XMC4500F144K1024ACXQMA1 - 120MHz Cortex-M4 MCU | Infineon
N.º de pieza: XMC4500F144K1024ACXQMA1 ✓ ActivoXMC4500F144K1024ACXQMA1 Descripción general
An ARM Cortex-M4 microcontroller is a 32-bit embedded processing device built around the Cortex-M4 processor core. The MCU hierarchy extends from a general-purpose microcontroller to a real-time embedded controller, with integrated flash, SRAM, digital peripherals, communication interfaces, and interrupt control. Infineon positions the XMC4500 within its XMC4000 family for energy-efficient industrial applications requiring configurable peripherals and Ethernet support.
The principal device features include a 120 MHz maximum operating frequency, 1 MB of flash organized as 1M x 8, and 160 kByte of SRAM. Its 144-pin LQFP package provides access to the extensive XMC4500 peripheral set while supporting compact industrial control-board layouts. The ordering designation identifies an industrial-grade XMC4500 configuration with 1024 kByte flash and the XQMA1 package and qualification suffix.
The device combines high-frequency Cortex-M4 processing with on-chip memory and a configurable peripheral set. This architecture allows software-defined control functions, communication protocols, and application-specific interfaces to coexist on one component. Ethernet connectivity makes the microcontroller suitable for embedded gateways and industrial network nodes where local control and network communication must be combined without a separate protocol processor.
Typical uses include industrial Ethernet controllers, factory automation equipment, networked motor and motion-control systems, building automation interfaces, and industrial communications gateways. The 120 MHz processing rate supports responsive protocol handling and control-loop execution, while 1024 kByte flash provides room for networking stacks, control firmware, diagnostics, and configuration data.
PCB designers should assign all 144 package pins directly from the pin-description and package tables in the Infineon XMC4500 datasheet. They should also preserve the manufacturer's recommendations for supply decoupling, clock circuitry, analog interfaces, and exposed-package routing. Firmware must be tested against the exact ordering designation because suffix changes can represent differences in grade, temperature range, qualification, or package configuration.
This product page combines the Infineon ordering information, family-level electrical characteristics, package details, and practical replacement guidance into an engineering-focused resource. It supports component identification, board redesign, firmware planning, and cross-reference work for engineers evaluating the XMC4500F144K1024ACXQMA1 in industrial embedded systems.
Alternativas directas para XMC4500F144K1024ACXQMA1 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con XMC4500F144K1024ACXQMA1 (mismo factor de forma y huella) — difiere en Flash Memory, Product Type, Core Count, Package, Package Type.
XMC4500-F144K1024-AB
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
XMC4500F144F1024ACXQMA1
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
XMC4500E144X1024ACXQSA1
✅ Sustitución directaConsulte el precio
Ver hoja de datos →XMC4800F144F1024AAXQMA1
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
XMC4500F144K1024ACXQMA1 Valores máximos y características eléctricas
| Product Type | 32-bit industrial microcontroller |
| Processor Core | ARM Cortex-M4 |
| Frecuencia de reloj máxima | 120 MHz |
| Flash Memory | 1024 kByte (1M x 8) |
| SRAM | 160 kByte |
| Architecture | 32-bit |
| Ethernet Support | Yes |
| Core Count | 1 |
| Encapsulado | PG-LQFP-144 |
| Número de pines | 144 |
| Package Pitch | 0.5 mm |
| Tipo de montaje | Surface Mount |
| Industrial Temperature Qualification | Industrial grade |
Guía de configuración de pines de XMC4500F144K1024ACXQMA1 0.5 mm
Configuración de pines para XMC4500F144K1024ACXQMA1 (encapsulado 0.5 mm). Este CI digital incluye GPIO, interfaces de comunicación (UART, SPI, I2C) y pines de alimentación. Consulte la hoja de datos del fabricante para conocer las funciones alternativas de los pines y las opciones de configuración. Esencial para el diseño de sistemas embebidos y el diseño de PCB.
No hay datos detallados de patillaje disponibles para XMC4500F144K1024ACXQMA1.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
XMC4500F144K1024ACXQMA1 es adecuado para 6 aplicacións: Industrial Ethernet Gateway, Factory Automation Controller, Networked Motor Controller, Building Automation Interface, Embedded Communications Gateway, Industrial Data Logger.
Industrial Ethernet Gateway
The XMC4500F144K1024ACXQMA1 fits an industrial Ethernet gateway because it combines a 120 MHz ARM Cortex-M4 core, Ethernet connectivity, 1024 kByte flash, and 160 kByte SRAM. The processor can execute protocol conversion, device management, diagnostics, and local control tasks without requiring a separate communications processor. Its 144-pin LQFP package also provides access to the family's configurable digital peripherals. Use the Infineon pin-description table to assign Ethernet PHY, reset, clock, and digital I/O connections, and validate startup sequencing in firmware.
Recomendado
Factory Automation Controller
The XMC4500F144K1024ACXQMA1 is appropriate for factory automation because its 120 MHz Cortex-M4 core supports responsive control logic while the XMC4000 peripheral set can be configured for industrial interfaces. The 1024 kByte flash provides space for control software, fieldbus or Ethernet stacks, and diagnostics, while 160 kByte SRAM supports protocol buffers. Place the device in the 144-pin LQFP footprint only after assigning every signal from the Infineon package table, and reserve clean routing for clock, reset, and communication interfaces.
Recomendado
Networked Motor Controller
A networked motor-control design can use the XMC4500F144K1024ACXQMA1 to combine real-time control, status monitoring, and Ethernet command exchange in one industrial controller. Its 120 MHz Cortex-M4 performance provides headroom for control loops alongside communication tasks, and the 1024 kByte flash can hold motion logic and network firmware. The designer must allocate the required timer, PWM, feedback, and digital interfaces according to the exact XMC4500 package table, then validate timing and fault handling under worst-case network traffic.
Recomendado
Building Automation Interface
The XMC4500F144K1024ACXQMA1 can serve as the communications and supervisory controller in a building automation interface. Ethernet connectivity supports centralized configuration and reporting, while the Cortex-M4 core executes protocol handling and local I/O logic. Its 1024 kByte flash accommodates device firmware, configuration data, and update handling, and the 160 kByte SRAM supports message buffering. For deployment, confirm the exact suffix-specific temperature and qualification requirements and route all 144 package pins from the Infineon datasheet.
Recomendado
Embedded Communications Gateway
The XMC4500F144K1024ACXQMA1 is well suited to an embedded communications gateway requiring network connectivity and configurable local control. The 120 MHz Cortex-M4 processor can manage Ethernet traffic, protocol conversion, diagnostics, and application logic, while 1024 kByte flash provides sufficient code storage for embedded networking stacks. Its industrial 144-pin LQFP package supports a conventional surface-mount design. Engineers should validate PHY interface requirements, clock stability, reset behavior, and peripheral assignments against the manufacturer documentation.
Recomendado
Industrial Data Logger
The XMC4500F144K1024ACXQMA1 can act as an industrial data logger by collecting sensor and machine-state information, processing it locally, and forwarding it over Ethernet. Its 120 MHz Cortex-M4 core leaves processing headroom for protocol management, while 1024 kByte flash supports application code and 160 kByte SRAM provides working and buffering space. A practical implementation should use the manufacturer's recommended clock and decoupling arrangements, maintain deterministic peripheral timing, and protect nonvolatile configuration through the board's appropriate storage implementation.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para XMC4500F144K1024ACXQMA1 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | XMC4500-F144K1024-AB | XMC4500F144F1024ACXQMA1 | XMC4500E144X1024ACXQSA1 | XMC4800F144F1024AAXQMA1 |
|---|---|---|---|---|---|
| Manufacturer | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Package | PG-LQFP-144 | PG-LQFP-144 | PG-LQFP-144 | PG-LQFP-144 | PG-LQFP-144 |
| Flash Memory | 1024 kByte | 1024 kByte | 1024 kByte | 1024 kByte | 1024 kByte |
| Number of Pins | 144 | 144 | 144 | 144 | 144 |
| Ordering Code | XMC4500F144K1024ACXQMA1 | XMC4500-F144K1024-AB | XMC4500F144F1024ACXQMA1 | XMC4500E144X1024ACXQSA1 | XMC4800F144F1024AAXQMA1 |
Diferenciadores clave
- Combines high-frequency control and Ethernet communications in one industrial MCU (frente a XMC4800F144F1024AAXQMA1)
- Matches the closest documented XMC4500 package variant in core, memory, and pin count (frente a XMC4500-F144K1024-AB)
- Provides 160 kByte SRAM for local control and communication buffering (frente a XMC4500F144F1024ACXQMA1)
- Retains the 144-pin LQFP industrial controller footprint (frente a XMC4500E144X1024ACXQSA1)
Notas de diseño
Assign all 144 LQFP positions from the Infineon package pin-description table before routing the PCB. Keep the 0.5 mm package geometry and pad design consistent with the manufacturer's recommended footprint, and verify the exposed or unused thermal and supply pins against the exact ordering designation. A symbol that matches the family block diagram but omits package-specific multiplexing can create board-level failures that software cannot correct.
Use the manufacturer's recommended supply-pin connections and decoupling arrangement for the exact XMC4500 configuration. Place the required bypass capacitors close to their associated power pins and keep high-current return paths short. Because the exact operating supply range and capacitor values were not stated in the product summaries, take those values directly from the Infineon XMC4500 datasheet and reference schematic before release.
Do not treat a shared 144-pin package as sufficient evidence that every XMC4500 or XMC4800 ordering code is interchangeable. Compare the complete ordering table, package pinout, temperature range, qualification, flash organization, SRAM, peripheral set, and startup behavior. Validate firmware and PCB changes together, especially when moving between XMC4500 F, E, X, and K suffix variants or between XMC4500 and XMC4800 families.
Plan clock and reset routing against the Infineon reference layout, keeping sensitive timing paths short and away from noisy switching nodes. Ethernet and other high-speed interfaces require continuous reference planes, controlled return paths, and manufacturer-recommended termination or PHY topology. Because detailed rise-time, impedance, and layout values are not stated in the product summary, use the family datasheet and interface guidance as the controlling references.
Información de cumplimiento
The product information identifies an industrial XMC4500 microcontroller but does not explicitly state the requested material-compliance or automotive-qualification statuses. Obtain current declarations for the exact ordering code.