TS971ILT - 12 MHz Low-Noise R-R Operational Amplifier | STMicroelectronics
N.º de pieza: TS971ILT ✓ ActivoTS971ILT Descripción general
An operational amplifier is an analog active component that uses high-gain feedback to amplify voltage differences. The TS971 belongs to the operational-amplifier hierarchy, which includes general-purpose amplifiers, rail-to-rail input/output amplifiers, low-noise amplifiers, and precision signal-chain devices. Its rail-to-rail output allows the output voltage to approach the supply rails, improving utilization of available supply voltage in portable equipment.
The TS971ILT combines low-noise operation with a 12 MHz gain-bandwidth product and 4 V/us slew rate. These characteristics make it useful for audio preamplification, sensor conditioning, active filtering, and low-level signal amplification where bandwidth and noise must be balanced. The single-amplifier configuration also reduces board area compared with dual or quad devices.
The device supports supply voltages as low as 2.7 V and is characterized for operation up to 10 V. Its SOT-23-5 package is suitable for surface-mount construction, although the exposed thermal limitations of the small package require attention when driving capacitive loads or operating continuously at high output swing. The input common-mode behavior and output swing should be checked against the system supply rails in the manufacturer datasheet.
Typical uses include portable audio signal paths, microphone and sensor interfaces, low-frequency filters, and general instrumentation. For battery-powered systems, the low-voltage operation can simplify power architecture and reduce the need for a higher-voltage analog rail. In signal-chain designs, the low-noise characteristics help preserve weak signals before conversion or measurement.
Place input and output decoupling capacitors close to the device pins, keep analog traces short, and provide adequate return-current paths. Verify stability with the source and load impedances used in the final circuit, especially when driving long capacitive loads. This page combines manufacturer-family details, package information, pricing structure, replacement guidance, and practical design notes for faster component selection.
Alternativas directas para TS971ILT — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
TS971IYDT
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
TS972ILT
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
TS973ILT
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
TS974ILT
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
TS975ILT
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
TS971ILT Valores máximos y características eléctricas
| Product Type | Single operational amplifier |
| Amplifier Count | 1 amplifier |
| Gain-Bandwidth Product | 12 MHz |
| Slew Rate | 4 V/us |
| Supply Voltage Range | 2.7 V to 10 V |
| Output Swing | Rail-to-rail |
| Noise Characteristics | Very low noise |
| Application Category | General-purpose operational amplifier |
| Encapsulado | SOT-23-5, 5 pins |
| Tipo de montaje | Surface mount |
| Manufacturer Product Family | TS97x low-noise operational-amplifier family |
Configuración de pines de TS971ILT
| Pin 1 | NC — Not connected |
| Pin 2 | IN- — Inverting input |
| Pin 3 | IN+ — Non-inverting input |
| Pin 4 | V- — Negative supply or ground |
| Pin 5 | OUT — Operational-amplifier output |
Aplicaciones típicas
TS971ILT es adecuado para 6 aplicacións: Portable Audio Preamplification, Battery-Powered Sensor Conditioning, Active Low-Frequency Filters, Low-Level Analog Signal Amplification, Portable Instrumentation, Battery-Powered Analog Interface.
Portable Audio Preamplification
The TS971ILT fits portable audio preamplification because the manufacturer describes the TS97x family as very low-noise with low distortion characteristics. Its 12 MHz gain-bandwidth product and 4 V/us slew rate provide more than enough bandwidth for ordinary audio-band signals, while the 2.7 V to 10 V supply range supports 3 V and 5 V portable systems. Place the amplifier close to the source to minimize induced noise, and use stable feedback components so gain does not vary with temperature or tolerance. The rail-to-rail output helps preserve signal swing when the audio signal operates near the available supply range.
Recomendado
Battery-Powered Sensor Conditioning
The TS971ILT is appropriate for conditioning weak signals from battery-powered sensors because its very low-noise architecture preserves small analog signals while the low-voltage operation fits portable supply rails. The 12 MHz gain-bandwidth product allows useful loop bandwidth in active filters and instrumentation amplifiers without requiring a larger package. The 2.7 V minimum operating voltage also helps reduce the number of conversion stages in a compact sensor node. Designers should verify input common-mode limits and output swing against the sensor's signal range, and confirm stability when the sensor presents capacitive loading.
Recomendado
Active Low-Frequency Filters
The TS971ILT can implement active low-frequency filters in compact portable and industrial signal-processing boards. Its 12 MHz gain-bandwidth product supports gain and phase requirements well above the filter corner frequency, and the 4 V/us slew rate helps preserve low-distortion operation for moderate signal amplitudes. The SOT-23-5 footprint reduces board area compared with larger SOIC packages. Select resistor and capacitor values with appropriate tolerances, keep feedback loops compact, and check the amplifier's stability requirements with the intended source and load. The 2.7 V to 10 V range allows the same filter topology to operate across several system rails.
Recomendado
Low-Level Analog Signal Amplification
The TS971ILT is suited to low-level analog signal amplification where a small voltage difference must be enlarged before measurement or conversion. Its very low-noise designation helps reduce contributions that could obscure weak sensor outputs, and the rail-to-rail output can improve usable signal range in a constrained supply design. The single amplifier in a 5-pin SOT-23-5 package simplifies point-of-measurement placement and reduces PCB area. For best results, use short low-impedance source paths, maintain a clean ground reference, and confirm input bias-current and offset-voltage requirements in the manufacturer datasheet before selecting resistor values.
Recomendado
Portable Instrumentation
The TS971ILT can support portable instrumentation front ends because it combines a compact SOT-23-5 package, a 2.7 V to 10 V operating range, and a useful 12 MHz gain-bandwidth product. The family is positioned for very low-noise operation, making the device relevant to battery-powered meters, compact test equipment, and low-level measurement interfaces. Rail-to-rail output allows the circuit to use more of the available supply voltage than a fixed-headroom amplifier. The main engineering trade-off is package thermal and capacitive-load capability, so use short output traces, verify the load configuration, and provide stable feedback compensation where required.
Recomendado
Battery-Powered Analog Interface
The TS971ILT is well matched to battery-powered analog interfaces that need amplification before a converter or microcontroller samples the signal. The 2.7 V minimum supply allows operation from low-energy rails, while the very low-noise characteristic helps preserve signals close to the quantization floor of the downstream converter. The 4 V/us slew rate supports faster transient content than the minimum audio band, and rail-to-rail output improves utilization of the available voltage range. Confirm the converter's input range, sample rate, and antialiasing requirements, then place the amplifier and feedback network close to the source to minimize board-level noise pickup.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para TS971ILT — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | TS971IYDT | TS972ILT | TS973ILT | TS974ILT | TS975ILT |
|---|---|---|---|---|---|---|
| Package | SOT-23-5 | SOT-23-5 | SOT-23-5 | SOT-23-5 | SOT-23-5 | SOT-23-5 |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Product Type | Single operational amplifier | Single operational amplifier | Single operational amplifier | Single operational amplifier | Single operational amplifier | Single operational amplifier |
| Supply Voltage Range | 2.7 V to 10 V | 2.7 V to 10 V | 2.7 V to 10 V | 2.7 V to 10 V | 2.7 V to 10 V | 2.7 V to 10 V |
| Primary Application | Portable and battery-supplied equipment | Portable and battery-supplied equipment | TS97x general-purpose amplification | TS97x general-purpose amplification | TS97x general-purpose amplification | TS97x general-purpose amplification |
Diferenciadores clave
- Low-voltage rail-to-rail operation (frente a TS971IYDT)
- Compact signal-path footprint (frente a TS972ILT)
- Portable-system voltage compatibility (frente a TS973ILT)
Notas de diseño
The TS971ILT operates from 2.7 V to 10 V, so check the complete signal range against the supply rails before designing the feedback network. Keep the input bypass capacitor physically close to the supply pin and use a short, low-impedance ground return. Because rail-to-rail output can approach the supply limits, leave additional margin for load-dependent swing, distortion, and output-current limits.
Place the amplifier, feedback resistors, and compensation components as close together as practical. Route the inverting input directly to the feedback node to minimize parasitic capacitance, and avoid routing high-current or digital-clock traces beneath the analog input. The small SOT-23-5 package benefits from careful ground-plane continuity because long return paths can increase noise pickup and reduce signal margin.
Do not assume that every TS97x suffix is electrically interchangeable. Confirm the exact gain configuration, supply range, input common-mode limits, offset voltage, bias current, and temperature grade in the manufacturer datasheet. If the output drives a capacitive load, begin with a small test load and verify stability with an oscilloscope; the small SOT-23-5 package also limits continuous dissipation.
Información de cumplimiento
The available product listings identify the TS971 family and package but do not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements.