XMC4500F144K1024ACXQMA1 - 120MHz Cortex-M4 MCU | Infineon
MPN: XMC4500F144K1024ACXQMA1 ✓ 啟用中XMC4500F144K1024ACXQMA1 概覽
An ARM Cortex-M4 microcontroller is a 32-bit embedded processing device built around the Cortex-M4 processor core. The MCU hierarchy extends from a general-purpose microcontroller to a real-time embedded controller, with integrated flash, SRAM, digital peripherals, communication interfaces, and interrupt control. Infineon positions the XMC4500 within its XMC4000 family for energy-efficient industrial applications requiring configurable peripherals and Ethernet support.
The principal device features include a 120 MHz maximum operating frequency, 1 MB of flash organized as 1M x 8, and 160 kByte of SRAM. Its 144-pin LQFP package provides access to the extensive XMC4500 peripheral set while supporting compact industrial control-board layouts. The ordering designation identifies an industrial-grade XMC4500 configuration with 1024 kByte flash and the XQMA1 package and qualification suffix.
The device combines high-frequency Cortex-M4 processing with on-chip memory and a configurable peripheral set. This architecture allows software-defined control functions, communication protocols, and application-specific interfaces to coexist on one component. Ethernet connectivity makes the microcontroller suitable for embedded gateways and industrial network nodes where local control and network communication must be combined without a separate protocol processor.
Typical uses include industrial Ethernet controllers, factory automation equipment, networked motor and motion-control systems, building automation interfaces, and industrial communications gateways. The 120 MHz processing rate supports responsive protocol handling and control-loop execution, while 1024 kByte flash provides room for networking stacks, control firmware, diagnostics, and configuration data.
PCB designers should assign all 144 package pins directly from the pin-description and package tables in the Infineon XMC4500 datasheet. They should also preserve the manufacturer's recommendations for supply decoupling, clock circuitry, analog interfaces, and exposed-package routing. Firmware must be tested against the exact ordering designation because suffix changes can represent differences in grade, temperature range, qualification, or package configuration.
This product page combines the Infineon ordering information, family-level electrical characteristics, package details, and practical replacement guidance into an engineering-focused resource. It supports component identification, board redesign, firmware planning, and cross-reference work for engineers evaluating the XMC4500F144K1024ACXQMA1 in industrial embedded systems.
直接替換替代品,適用於 XMC4500F144K1024ACXQMA1 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: XMC4500F144K1024ACXQMA1 (相同外形與佔位) — 差異在於 Flash Memory, Product Type, Core Count, Package, Package Type.
XMC4500-F144K1024-AB
✅ 直接替換📋 參考替代品(不在目錄中)
XMC4500F144F1024ACXQMA1
✅ 直接替換📋 參考替代品(不在目錄中)
XMC4500E144X1024ACXQSA1
✅ 直接替換聯絡詢價
查看資料表 →XMC4800F144F1024AAXQMA1
✅ 直接替換📋 參考替代品(不在目錄中)
XMC4500F144K1024ACXQMA1 最大額定值與電氣特性
| Product Type | 32-bit industrial microcontroller |
| Processor Core | ARM Cortex-M4 |
| 最大時脈頻率 | 120 MHz |
| Flash Memory | 1024 kByte (1M x 8) |
| SRAM | 160 kByte |
| Architecture | 32-bit |
| Ethernet Support | Yes |
| Core Count | 1 |
| 封裝 | PG-LQFP-144 |
| 腳位數 | 144 |
| Package Pitch | 0.5 mm |
| 安裝類型 | Surface Mount |
| Industrial Temperature Qualification | Industrial grade |
XMC4500F144K1024ACXQMA1 0.5 mm 腳位配置指南
XMC4500F144K1024ACXQMA1(0.5 mm 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: XMC4500F144K1024ACXQMA1.
請參閱 資料表 以查看完整腳位配置。
典型應用
XMC4500F144K1024ACXQMA1 適用於 6 應用s: Industrial Ethernet Gateway, Factory Automation Controller, Networked Motor Controller, Building Automation Interface, Embedded Communications Gateway, Industrial Data Logger.
Industrial Ethernet Gateway
The XMC4500F144K1024ACXQMA1 fits an industrial Ethernet gateway because it combines a 120 MHz ARM Cortex-M4 core, Ethernet connectivity, 1024 kByte flash, and 160 kByte SRAM. The processor can execute protocol conversion, device management, diagnostics, and local control tasks without requiring a separate communications processor. Its 144-pin LQFP package also provides access to the family's configurable digital peripherals. Use the Infineon pin-description table to assign Ethernet PHY, reset, clock, and digital I/O connections, and validate startup sequencing in firmware.
推薦
Factory Automation Controller
The XMC4500F144K1024ACXQMA1 is appropriate for factory automation because its 120 MHz Cortex-M4 core supports responsive control logic while the XMC4000 peripheral set can be configured for industrial interfaces. The 1024 kByte flash provides space for control software, fieldbus or Ethernet stacks, and diagnostics, while 160 kByte SRAM supports protocol buffers. Place the device in the 144-pin LQFP footprint only after assigning every signal from the Infineon package table, and reserve clean routing for clock, reset, and communication interfaces.
推薦
Networked Motor Controller
A networked motor-control design can use the XMC4500F144K1024ACXQMA1 to combine real-time control, status monitoring, and Ethernet command exchange in one industrial controller. Its 120 MHz Cortex-M4 performance provides headroom for control loops alongside communication tasks, and the 1024 kByte flash can hold motion logic and network firmware. The designer must allocate the required timer, PWM, feedback, and digital interfaces according to the exact XMC4500 package table, then validate timing and fault handling under worst-case network traffic.
推薦
Building Automation Interface
The XMC4500F144K1024ACXQMA1 can serve as the communications and supervisory controller in a building automation interface. Ethernet connectivity supports centralized configuration and reporting, while the Cortex-M4 core executes protocol handling and local I/O logic. Its 1024 kByte flash accommodates device firmware, configuration data, and update handling, and the 160 kByte SRAM supports message buffering. For deployment, confirm the exact suffix-specific temperature and qualification requirements and route all 144 package pins from the Infineon datasheet.
推薦
Embedded Communications Gateway
The XMC4500F144K1024ACXQMA1 is well suited to an embedded communications gateway requiring network connectivity and configurable local control. The 120 MHz Cortex-M4 processor can manage Ethernet traffic, protocol conversion, diagnostics, and application logic, while 1024 kByte flash provides sufficient code storage for embedded networking stacks. Its industrial 144-pin LQFP package supports a conventional surface-mount design. Engineers should validate PHY interface requirements, clock stability, reset behavior, and peripheral assignments against the manufacturer documentation.
推薦
Industrial Data Logger
The XMC4500F144K1024ACXQMA1 can act as an industrial data logger by collecting sensor and machine-state information, processing it locally, and forwarding it over Ethernet. Its 120 MHz Cortex-M4 core leaves processing headroom for protocol management, while 1024 kByte flash supports application code and 160 kByte SRAM provides working and buffering space. A practical implementation should use the manufacturer's recommended clock and decoupling arrangements, maintain deterministic peripheral timing, and protect nonvolatile configuration through the board's appropriate storage implementation.
推薦
推薦產品摘要
工程參考資料,適用於 XMC4500F144K1024ACXQMA1 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | XMC4500-F144K1024-AB | XMC4500F144F1024ACXQMA1 | XMC4500E144X1024ACXQSA1 | XMC4800F144F1024AAXQMA1 |
|---|---|---|---|---|---|
| Manufacturer | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Package | PG-LQFP-144 | PG-LQFP-144 | PG-LQFP-144 | PG-LQFP-144 | PG-LQFP-144 |
| Flash Memory | 1024 kByte | 1024 kByte | 1024 kByte | 1024 kByte | 1024 kByte |
| Number of Pins | 144 | 144 | 144 | 144 | 144 |
| Ordering Code | XMC4500F144K1024ACXQMA1 | XMC4500-F144K1024-AB | XMC4500F144F1024ACXQMA1 | XMC4500E144X1024ACXQSA1 | XMC4800F144F1024AAXQMA1 |
主要差異化特點
- Combines high-frequency control and Ethernet communications in one industrial MCU (對比XMC4800F144F1024AAXQMA1)
- Matches the closest documented XMC4500 package variant in core, memory, and pin count (對比XMC4500-F144K1024-AB)
- Provides 160 kByte SRAM for local control and communication buffering (對比XMC4500F144F1024ACXQMA1)
- Retains the 144-pin LQFP industrial controller footprint (對比XMC4500E144X1024ACXQSA1)
設計說明
Assign all 144 LQFP positions from the Infineon package pin-description table before routing the PCB. Keep the 0.5 mm package geometry and pad design consistent with the manufacturer's recommended footprint, and verify the exposed or unused thermal and supply pins against the exact ordering designation. A symbol that matches the family block diagram but omits package-specific multiplexing can create board-level failures that software cannot correct.
Use the manufacturer's recommended supply-pin connections and decoupling arrangement for the exact XMC4500 configuration. Place the required bypass capacitors close to their associated power pins and keep high-current return paths short. Because the exact operating supply range and capacitor values were not stated in the product summaries, take those values directly from the Infineon XMC4500 datasheet and reference schematic before release.
Do not treat a shared 144-pin package as sufficient evidence that every XMC4500 or XMC4800 ordering code is interchangeable. Compare the complete ordering table, package pinout, temperature range, qualification, flash organization, SRAM, peripheral set, and startup behavior. Validate firmware and PCB changes together, especially when moving between XMC4500 F, E, X, and K suffix variants or between XMC4500 and XMC4800 families.
Plan clock and reset routing against the Infineon reference layout, keeping sensitive timing paths short and away from noisy switching nodes. Ethernet and other high-speed interfaces require continuous reference planes, controlled return paths, and manufacturer-recommended termination or PHY topology. Because detailed rise-time, impedance, and layout values are not stated in the product summary, use the family datasheet and interface guidance as the controlling references.
合規資訊
The product information identifies an industrial XMC4500 microcontroller but does not explicitly state the requested material-compliance or automotive-qualification statuses. Obtain current declarations for the exact ordering code.