipolar LM393 according to the manufacturer |
Cấu hình chân TS3702CN
| Chân 1 | OUT1 — Comparator 1 push-pull output |
| Chân 2 | IN−1 — Comparator 1 inverting input |
| Chân 3 | IN+1 — Comparator 1 non-inverting input |
| Chân 4 | V− — Negative supply or ground connection |
| Chân 5 | IN+2 — Comparator 2 non-inverting input |
| Chân 6 | IN−2 — Comparator 2 inverting input |
| Chân 7 | OUT2 — Comparator 2 push-pull output |
| Chân 8 | V+ — Positive supply connection |
Ứng dụng tiêu biểu
TS3702CN phù hợp cho 6 Áp dụngs: Battery Threshold Detection, Low-Power Sensor Conditioning, Overvoltage and Undervoltage Window Monitor, Temperature Limit Monitoring, Analog Control-Loop Limit Detector, Signal-Presence and Window Comparator.
Battery Threshold Detection
The TS3702CN fits low-power battery monitoring because each comparator consumes only 9 µA typically while providing an independent threshold decision. One channel can compare a divided battery voltage against a reference, and the second can monitor another rail or polarity condition. Its push-pull CMOS output can provide a defined logic level without the external pull-up resistor associated with an open-collector LM393-class device. The 1.5 µs maximum response time is sufficient for ordinary battery-limit alarms, while the 6.5 mV maximum input offset must be included in the threshold-error budget.
Được đề xuất
Low-Power Sensor Conditioning
The TS3702CN can translate a low-power sensor output into a clean digital threshold event. A resistive divider or sensor network can drive one input while a stable reference drives the other, and the comparator channel then indicates whether the measured quantity is above or below its limit. The 9 µA typical consumption per channel preserves battery headroom, while the 1.5 µs maximum response time is well suited to slow thermal, light, or inertial sensor crossings. Keep the sensor and reference paths short so switching-node noise does not create false transitions at the input offset threshold.
Được đề xuất
Overvoltage and Undervoltage Window Monitor
The two independent TS3702CN channels are well suited to upper and lower rail supervision. One comparator can evaluate an overvoltage divided input against a reference, while the other evaluates an undervoltage condition, producing separate push-pull status signals for a controller or system supervisor. This arrangement avoids the external pull-ups required by open-collector outputs and supports CMOS-compatible interfacing. The 6.5 mV maximum offset must be checked against the smallest voltage window, and the reference component should be specified with drift and noise appropriate to the monitored rail.
Được đề xuất
Temperature Limit Monitoring
A resistive divider connected to a thermistor can drive the TS3702CN input network for an electronic thermal cutoff. The comparator then switches its push-pull output when the temperature crosses the selected threshold, providing a direct alert without continuous microcontroller polling. Its 9 µA typical current per comparator is useful in portable thermal-control systems, and the 1.5 µs maximum response time is more than adequate for most thermal processes. Account for resistor tolerance, thermistor nonlinearity, and the 6.5 mV maximum offset when setting the guaranteed trip point.
Được đề xuất
Analog Control-Loop Limit Detector
The TS3702CN can supervise a control loop by comparing a feedback-derived voltage with a command or reference level. If the controlled variable moves outside its valid range, the active push-pull output can immediately drive a digital fault input. This is useful in power, actuator, and industrial-control systems where the comparator performs continuous boundary detection while a microcontroller manages slower recovery actions. The 1.5 µs maximum response time supports rapid protection, while the 6.5 mV maximum input offset and common-mode limitations must be reconciled with the loop’s acceptable error band.
Được đề xuất
Signal-Presence and Window Comparator
Two TS3702CN channels can implement a signal-presence or window-detection function by placing lower and upper thresholds around a conditioned signal. The comparator outputs indicate whether the signal is below the low limit, inside the accepted window, or above the high limit. This arrangement benefits from the 9 µA typical current per channel and from push-pull outputs that do not require pull-up resistors. The 6.5 mV maximum offset sets a practical threshold-resolution limit, and the 1.5 µs maximum response time is suitable for envelope monitoring rather than high-speed pulse discrimination.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho TS3702CN — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | TS3702IN | TLC3702IP | TLC3702CP |
|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | Texas Instruments | Texas Instruments |
| Package | 8-pin DIP | 8-pin DIP | 8-pin PDIP | 8-pin PDIP |
Bảo phân biệt quan trọng
- Low quiescent current for a dual comparator (vsLM393-family bipolar comparator)
- No external output pull-up is required (vsLM2902N/PB)
- Documented PCB-compatible cross-brand route (vsTLC3702IP)
- Two independent channels in one through-hole package (vsLM2904PWR)
Ghi chú thiết kế
Do not treat the identical 8-pin DIP footprint as proof of identical behavior. Before substituting TS3702IN, TLC3702IP, or TLC3702CP, compare input common-mode range, output polarity, supply limits, propagation delay, offset voltage, and any latch or shutdown features in the manufacturer datasheets. The TS3702CN has a documented 6.5 mV maximum input offset and 1.5 µs maximum response time, so tighter systems may require these parameters to remain unchanged.
Route the two comparator inputs directly to their sensing or reference networks and keep them away from switching nodes. Place supply-decoupling capacitors close to pins 8 and 4, with the shortest possible return path to ground. Because the outputs are push-pull, route them as ordinary low-speed digital signals, but check output loading and timing rather than assuming an open-collector interface can be reproduced without the external pull-up resistor.
Estimated: the TS3702CN's typical current is 9 µA per comparator, giving 18 µA for two channels under the stated typical condition. Actual design current must be calculated from the maximum supply current for both channels over the full input and output voltage states, plus reference and feedback-network current. This typical-only estimate is not a substitute for the worst-case limits in the STMicroelectronics datasheet.
For slow threshold detection, deliberately slow the comparator output or add hysteresis rather than relying on extremely low-noise input routing alone. Hysteresis prevents small ripple around the threshold from repeatedly toggling the push-pull output. Select the feedback resistor and input network so the hysteresis is larger than the 6.5 mV maximum offset while remaining within the input bias-current and common-mode constraints.
Thông tin tuân thủ
The manufacturer product page and datasheet excerpts used for this product page do not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status.