XC7A50T-L1CSG325I 52,160-Cell Artix-7 FPGA | AMD
N.º de pieza: XC7A50T-L1CSG325I ✓ ActivoXC7A50T-L1CSG325I Descripción general
An FPGA is a semiconductor device whose digital logic, interconnect, and configurable I/O are programmed after manufacture. Artix-7 FPGAs occupy the low-cost, low-power portion of the AMD 7 Series portfolio, combining programmable logic with integrated memory resources and analog mixed-signal peripherals. Compared with a fixed-function application-specific integrated circuit, an FPGA allows interface standards, control sequences, and parallel data paths to be revised through a new configuration bitstream without changing the PCB.
The XC7A50T-L1CSG325I provides 52,160 logic cells and 150 I/O in a compact 324-ball package. Its 28 nm process supports efficient implementation of control logic, communication bridges, data acquisition, and embedded signal-processing functions. The associated XC7A50T-1CSG325I information identifies a 0.95 V to 1.05 V core-supply range and a maximum clock frequency of 1098 MHz. These figures establish useful design targets for timing closure, power planning, and external memory-interface implementation.
The CSG325 package supports a high-density ball-grid interface intended for multilayer PCB construction. Pin assignment must follow the AMD Artix-7 package pinout files and UG475 conventions rather than a generic BGA drawing. Differential clock inputs, configuration pins, power rails, and user I/O require careful bank-specific planning because voltage standards, current capacity, and simultaneous-switching-noise limits depend on the selected bank and supply configuration.
Typical implementations include industrial automation, camera and image-processing interfaces, test equipment, low-cost communications infrastructure, embedded control, and general-purpose prototyping. The device is particularly useful when several interfaces require concurrent operation and the firmware or configuration may evolve. A 150-I/O resource count supports parallel buses and control peripherals while conserving board area compared with a larger package.
Power and layout planning should begin with the manufacturer configuration, bank assignment, and decoupling guidance. Keep each power rail close to its assigned supply pins, use the prescribed decoupling network, provide clean clocking, and control return paths for high-speed interfaces. Configuration storage, programming access, and voltage sequencing must also be designed according to the Artix-7 configuration guidelines before power is applied.
This page combines the Artix-7 device identity, package details, application guidance, migration options, and PCB-design considerations to support component selection and engineering review. It also distinguishes speed-grade and temperature-grade alternatives that retain the CSG325 footprint, helping teams identify a compatible replacement while recognizing that every migration still requires timing, power, and configuration verification.
Alternativas directas para XC7A50T-L1CSG325I — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con XC7A50T-L1CSG325I (mismo factor de forma y huella) — difiere en Logic Cells, Package, Speed Grade, Temperature Grade.
XC7A50T-1CSG325I
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
XC7A50T-2CSG325I
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →XC7A50T-1CSG325C
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
XC7A50T-2CSG325C
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
XC7A50T-3CSG325I
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
XC7A50T-L1CSG325I Valores máximos y características eléctricas
| Device Type | Artix-7 field-programmable gate array |
| Logic Cells | 52,160 cells |
| User I/O | 150 I/O |
| Process Technology | 28 nm |
| Core Supply Voltage | 0.95 V to 1.05 V |
| Frecuencia de reloj máxima | 1098 MHz |
| Encapsulado | 324-ball CSPBGA, 324-LFBGA |
| Device Family | Artix-7 |
| FPGA Type | FPGA |
| Architecture | 7 Series FPGA |
| Speed Grade | -1 |
| Temperature Grade | Industrial |
| Tipo de montaje | Surface mount |
| Packaging Form | Tray |
| Programmable Logic | FPGA configuration bitstream |
Guía de configuración de pines de XC7A50T-L1CSG325I 324-ball cspbga, 324-lfbga
Configuración de pines para XC7A50T-L1CSG325I (encapsulado 324-ball cspbga, 324-lfbga). Este CI digital incluye GPIO, interfaces de comunicación (UART, SPI, I2C) y pines de alimentación. Consulte la hoja de datos del fabricante para conocer las funciones alternativas de los pines y las opciones de configuración. Esencial para el diseño de sistemas embebidos y el diseño de PCB.
No hay datos detallados de patillaje disponibles para XC7A50T-L1CSG325I.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
XC7A50T-L1CSG325I es adecuado para 6 aplicacións: Industrial Automation Controller, Machine Vision Interface, Test and Measurement Equipment, Embedded Communications Bridge, Data Acquisition System, Programmable Logic Prototype.
Industrial Automation Controller
The XC7A50T-L1CSG325I is appropriate for an industrial controller that combines machine sequencing, sensor conditioning interfaces, and communications logic. Its 52,160 logic cells provide capacity for control state machines and parallel data handling, while 150 user I/O support multiple digital interfaces without requiring the largest Artix-7 package. The industrial suffix supports deployment in temperature-demanding equipment, subject to the exact limits in the AMD data sheet. Place the FPGA beside the sensor interface circuitry, use separate clock and power planes, and validate timing for motor-control, encoder, and safety-adjacent signals before production release.
Recomendado
Machine Vision Interface
The XC7A50T-L1CSG325I can serve as the programmable interface between image sensors and downstream processing. Its 150 I/O provide parallel sensor-control, synchronization, and data-capture paths, while 52,160 logic cells can implement timing generation, packet assembly, buffer management, and test-pattern logic. The -1 device is suitable when timing analysis confirms that the selected clocking and I/O standards meet the required frame rate. Use the AMD CSG325 pinout to place clock-capable inputs near clock-generation circuitry, route source-synchronous interfaces with controlled impedance, and validate timing margins against the worst-case sensor and cable conditions.
Recomendado
Test and Measurement Equipment
The XC7A50T-L1CSG325I is useful in programmable test equipment where pattern generation, acquisition control, and timing must be changed without redesigning the PCB. The 52,160-cell fabric can support multiple concurrent state machines, while 150 I/O allow dense connections to instruments and fixtures. Its -1 speed grade and industrial suffix are relevant to equipment operating outside benign room-temperature conditions. Engineers should partition clock regions carefully, use dedicated configuration storage, and confirm acquisition timing through post-route static timing analysis. Power sequencing and I/O voltage selection must follow the device bank rules for every connected peripheral.
Recomendado
Embedded Communications Bridge
The XC7A50T-L1CSG325I can implement protocol conversion, packet buffering, and parallel-to-serial interface bridging in compact communications equipment. Its 52,160 logic cells allow multiple protocol engines and buffering functions to coexist, while 150 I/O support parallel backplanes, status signals, and external memory interfaces. A -1 timing closure is appropriate when the design does not require the additional margin of a faster speed grade. Keep high-speed transceiver traces away from sensitive configuration and reference-clock paths, provide continuous return-plane references, and validate protocol timing after each device or constraint change.
Recomendado
Data Acquisition System
The XC7A50T-L1CSG325I supports compact data-acquisition designs requiring digital triggering, channel control, timestamp management, and data transfer. Its 150 I/O can accommodate parallel sensor outputs and control signals, while the programmable fabric can implement custom filtering or preprocessing without a separate fixed-function controller. The -1 grade and industrial suffix align with applications where temperature reliability and repeatable timing are important. Engineer the design with separate analog and digital return paths, matched-length clock routing, and defined acquisition-window timing. Confirm every I/O standard, drive strength, and bank-voltage combination before fabrication because the 150 I/O are not electrically interchangeable.
Recomendado
Programmable Logic Prototype
The XC7A50T-L1CSG325I is well suited to prototypes that need substantial programmable logic, multiple external interfaces, and a package already common in Artix-7 designs. A 52,160-cell device can host processor peripherals, bus bridges, and custom accelerators while 150 I/O expose enough connectivity for experimentation. The CSG325 footprint also enables controlled migration among compatible Artix-7 density and speed options after design review. Keep the prototype board's power rails, clocking, configuration storage, and JTAG access standards-based so that later migration changes the bitstream and constraints more often than the physical PCB.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para XC7A50T-L1CSG325I — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | XC7A50T-1CSG325I | XC7A50T-2CSG325I | XC7A50T-1CSG325C | XC7A50T-2CSG325C | XC7A50T-3CSG325I |
|---|---|---|---|---|---|---|
| Brand | AMD | AMD | AMD | AMD | AMD | AMD |
| Package | CSG325, 324-ball CSPBGA | CSG325, 324-ball CSPBGA | CSG325, 324-ball CSPBGA | CSG325, 324-ball CSPBGA | CSG325, 324-ball CSPBGA | CSG325, 324-ball CSPBGA |
| Logic Cells | 52,160 cells | 52,160 cells | 52,160 cells | 52,160 cells | 52,160 cells | 52,160 cells |
| User I/O | 150 I/O | 150 I/O | 150 I/O | 150 I/O | 150 I/O | 150 I/O |
| Process Technology | 28 nm | 28 nm | 28 nm | 28 nm | 28 nm | 28 nm |
| Speed Grade | -1 | -1 | -2 | -1 | -2 | -3 |
| Temperature Grade | Industrial | Commercial | Industrial | Commercial | Commercial | Industrial |
Diferenciadores clave
- Industrial temperature-grade identity (frente a XC7A50T-1CSG325I)
- Same-footprint speed-grade flexibility (frente a XC7A50T-2CSG325I)
- Complete package identity for PCB reuse (frente a XC7A50T-3CSG325I)
Notas de diseño
Use the AMD Artix-7 CSG325 package pinout files and UG475 conventions before assigning any BGA ball. Create separate net classes for clocks, high-speed serial links, and ordinary I/O; assign via fields and layer transitions to the FPGA package rather than using general-purpose routing. Maintain uninterrupted reference planes beneath clock and differential pairs, and place decoupling capacitance directly at the associated supply balls. A ball-map error on a 324-ball package can defeat otherwise correct high-level design.
Plan the core, auxiliary, and I/O supply rails as a coordinated power tree rather than independent regulators. Follow the manufacturer power-sequencing diagram, account for configuration behavior during ramp-up, and verify absolute maximum, minimum, and steady-state limits for every rail. For the -1 device, the core-supply range is listed as 0.95 V to 1.05 V. Confirm bank-voltage compatibility for all connected peripherals and calculate worst-case power across temperature, utilization, and clock activity.
Treat the 1098 MHz figure as a device-class timing reference rather than a guaranteed interface rate for every design. Constrain clock-capable input routing, use the most appropriate clock-capable ball, and include realistic board, package, and peripheral uncertainty in timing analysis. For source-synchronous or differential interfaces, derive trace-length and impedance constraints from the selected I/O standard, account for connector and via effects, and verify eye or timing margin rather than relying only on RTL simulation.
Do not treat a different speed or temperature suffix as an automatic functional substitution. A commercial-grade replacement may fail the product's environmental requirements even when its PCB footprint is identical, while a faster grade may change timing and power behavior. Before migration, compare the exact AMD ordering information, regenerate constraints, recompile the design, perform static timing analysis, and check configuration memory, termination, and bank constraints. No cross-manufacturer pin-compatible alternative is established for this device.
Información de cumplimiento
No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified in the listed sources. The I suffix identifies the industrial temperature grade but does not by itself establish AEC-Q100 qualification.