TS914ID - Quad Rail-to-Rail CMOS Op Amp | STMicroelectronics
N.º de pieza: TS914ID ✓ ActivoTS914ID Descripción general
A CMOS operational amplifier is a voltage-controlled, high-gain analog building block whose differential input is amplified relative to ground or another reference voltage. The TS914 belongs to the operational-amplifier hierarchy, combining four amplifiers in one integrated circuit. It is designed for low-power, single-supply and dual-supply systems where four independent analog channels can be implemented in one compact 14-pin SOIC package.
Key features include four amplifier channels, rail-to-rail input and output ranges, a 2.7 V to 16 V supply-voltage range, and a 1.4 MHz gain-bandwidth product. The typical input bias current of 1 pA is particularly valuable when source impedances are high, because it minimizes the voltage error caused by bias current. The reported 200 µA supply current per amplifier at 3 V also supports battery-powered and portable equipment when the required bandwidth is moderate.
The TS914's CMOS input stage enables operation close to the supply rails and supports low input bias current. Its 1.4 MHz bandwidth is appropriate for general-purpose amplification, filtering, buffering, and signal conditioning rather than high-speed precision instrumentation. Because the maximum offset voltage is specified as 2 mV, applications demanding sub-millivolt accuracy require additional calibration or a more precise amplifier.
Typical uses include four-channel sensor interfaces, low-frequency active filters, audio and communication signal conditioning, portable instrumentation, and industrial control modules. Placing all four channels in one SOIC package reduces board area and external component count. Input common-mode and output swing limits, output-current capability, noise, and stability should still be checked against the manufacturer datasheet before fixing the supply voltage and external network.
For reliable single-supply operation, keep the input common-mode voltage within the supported range, place input and feedback components close to the device, and provide suitable bypassing at each supply pin. Decoupling requirements and compensation values must follow the manufacturer datasheet rather than generic assumptions. If the source resistance is high, account for input bias-current and capacitance errors, and confirm that the selected feedback topology remains stable at the intended gain.
This product page consolidates verified manufacturer and distributor information with package, application, replacement, and design guidance. It distinguishes verified parameters from information that still requires datasheet review, helping engineers evaluate TS914ID without mistaking generic amplifier assumptions for guaranteed TS914ID characteristics.
Alternativas directas para TS914ID — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con TS914ID (mismo factor de forma y huella) — difiere en Amplifier Type, Package, Gain-Bandwidth Product, Supply Voltage Range, Input Offset Voltage.
TS914AIYD
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
TS914AIYDT
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
TS27M4IDT
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
TS912ID
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →TS902ID
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →LMC6494BEMX/NOPB
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
TS914ID Valores máximos y características eléctricas
| Amplifier Type | Quad CMOS operational amplifier |
| Number of Channels | 4 channels |
| Input and Output Type | Rail-to-rail input and output |
| Supply Voltage Range | 2.7 V to 16 V |
| Supply Configuration | Single or dual supply |
| Gain-Bandwidth Product | 1.4 MHz |
| Input Bias Current | 1 pA typical |
| Input Offset Voltage | 2 mV maximum |
| Supply Current per Amplifier | 200 µA at 3 V |
| Encapsulado | 14-pin SOIC |
| Tipo de montaje | Surface mount |
| Process Technology | CMOS |
Guía de configuración de pines de TS914ID 14-pin soic
Configuración de pines para TS914ID (encapsulado 14-pin soic). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para TS914ID.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
TS914ID es adecuado para 6 aplicacións: High-Impedance Sensor Signal Conditioning, Portable Battery-Powered Instrumentation, Industrial Four-Channel Signal Conditioning, Low-Frequency Active Filtering, Audio and Communication Buffers, Battery Management and Voltage Monitoring.
High-Impedance Sensor Signal Conditioning
The TS914ID fits high-impedance sensor interfaces because its rail-to-rail input range accommodates signals near either supply rail and its 1 pA typical input bias current limits the error introduced by source resistance. Four amplifiers can condition four sensor channels within one 14-pin SOIC package. The 1.4 MHz gain-bandwidth product is sufficient for many temperature, light, humidity, and capacitive-sensing channels, while the 2 mV maximum offset voltage requires attention in high-accuracy measurements. Calibration may be necessary when the sensor and amplifier offsets contribute materially to the system error budget.
Recomendado
Portable Battery-Powered Instrumentation
The TS914ID is appropriate for portable instrumentation because it operates from 2.7 V to 16 V and consumes a verified 200 µA per amplifier at 3 V. Its rail-to-rail input and output capability preserves signal headroom in low-voltage systems, while four channels reduce the number of packages required for a multichannel instrument. The 1.4 MHz bandwidth supports moderate-speed sensing and control rather than waveform capture at high frequencies. Battery-life calculations must include the aggregate current of four active amplifiers, output loading, leakage, and any external analog circuitry.
Recomendado
Industrial Four-Channel Signal Conditioning
The TS914ID can condition four low-frequency industrial sensor channels within a 2.7 V to 16 V control system. Its rail-to-rail input and output ranges simplify scaling around low-voltage analog nodes, and the 14-pin SOIC package reduces board area compared with four single-amplifier packages. The 1.4 MHz gain-bandwidth product supports general-purpose gain and active-filter stages, but channel bandwidth, input common-mode behavior, and output settling must be checked against the factory datasheet. Industrial surge, temperature, and EMC requirements should be evaluated separately from the basic amplifier specifications.
Recomendado
Low-Frequency Active Filtering
The TS914ID is suitable for low-frequency active filters when four channels can share one package. Its 1.4 MHz gain-bandwidth product leaves bandwidth for moderate closed-loop gains, and its CMOS input stage provides a verified 1 pA typical bias current that helps preserve high-impedance filter behavior. Component tolerances and the amplifier's gain-bandwidth response can determine the realized cutoff and stopband behavior. The exact resistor and capacitor values, permissible noise gain, and stability conditions must be selected from the manufacturer datasheet and verified on the assembled board.
Recomendado
Audio and Communication Buffers
The TS914ID can provide low-level buffering and gain for audio or communication interfaces that operate within its 1.4 MHz bandwidth and 2.7 V to 16 V supply range. Rail-to-rail I/O operation is useful with low-voltage codecs, sensors, and line-level interface circuits. However, the TS914ID is a general-purpose CMOS amplifier, so noise density, harmonic distortion, channel separation, and output-drive data must be checked before using it in high-fidelity audio. Four channels allow matched buffering for stereo or multi-interface designs when board layout and thermal conditions are controlled.
Recomendado
Battery Management and Voltage Monitoring
The TS914ID can support current sensing, battery-voltage monitoring, threshold comparison, and low-frequency feedback loops in a compact power-management module. Rail-to-rail input operation is helpful when monitoring signals extend toward a low-voltage supply rail, and the 1 pA typical bias current is advantageous with high-resistance sense elements. The 2 mV maximum offset must be included in the measurement error budget. The amplifier is not itself a charger or protection controller, so its use should remain limited to the analog monitoring and control functions validated by the system design.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para TS914ID — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | TS914AIYD | TS914AIYDT | TS27M4IDT | TS912ID | TS902ID | LMC6494BEMX/NOPB |
|---|---|---|---|---|---|---|---|
| Package | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | Texas Instruments |
| Amplifier Configuration | Quad | Quad | Quad | Quad | Quad | Quad | Quad |
Diferenciadores clave
- Four rail-to-rail channels in one 14-pin SOIC package (frente a LMC6494BEMX/NOPB)
- Low 1 pA typical input bias current (frente a TS27M4IDT)
- Broad verified 2.7 V to 16 V supply range (frente a TS912ID)
- Automotive-grade same-family ordering options (frente a TS914ID)
Notas de diseño
Place the manufacturer-recommended bypass capacitors immediately adjacent to the TS914ID supply pins and connect them to a low-impedance ground plane. Keep input and feedback-component connections short to minimize parasitic coupling. Because the device provides four channels in one 14-pin SOIC package, route each channel independently and avoid sharing long high-impedance input traces. The supplied web results do not state the required capacitor values, so those values must be taken from the STMicroelectronics TS914 datasheet rather than inferred from generic op-amp practice.
Do not treat the 2 mV maximum input offset voltage as adequate for every precision measurement. Include the offset error, input bias-current error, noise, and resistor tolerance in the system error budget. For a high-value source resistance, the verified 1 pA typical input bias current can still produce a meaningful voltage error even though it is low. Verify the actual minimum and maximum input resistance, source leakage, and operating temperature before selecting the amplifier for high-impedance precision sensing.
The 1.4 MHz gain-bandwidth product limits the useful closed-loop bandwidth as gain rises. For example, a gain of 10 implies an approximate 140 kHz bandwidth under a simplified gain-bandwidth estimate; this is an estimate and must be confirmed against the manufacturer curve. Avoid operating close to the gain-bandwidth limit if phase margin, settling time, or noise-gain peaks are important. Use the datasheet's recommended feedback network and evaluate the finalized layout because an unsuitable feedback ratio can compromise stability.
The verified supply-current value is 200 µA per amplifier at 3 V, so four continuously active channels can consume roughly 800 µA before external loads and bias effects are included. That is an estimate derived from the quoted per-amplifier value, not a separate maximum supply-current specification. Battery-powered designs should sum the current of all four channels and account for sleep-mode availability, output loading, leakage, voltage dependence, and the behavior of the chosen operating state before estimating battery life.
Información de cumplimiento
The supplied verified data does not provide explicit compliance statements. The TS914AIYD and TS914AIYDT ordering codes are presented as automotive family alternatives, but an AEC-Q100 qualification statement was not included and has not been inferred. The RoHS state on one third-party listing was a verification request rather than a confirmed declaration.