محصولات (44,000+)

INA210BQDCKRQ1 - AEC-Q100 26V Bi-Directional Current Sense Amp | TI
INA210BQDCKRQ1

INA210BQDCKRQ1 - AEC-Q100 26V Bi-Directional Current Sense Amp | TI

The Texas Instruments INA210BQDCKRQ1 is an AEC-Q100 qualified, 26 V, bi-directional, high-precision current sense amplifier (also called a current-shunt monitor) housed in a 6-pin SOT-SC70 (DCK) package. It senses voltage drops across shunt resistors at common-mode voltages from -0.3 V to 26 V, independent of the supply voltage, and delivers an analog output proportional to the sensed current with a fixed gain of 200 V/V. A current sense amplifier is a specialized analog building block that converts a small differential voltage developed across a current-sense (shunt) resistor into a ground-referenced, amplified output voltage. It sits in the signal chain between the shunt resistor (placed in series with the load) and the downstream ADC, microcontroller, or comparator, and belongs to the broader hierarchy of instrumentation amplifiers -> operational amplifiers -> analog ICs. Zero-drift chopper-stabilized topology enables the INA210 family to achieve microvolt-level offset and excellent common-mode rejection. Key features include a maximum offset voltage of 35 uV, a gain error of only 0.5 percent (max), and 40 kV/us slew rate, plus a 2.7 V to 26 V supply range with 65 uA typical quiescent current. The device offers bidirectional sensing (REF input allows positive or negative current measurement), operates from -40C to +125C, and integrates EMI filtering plus thermal shutdown. The SC70-6 package occupies roughly 2.1 mm x 1.45 mm of PCB area, ideal for compact automotive modules. The INA210 uses a chopper-stabilized input stage and precision thin-film resistors to achieve gain accuracy and ultra-low offset drift over temperature. Its high common-mode rejection ratio (CMRR) of 140 dB and the ability to operate with the input common-mode above V+ make it tolerant of inductive loads, motor inrush, and 12 V/24 V automotive transients such as load-dump. Typical applications include automotive body electronics (battery management, ECU power monitoring), motor control current loops, solenoid and valve actuation feedback, USB Type-C current advertisement (BC 1.2), and precision 48 V telecom/industrial rails. The combination of AEC-Q100 qualification, wide common-mode range, and small package makes it especially well-suited for safety-relevant automotive systems. When designing with this device, place the shunt resistor close to the input pins to minimize parasitic resistance, use Kelvin connection to the shunt, and add a small RC filter at the output to limit noise bandwidth. Choose the shunt value so that the maximum differential input (Vshunt_max = VSENSE_max / 200) does not exceed the linear input range, accounting for transient overloads. This page synthesizes distributor pricing, same-brand and cross-brand drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ تماس
INA2126P - Dual 36V Micropower Instrumentation Amplifier | Texas Instruments
INA2126P

INA2126P - Dual 36V Micropower Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA2126P is a dual-channel, micropower precision instrumentation amplifier designed for accurate differential-signal acquisition. Each channel uses a two-op-amp architecture and consumes 175 µA of quiescent current, while the device operates from ±1.35 V to ±18 V, equivalent to a 36 V maximum total supply range. The INA2126P provides 250 µV offset performance and is supplied in a 16-pin PDIP package for through-hole PCB designs. An instrumentation amplifier is a specialized analog signal-conditioning IC that amplifies the voltage difference between two inputs while rejecting common-mode interference. The INA2126 family belongs to the instrumentation amplifier hierarchy, which includes differential amplifiers, low-noise analog amplifiers, and broader analog signal-chain ICs. Its differential-input architecture makes it suitable for sensor signals, bridge outputs, and other small-signal measurements where the wanted signal is small relative to an imposed common-mode voltage. The principal features of the INA2126P are its dual-channel configuration, 175 µA per channel quiescent current, 250 µV offset specification, and wide ±1.35 V to ±18 V operating range. Micropower consumption reduces the burden on portable and battery-powered systems, while the wide supply range supports both low-voltage portable instrumentation and higher-voltage industrial measurement systems. The differential architecture also helps preserve signal integrity when the input common-mode voltage is substantially larger than the differential signal being measured. The INA2126 family uses a two-op-amp instrumentation-amplifier topology to provide differential amplification with high input impedance and common-mode rejection. Because the device is intended for precision acquisition rather than high-bandwidth signal processing, designers should use the manufacturer-recommended gain-setting resistor and follow the datasheet layout guidance to minimize gain error and offset contributions. The 16-pin PDIP package favors through-hole prototyping, laboratory instrumentation, and industrial control boards where a surface-mount package is not required. Typical applications include portable sensor acquisition, strain-gauge and bridge excitation systems, battery-powered measurement equipment, industrial process monitoring, medical instrumentation, and low-power data-acquisition systems. In each case, the INA2126P provides a practical way to amplify a differential sensor signal while keeping channel quiescent current at 175 µA. Designers should confirm that input common-mode voltage, output swing, gain, bandwidth, and supply limits satisfy the specific measurement requirements. The primary design consideration is ensuring adequate output headroom and checking the gain-dependent bandwidth and input range. The 250 µV offset specification supports precise measurements, but resistor matching and layout still influence overall system accuracy. Input filtering and guarding can reduce high-frequency interference, while stable reference and excitation arrangements are important for bridge-based sensors. This product page combines the verified Texas Instruments product information, distributor availability references, pricing context, package details, and engineering selection guidance to provide a practical comparison point for engineers evaluating the INA2126P.

RFQ تماس
INA2126PA - Dual 36V Micropower Instrumentation Amplifier | Texas Instruments
INA2126PA

INA2126PA - Dual 36V Micropower Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA2126PA is a dual-channel precision instrumentation amplifier designed for accurate, low-noise differential-signal acquisition. The device operates from a wide ±1.35 V to ±18 V supply range, consumes approximately 175 μA per channel, and provides a 16-pin PDIP package for through-hole PCB designs. Its two-amplifier architecture is intended to amplify small differential signals while rejecting common-mode interference in sensor, measurement, and portable instrumentation systems. An instrumentation amplifier is a specialized amplifier category used for differential measurement. Its internal signal path amplifies the difference between two inputs while providing high common-mode rejection, making it more suitable for bridge sensors, current loops, and low-level analog front ends than a general-purpose operational amplifier. The INA2126 belongs to the INAx126 family of precision instrumentation amplifiers, combining low power consumption with accurate signal conditioning. Key characteristics include a 250 μV offset specification, low quiescent current, a wide operating voltage range, and a bandwidth of approximately 200 kHz according to the product listing. The dual configuration provides two independent amplifier channels in one package, reducing component count on multi-axis or multi-sensor boards. The instrument amplifier category is part of the broader linear amplifier hierarchy and ultimately belongs to the analog integrated-circuit and signal-conditioning ecosystem. The INA2126PA is suitable for portable instrumentation, sensor-interface circuits, battery-powered measurement equipment, industrial process monitoring, and precision data-acquisition systems. Its low 175 μA per-channel current makes it useful when battery life and thermal performance are important. The wide supply range also supports systems operating from low-voltage portable rails or higher-voltage industrial analog rails. Designers should pay attention to input common-mode range, output swing, gain-setting resistor selection, bypass-capacitor placement, and the effects of source impedance when using precision instrumentation amplifiers. The dual package provides an opportunity to place two channels close together, but differential routing must minimize noise pickup and maintain a consistent ground reference. Use the manufacturer datasheet for the complete electrical characteristics and pin configuration before laying out a new PCB. This product page combines the INA2126PA device specifications, sourcing information, verified drop-in alternatives, comparison parameters, and practical design guidance to support faster component selection and implementation.

RFQ تماس
INA2126PG4 - Dual 200 kHz Micropower INA | Texas Instruments
INA2126PG4

INA2126PG4 - Dual 200 kHz Micropower INA | Texas Instruments

The Texas Instruments INA2126PG4 is a dual-channel, micropower precision instrumentation amplifier designed for accurate differential signal acquisition. It operates from ±1.35 V to ±18 V, or 1.35 V to 36 V across the supply range, and provides a bandwidth of 200 kHz. The device combines a two-op-amp instrumentation-amplifier architecture with very low quiescent current of 175 µA per channel, making it suitable for portable measurement systems, industrial sensor interfaces, battery-powered equipment, and low-power data-acquisition designs. The INA2126PG4 is packaged in a 16-pin PDIP package. An instrumentation amplifier is a precision analog signal-conditioning IC that amplifies the difference between two input voltages while rejecting common-mode interference. The INA2126 belongs to the instrumentation-amplifier hierarchy of analog ICs and is designed to provide high input impedance, low offset voltage, and accurate differential gain. Its two-op-amp design provides a practical balance between low power consumption and signal fidelity, making it useful when common-mode noise, source impedance, or limited supply energy restricts simpler amplifier arrangements. The INA2126PG4 is specified with 175 µA per-channel quiescent current, up to 250 µV maximum offset voltage, 83 dB CMRR, and 200 kHz bandwidth according to the Texas Instruments product information. The device also supports a supply voltage from 1.35 V to 36 V, allowing operation from low-voltage portable systems through higher-voltage industrial rails. Its dual-channel configuration permits simultaneous acquisition of two differential signals, reducing the number of separate instrumentation amplifiers required on a measurement board. The two-op-amp architecture is intended for accurate, low-noise differential-signal acquisition. Input bias current is listed as 10 nA in product information, helping preserve accuracy when connected to high-impedance sensors. The 0.4 V/µs slew rate supports amplification of changing sensor signals, while the 200 kHz bandwidth covers many pressure, temperature, strain, and low-frequency industrial measurement applications. The instrumentation-amplifier function converts a small differential input into a larger single-ended signal for an ADC or downstream measurement circuit. Typical uses include portable medical and laboratory instruments, low-power industrial controllers, battery-operated sensor interfaces, bridge and thermocouple signal conditioning, and general-purpose data-acquisition systems. The dual architecture is especially useful when two channels must be acquired at similar signal levels, such as paired strain-gauge or pressure-sensor channels. Design engineers should select external gain and filtering components to match the sensor output, required bandwidth, and input common-mode range. For layout, keep input and feedback components close to the corresponding pins and maintain a symmetric differential signal path. Place decoupling capacitors near the supply pins and route high-impedance input traces away from switching nodes and digital return currents. Verify the actual gain equation, common-mode range, output swing, and supply limits against the manufacturer datasheet before production release. This page combines Texas Instruments product specifications, package information, sourcing guidance, and practical design notes for engineers evaluating the INA2126PG4.

RFQ تماس
INA2126U - 36V Dual Micropower Instrumentation Amplifier | Texas Instruments
INA2126U

INA2126U - 36V Dual Micropower Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA2126U is a dual-channel, 36 V micropower precision instrumentation amplifier with 250 µV offset, 175 µA quiescent current per channel, and a 16-pin SOIC package. It supports a wide ±1.35 V to ±18 V operating range and is designed for accurate, low-noise differential-signal acquisition. The device provides a gain range of 5 to 10000, a typical gain-bandwidth product of 200 kHz, and a typical input noise density of 0.4 nV/√Hz at 1 kHz. An instrumentation amplifier is a precision analog signal-conditioning IC that converts a small differential input into a single-ended or differential output. Its internal gain stage rejects common-mode interference and permits accurate measurement of low-level sensor signals. In the product hierarchy, an instrumentation amplifier belongs to the amplifier IC family, specifically the precision measurement and signal-conditioning category. It is distinct from a general-purpose operational amplifier because it integrates input buffering, differential subtraction, and gain-setting resistors. The INA2126U combines a gain range of 5 to 10000 with low offset and low noise. Its 250 µV maximum input offset supports accurate measurements at relatively high gain, while the 0.4 nV/√Hz typical noise density helps preserve weak-signal information. Two amplifiers are provided in each package, making the device useful when a system needs two independent differential measurement channels without using two separate packages. The two-op-amp architecture keeps quiescent current to 175 µA per channel, which is important in battery-powered equipment. The 200 kHz typical gain-bandwidth product provides useful bandwidth for slow sensor signals rather than high-speed video or communications signals. An operating supply of ±1.35 V to ±18 V allows operation from low-voltage portable rails through ±15 V industrial measurement systems, subject to the device's 36 V maximum total supply range. Typical uses include battery-powered portable instrumentation, low-level bridge and transducer measurement, industrial sensor acquisition, precision current sensing, and differential signal conditioning. The dual-channel organization can support two sensors in one instrument, while the micropower operation reduces the effect of the amplifier on battery life. Input common-mode and output swing limits must still be checked against the intended sensor and supply rails. Designers should use the gain-setting resistors and input common-mode network specified by the manufacturer, keep sensitive input traces short, and provide suitable bypassing close to the supply pins. The input network must also avoid excessive imbalance between the differential inputs because that can affect common-mode rejection and gain accuracy. Output loading and downstream ADC acquisition time should be evaluated together. This page combines manufacturer specifications, verified distributor availability, and practical comparison guidance with same-package alternatives. It also identifies missing pricing, pin-definition, environmental, and compliance details instead of estimating them, supporting faster component selection for precision analog designs.

RFQ تماس
INA2126UA - Dual 36V Micropower INA | Texas Instruments
INA2126UA

INA2126UA - Dual 36V Micropower INA | Texas Instruments

Texas Instruments INA2126UA is a dual-channel precision instrumentation amplifier with a 36 V maximum supply, 175 µA quiescent current per channel, and 250 µV input offset voltage in a 16-pin SOIC (D) package. It is designed for accurate, low-noise differential-signal acquisition where low power and common-mode rejection are important. An instrumentation amplifier is a specialized analog amplifier that combines differential input measurement, high input impedance, and accurate gain-setting in one package. Within the signal-chain hierarchy, it sits between sensors or bridge networks and higher-level ADC, control, or monitoring systems. Its differential architecture rejects common-mode interference while preserving the small voltage variations being measured. The INA2126UA provides two amplifier channels, a 5 V/V to 10,000 V/V programmable gain range, and a gain error of no more than 0.04%. A typical input offset of 250 µV supports precision measurements, while the low 175 µA-per-channel quiescent current suits battery-powered and portable instrumentation. The device operates across an extended temperature range of -40°C to +85°C. Internally, the INA2126 family uses a two-op-amp instrumentation-amplifier architecture. This structure provides a practical balance between low power, low noise, common-mode rejection, and user-programmable gain. The external resistor between the RG pins establishes the differential gain, allowing one device to serve multiple measurement ranges without changing the analog front end architecture. Typical uses include bridge-transducer signal conditioning, portable measurement systems, battery-powered diagnostic equipment, industrial sensor interfaces, and low-current precision sensing. Its differential inputs are particularly useful when the source includes substantial common-mode voltage or interference relative to the wanted signal. Design the layout around the RG resistor, input filtering, and supply grounding. Place the gain-setting resistor close to the device, provide adequate bypassing on both supply rails, and maintain a quiet return path to minimize errors that can dominate microvolt-level measurements. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks and checking exposed alternatives. This product page combines the manufacturer specifications with practical selection guidance, application analysis, pin-package context, and a parameter-by-parameter comparison. It is intended to help engineers identify whether the INA2126UA fits a low-power precision measurement design and how closely related same-family devices compare.

RFQ تماس
INA2126UG4 - 36V Dual Micropower Instrumentation Amplifier | TI
INA2126UG4

INA2126UG4 - 36V Dual Micropower Instrumentation Amplifier | TI

The Texas Instruments INA2126UG4 is a dual 36 V micropower precision instrumentation amplifier with 175 µA quiescent current per channel, 250 µV offset, and differential-signal measurement capability in a 16-pin SOIC package. Its low power consumption and broad supply range suit battery-powered instrumentation, portable measurement systems, and low-current industrial sensors. An instrumentation amplifier is a signal-conditioning IC that amplifies the voltage difference between two input terminals while rejecting common-mode interference. The INA2126 belongs to the precision instrumentation amplifier hierarchy and supports accurate differential-signal acquisition. Its two-op-amp architecture combines low quiescent current with a wide operating-voltage range of ±1.35 V to ±18 V. Key features include 175 µA of quiescent current per channel, 250 µV offset, and operation from a single 2.7 V supply or from dual ±18 V rails. The device is intended for low-level differential measurements where battery life, signal integrity, and compactness are important. Two channels in one package can reduce board area when multiple sensor inputs must be conditioned. The 36 V maximum supply gives designers substantial transient and common-mode headroom in industrial environments, although the input common-mode range remains dependent on the selected supply and gain configuration. The precision-oriented internal architecture is intended to preserve small differential signals while reducing supply and common-mode errors. Designers should review gain, input range, output swing, and supply limits in the manufacturer datasheet before fixing system operating conditions. Typical uses include bridge-sensor interfaces, current-shunt measurements, portable multimeter circuits, battery-powered sensor acquisition, medical monitoring equipment, and industrial process-control inputs. The low 175 µA-per-channel quiescent current is particularly valuable in portable systems where amplifier current directly affects available battery runtime. Decoupling and layout are critical because the instrument-amplifier pins connect directly to low-level sensor signals. Place the supply bypass capacitor close to the positive and negative supply pins, connect the input return paths close to the amplifier, and use the differential inputs symmetrically. Validate the complete gain, common-mode range, output swing, noise, and settling-time combination on the target board.

RFQ تماس
INA2128P - Dual Precision Instrumentation Amplifier | TI
INA2128P

INA2128P - Dual Precision Instrumentation Amplifier | TI

The Texas Instruments INA2128P is a dual, low-power instrumentation amplifier with two independent amplifiers, a gain range of 1 to 10,000, and a 200 kHz bandwidth at a gain of 100. The device is offered in a 16-pin PDIP package. Its precision characteristics include 50 uV maximum offset voltage, 0.5 uV/degree C maximum input offset drift, 5 nA maximum input bias current, and 120 dB minimum common-mode rejection. An instrumentation amplifier is a differential analog signal-conditioning IC that amplifies the voltage difference between two inputs while rejecting common-mode interference. In the signal-chain hierarchy, an instrumentation amplifier is a specialized amplifier, a precision analog front end, and an active analog integrated circuit. The INA2128P uses a three-op-amp arrangement and current-feedback input circuitry to preserve useful bandwidth even when relatively high gain is selected. A single external resistor sets the gain from 1 to 10,000, simplifying adjustment during design and calibration. The 200 kHz bandwidth available at gain 100 supports accurate amplification of sensors and low-frequency measurement signals without requiring the bandwidth of a high-speed instrumentation amplifier. Input protection extending to plus or minus 40 V also helps control fault energy applied to the input pins, although it does not eliminate the need for normal application-level protection. The INA2128P provides two amplifier circuits in one package, allowing a dual-channel design to reduce board area and component count. Its low offset voltage and low drift are particularly useful when the amplified differential signal is small relative to the measurement resolution. The specified 120 dB minimum common-mode rejection helps suppress noise and voltage that appears equally on both inputs, while the low 5 nA maximum input bias current suits high-impedance sources. Typical uses include bridge-sensor signal conditioning, portable instrumentation, biomedical measurement, industrial process monitoring, and two-channel sensor acquisition. The device can also amplify differential outputs from transducers where low offset and common-mode rejection are more important than wide-bandwidth conversion performance. Designers should follow the manufacturer datasheet for the gain-setting resistor, supply bypassing, input protection, and pin assignments. The power-supply range is plus or minus 18 V, so both positive and negative rails are permitted when the circuit requires bipolar input or output ranges. Decoupling capacitors should be placed close to the supply pins, and source impedance should remain compatible with the amplifier's bias-current and bias-voltage requirements. This page combines verified manufacturer and distributor information with package-aware alternatives, application guidance, and engineering-focused selection notes. It also separates verified INA2128P data from parameters that require confirmation in the full datasheet, helping engineers plan a board revision without treating incomplete data as guaranteed specifications.

RFQ تماس
INA2128PA - Dual Instrumentation Amplifier | Texas Instruments
INA2128PA

INA2128PA - Dual Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA2128PA is a dual, low-power, general-purpose instrumentation amplifier with gains from 1 to 10,000, a 16-pin PDIP package, and operation over -40°C to +85°C. It uses a current-feedback input architecture to maintain a bandwidth of 200 kHz at a gain of 100, while providing low offset voltage, low offset drift, high common-mode rejection, and input protection to ±40 V. An instrumentation amplifier is a precision analog signal-conditioning IC that amplifies the difference between two input voltages while rejecting signals common to both inputs. Its internal three-op-amp architecture supports accurate differential measurements from low-level sensors. Within the broader semiconductor hierarchy, an instrumentation amplifier belongs to the amplifier IC and analog signal-conditioning categories, where it sits between a sensor or bridge and a measurement, control, or data-conversion system. Key features include a maximum offset voltage of 50 µV, maximum offset drift of 0.5 µV/°C, maximum input bias current of 5 nA, and minimum common-mode rejection of 120 dB. A single external resistor sets the gain from 1 to 10,000. The dual configuration provides two independent amplifier channels, allowing one package to serve differential measurements or multiple sensor inputs. The current-feedback input circuitry is the principal performance feature. Unlike a voltage-feedback instrumentation amplifier that loses bandwidth as gain increases, the INA2128 family retains useful bandwidth at high closed-loop gain; the specified bandwidth is 200 kHz at gain 100. The three-op-amp topology also makes the input bias-current behavior relatively insensitive to source impedance, which is valuable when the source is a strain gauge, thermocouple, bridge, or other high-impedance sensor. Typical applications include bridge-based pressure and load-cell measurements, biomedical instrumentation, current-loop sensing, precision data acquisition, and low-level differential signal conditioning. The ±40 V input protection expands the usable fault-tolerance range, but it does not permit operation beyond the device's stated supply-voltage ratings. Designers should still limit input transients and maintain common-mode voltage within the operating region described by the manufacturer datasheet. The primary design consideration is gain-setting resistor selection because the external resistor determines gain while also affecting bandwidth, noise, and allowable operating range. Place the gain-setting resistor close to the corresponding gain resistor pins, maintain symmetrical input routing, provide adequate supply bypassing, and use a stable reference ground. This page combines device specifications, application guidance, lifecycle information, and drop-in alternative evaluation for faster engineering selection. For a dual-channel instrumentation amplifier where PCB area is limited, the INA2128PA provides a direct fit in a 16-pin PDIP footprint. The through-hole package also supports prototype and industrial repair workflows where a surface-mount assembly process would add unnecessary handling complexity.

RFQ تماس
INA2128U - Dual Precision Instrumentation Amplifier | TI
INA2128U

INA2128U - Dual Precision Instrumentation Amplifier | TI

The Texas Instruments INA2128U is a dual, low-power, general-purpose instrumentation amplifier packaged in a 16-pin SOIC. It uses a versatile three-op-amp architecture and current-feedback input circuitry to support broad bandwidth even at high gain. A single external gain-setting resistor provides gains from 1 to 10,000, while the two independent amplifier channels support simultaneous differential measurements or dual-channel sensing. An instrumentation amplifier is a specialized analog amplifier designed to measure small differential voltages accurately in the presence of large common-mode voltages. Its typical signal-chain hierarchy is differential input -> instrumentation amplifier -> precision analog measurement or control system. The INA2128U supports input-referenced and ground-referenced sensing, where unwanted signals common to both inputs are rejected while the differential component is amplified. The principal benefits of the INA2128U are its dual-channel configuration, selectable gain from 1 to 10,000, and bandwidth of 200 kHz at a gain of 100. Current-feedback input circuitry helps preserve usable bandwidth as gain increases. The low-power architecture is suitable for compact analog measurement systems, portable instrumentation, and industrial equipment where two precision analog channels must fit into a small board area. Internally, each channel follows a three-op-amp instrumentation-amplifier topology. Differential input currents are directed toward internal feedback paths, while a single external resistor establishes the gain relationship. Because the circuit supports both single-ended and differential input arrangements, engineers can adapt it to sensor bridges, shunt measurements, and bipolar input signals. The dual organization also allows synchronized acquisition of two related signals without requiring two separate packages. Typical uses include medical instrumentation, industrial sensor interfaces, battery-powered measurement equipment, current-shunt monitoring, and precision data-acquisition systems. Differential inputs are particularly useful when a sensor produces a small voltage riding on a larger common-mode voltage. Pairing the two channels can also support gain-and-offset measurement, comparator-style monitoring, or sampled systems requiring closely matched amplifier paths. A practical design must account for the external gain resistor, input and output settling, reference-ground connection, supply decoupling, and common-mode range. Place the gain-setting resistor close to the device and use the manufacturer's recommended layout and decoupling guidance. Maintain the input and output common-mode voltages within the operating limits, and verify system settling at the highest gain required by the measurement bandwidth. This product page organizes the manufacturer's functional description, package information, comparison considerations, and application guidance into one engineering-focused resource. It also identifies where pin-level and qualification details must be checked in the manufacturer datasheet before a new board is released to production.

RFQ تماس
INA2128U/1K - Dual Instrumentation Amplifier | Texas Instruments
INA2128U/1K

INA2128U/1K - Dual Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA2128U/1K is a dual, low-power instrumentation amplifier with two independent signal channels, selectable gain from 1 to 10,000, and a 16-pin SOIC package. It accepts bipolar input signals, provides a bandwidth of 200 kHz at a gain of 100, and operates from dual power supplies up to ±18 V. A single external gain resistor sets the gain of each channel. An instrumentation amplifier is a specialized amplifier-and-op-amp category designed to amplify small differential signals while rejecting common-mode interference. Its internal three-op-amp architecture provides high input impedance, symmetrical differential inputs, accurate gain control, and straightforward scaling of sensor outputs. Within the broader semiconductor hierarchy, the INA2128 belongs to the precision analog amplifier class and is used as a front-end signal-conditioning component between sensors or measurement networks and data converters. Key features include two independent amplifiers on one die, a gain range of 1 to 10,000, and current-feedback input circuitry that maintains useful bandwidth at higher gain. The 200 kHz bandwidth quoted at gain 100 makes the device suitable for sensors whose signals must be measured with limited filtering. Its dual-channel arrangement also reduces board area when two independent measurements are required, such as sensing a bridge output and a reference voltage. The three-op-amp architecture uses external gain-setting resistors and internal precision circuitry. Because the signal path is differential, common-mode voltage and gain errors can be rejected more effectively than with a single ordinary op-amp stage. Designers must nevertheless consider resistor tolerance, input common-mode range, output swing, supply headroom, and stability when adding input and output filtering capacitors. Typical applications include bridge and strain-gauge front ends, industrial pressure and temperature measurement, portable instrumentation, biomedical instrumentation, and precision current sensing. The dual-channel configuration is particularly useful when a system must amplify two low-level differential signals with closely matched electrical characteristics. For reliable operation, keep input and output components close to their associated pins, use a low-noise supply arrangement, and verify that the common-mode and output voltages remain inside the device operating limits. The gain resistor should use an appropriate tolerance and temperature coefficient for the required measurement accuracy. Stable reference or sensor grounding is also essential because excessive ground gradients can appear directly as measurement error. This page combines manufacturer specifications, package and ordering information, validated replacement candidates, application guidance, and design notes to provide a practical engineering reference for the INA2128U/1K.

RFQ تماس
INA2128UA - Dual Precision Instrumentation Amplifier | Texas Instruments
INA2128UA

INA2128UA - Dual Precision Instrumentation Amplifier | Texas Instruments

Texas Instruments INA2128UA is a dual, low-power instrumentation amplifier with two independent channels, gain adjustment from 1 to 10,000 using one external resistor, and a 16-pin SOIC package. Each channel provides a maximum offset voltage of 50 uV, maximum offset drift of 0.5 uV/degree C, maximum input bias current of 5 nA, and a minimum common-mode rejection ratio of 120 dB. An instrumentation amplifier is a differential-input amplifier optimized for measuring small signals superimposed on larger common-mode voltages. Its internal three-op-amp architecture provides matched input stages, high differential input impedance, accurate gain control, and strong common-mode rejection. This makes the INA2128 suitable for sensor interfaces where a low-level differential signal must be amplified accurately in the presence of substantial DC voltage, industrial noise, or ground-potential differences. The INA2128 combines low offset and drift with a minimum 120 dB CMRR. Input overload protection extends to plus or minus 40 V, helping the amplifier tolerate accidental large input transients. Its supply range of 2.25 V to 18 V supports single-supply and dual-supply instrumentation systems. A single external resistor selects the gain, reducing the number of precision components needed for adjustable measurement channels. The versatile three-op-amp design uses current-feedback input circuitry to preserve bandwidth at higher gains. According to the Texas Instruments datasheet, bandwidth remains 200 kHz at a gain of 100. This combination of precision DC behavior and usable high-gain bandwidth makes the device suitable for bridge sensors, current measurement, biomedical instrumentation, and industrial data-acquisition systems. Typical uses include low-voltage pressure and strain-signal conditioning, thermocouple and RTD amplification, current-shunt measurement, battery-cell monitoring, and precision analog-front-end designs. The two-channel configuration is especially useful when a system must process two related sensor inputs while maintaining consistent gain-setting and supply architecture across both channels. Choose gain resistors with suitable tolerance and temperature coefficient, and verify common-mode headroom at the lowest supply voltage. Input and reference pins require careful layout because leakage, parasitic resistance, and asymmetric copper can degrade CMRR. The gain-setting resistor should be placed close to the device, with symmetrical input routing where practical. This product overview combines manufacturer specifications, package details, application guidance, and drop-in replacement information to support faster component selection and PCB planning. It also identifies the trade-offs involved when changing amplifier families, including gain range, bandwidth, offset performance, supply voltage, and protection requirements.

RFQ تماس
INA2128UG4 - Dual Instrumentation Amplifier | Texas Instruments
INA2128UG4

INA2128UG4 - Dual Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA2128UG4 is a dual, low-power instrumentation amplifier with two independent amplifier channels, gain settings from 1 to 10,000, and bandwidth of 200 kHz at a gain of 100. The device is packaged in a 16-pin SOIC and is specified for operation from -40°C to +85°C. An instrumentation amplifier is a precision analog signal-conditioning IC that amplifies the voltage difference between two inputs while rejecting common-mode signals. Its internal three-op-amp architecture provides a practical combination of high input impedance, accurate differential gain, and common-mode rejection. This places the INA2128UG4 in the hierarchy of instrumentation amplifier, analog signal conditioner, amplifier IC, and semiconductor. The principal features include a dual-channel configuration, low-power operation, user-programmable gain from 1 to 10,000 using one external resistor, and current-feedback input circuitry that maintains useful bandwidth at high gain. These characteristics suit sensor outputs, bridge-based measurements, biomedical instrumentation, and analog signal chains where small differential signals must be measured accurately in the presence of larger common-mode voltages. The three-op-amp topology separates differential input handling from the gain-setting network, helping simplify circuit design and reduce external component count. A single gain resistor establishes the selected gain, while internal input and feedback stages provide the required signal amplification. The result is a versatile general-purpose instrumentation amplifier that can serve both precision measurement and general instrumentation applications. Typical uses include pressure and temperature sensor interfaces, strain-gauge and Wheatstone bridge excitation, biomedical signal acquisition, current-shunt measurement, laboratory instrumentation, and low-level analog front ends. The dual architecture allows two independent sensor channels in one package, reducing board area when both channels are required. Designers should place the gain-setting resistor close to the gain pins, observe the input and output common-mode limits, and decouple the supply pins according to the manufacturer datasheet. Input and output filtering should be selected for the required bandwidth because excessive capacitance can affect stability and phase margin. The operating temperature range also requires thermal verification for the complete board assembly. This product page combines the INA2128UG4 device identity, package and gain details with practical application guidance, same-family alternatives, and a parameter-focused comparison. It is designed to help engineers locate the datasheet, verify pin compatibility, understand bandwidth constraints, and plan an instrumentation front end before requesting a quote.

RFQ تماس
INA2132U - Dual 36V Difference Amplifier | Texas Instruments
INA2132U

INA2132U - Dual 36V Difference Amplifier | Texas Instruments

The Texas Instruments INA2132U is a dual, low-power, single-supply difference amplifier operating from 2.7 V to 36 V and providing two matched amplifier channels in a 14-pin SOIC package. Its input stage supports common-mode voltages from -15 V to 28 V, while a minimum common-mode rejection ratio of 76 dB helps reject equal-magnitude signals applied to both inputs. The device operates over a -40 °C to 85 °C temperature range and is suitable for industrial measurement, sensing, and signal-conditioning systems. A difference amplifier measures the voltage between two input nodes rather than amplifying a single node relative to ground. In the signal-chain hierarchy, the INA2132U is a difference amplifier, which is a subtype of instrumentation amplifier, and ultimately belongs to the broader amplifier and analog signal-conditioning categories. The dual-channel configuration allows one package to handle two differential sensing channels while maintaining consistent amplifier characteristics between them. Key features include the 2.7 V to 36 V single-supply operating range, 76 dB minimum common-mode rejection, and a -40 °C to 85 °C industrial temperature rating. The low-power architecture is appropriate for systems in which every milliampere affects battery life, thermal rise, or analog headroom. A common-mode range extending below ground makes the device useful in shunt-monitoring systems where the signal may be referenced to a supply rail rather than to ground. The INA2132U is designed for differential measurements where the useful information is small compared with the common-mode voltage. Both amplifier channels are implemented in the same device, which supports matched measurements and reduces the number of external packages required. Its SOIC package also supports conventional surface-mount assembly, although exposed-pad thermal management is not specified in the available ordering information. Typical applications include high-side or low-side current sensing, bridge-sensor signal conditioning, battery monitoring, industrial process measurement, and differential voltage acquisition. When designing around this part, verify the signal amplitude, common-mode limits, and output-swing requirements against the application before committing the footprint. This page combines manufacturer product information, verified distributor pricing and availability, and engineering guidance that goes beyond a basic distributor listing. It also documents where additional datasheet parameters are required so engineers can distinguish confirmed values from information that must still be checked against the manufacturer datasheet.

RFQ تماس
INA2132UA - Dual 36V Difference Amp | Texas Instruments
INA2132UA

INA2132UA - Dual 36V Difference Amp | Texas Instruments

Texas Instruments INA2132UA is a dual-channel, low-power, single-supply difference amplifier with a 2.7 V to 36 V supply range, 76 dB minimum common-mode rejection, and a 14-pin SOIC package. Each channel amplifies the voltage difference between two input pins while rejecting common-mode signals, making the device suitable for precision bridge sensing, current measurement, and industrial signal-conditioning systems. A difference amplifier is a specialized amplifier architecture that subtracts two input voltages and multiplies the result by a defined gain. Its role within the amplifier hierarchy is amplifier IC to instrumentation amplifier to low-power difference amplifier. Internal precision resistors establish the nominal gain, while the amplifier rejects signals common to both inputs. This architecture reduces errors in sensor systems where a small differential signal is superimposed on a larger common-mode voltage. The INA2132UA provides two amplifier channels, a common-mode input range extending from -15 V to 28 V, and a bandwidth of approximately 3 MHz. Its 36 V maximum supply capability supports higher-voltage industrial systems. The 14-pin SOIC package allows straightforward surface-mount assembly, while the -40 °C to +85 °C operating range supports industrial temperature environments. Each channel combines a precision operational-amplifier core with a laser-trimmed resistor network. This construction supports consistent gain and common-mode rejection without requiring external gain-setting resistors. Because both channels are integrated into one package, designers can use the two amplifiers for complementary measurement channels, differential sensing, or two-stage signal conditioning within the same circuit. Typical uses include Wheatstone-bridge sensor front ends, motor-current monitoring, differential voltage measurement, and industrial process-control inputs. The common-mode rejection characteristic is particularly useful when the desired signal is much smaller than the voltage shared by both input terminals. The approximately 3 MHz bandwidth also allows the amplifier to process signals beyond static or very slow sensor outputs. When designing the circuit, verify that input, output, and supply voltages remain within their operating limits at every temperature and tolerance corner. Keep sensitive input routing short, maintain symmetric layouts around the differential pair, and use stable reference and bypass connections to minimize offset and noise errors. A single-supply design also requires careful review of the output common-mode range when the amplified difference can approach either supply rail. This page consolidates manufacturer specifications, package details, application guidance, and same-footprint replacement information into a design-oriented resource for engineers evaluating the INA2132UA.

RFQ تماس
INA2133U - Dual 1.5MHz Precision Difference Amplifier | TI
INA2133U

INA2133U - Dual 1.5MHz Precision Difference Amplifier | TI

Texas Instruments INA2133U is a dual-channel, unity-gain precision difference amplifier built around laser-trimmed precision resistor networks. The verified manufacturer information identifies a 1.5 MHz bandwidth, a maximum offset voltage of 450 µV, approximately 0.95 mA of power consumption, and a 14-pin SOIC package. These characteristics position the INA2133U as a high-speed instrumentation amplifier for measuring small differential signals superimposed on larger common-mode voltages. A difference amplifier is an analog signal-conditioning IC that subtracts two input voltages and amplifies the resulting differential component. In the broader electronics hierarchy, it belongs to the instrumentation-amplifier family, which sits within precision analog amplifiers, analog ICs, and semiconductors. Such devices are commonly used to reject common-mode interference, amplify sensor outputs, and preserve signal integrity between sensors and analog-to-digital converters. The INA2133U provides two precision difference amplifiers in one 14-pin SOIC package. Its 1.5 MHz bandwidth supports signal acquisition beyond very slow sensor applications, while the 450 µV maximum offset specification limits input-referred error during low-level measurements. The low 0.95 mA power figure also makes it relevant to compact industrial, communications, and test equipment where each milliampere affects thermal and power-budget requirements. According to the Texas Instruments product page, the device is designed for high-speed precision differential signal conditioning. Internally, the INA2133 combines a precision operational-amplifier core with an on-chip, laser-trimmed resistor network. The manufacturer describes the INA133 and INA2133 families as unity-gain difference amplifiers using high-slew-rate precision operational amplifiers. Laser trimming improves resistor matching and gain accuracy, while matched resistor temperature coefficients help preserve common-mode rejection and gain accuracy over temperature. The dual-channel implementation reduces package count when two independent differential measurements are required. Typical uses include current-sense and low-voltage bridge measurements, industrial sensor interfaces, communications-line signal conditioning, precision test equipment, and differential inputs to data converters. The 1.5 MHz bandwidth is particularly useful when the measured differential signal must be captured without the long settling delays associated with lower-bandwidth instrumentation amplifiers. The 450 µV offset specification should nevertheless be evaluated against the smallest signal amplitude that the application expects to measure. When designing around the INA2133U, check input common-mode range, output swing, supply voltage, gain configuration, and the input/output network required by the selected operating mode. Place the device close to the signal source, maintain short differential traces, and use a quiet return path so that connector or routing noise does not degrade the differential measurement. Decoupling capacitors should be positioned at the supply pins according to the manufacturer application guidance. This page combines the verified manufacturer specifications, current distributor availability, same-family drop-in options, application guidance, and practical design notes. It also distinguishes verified INA2133U characteristics from parameters that still require confirmation from the complete manufacturer datasheet or application-specific calculations.

RFQ تماس
INA2133UA - Dual 1.5MHz Difference Amplifier | Texas Instruments
INA2133UA

INA2133UA - Dual 1.5MHz Difference Amplifier | Texas Instruments

Texas Instruments INA2133UA is a dual, unity-gain precision difference amplifier with 1.5 MHz bandwidth, 450 µV maximum offset voltage, and approximately 0.95 mA power consumption. The device is supplied in a 14-pin SOIC package and is intended for measuring small differential signals in the presence of large common-mode voltages. Its two amplifier channels support independent differential measurements when board space, power, and signal conditioning requirements favor integration. A difference amplifier is a specialized amplifier IC that subtracts two input voltages and amplifies the resulting differential signal. Its internal resistor network establishes the gain and improves common-mode rejection when the paired resistors track closely over temperature. The INA2133 belongs to the difference-amplifier hierarchy, where precision difference amplifier is a subtype of instrumentation amplifier and analog signal-conditioning IC. The manufacturer describes the INA2133 as a high-speed, precision difference amplifier built from a precision operational amplifier and a laser-trimmed resistor network. The INA2133UA provides a maximum input offset voltage of 450 µV, low offset-voltage drift, and maximum gain error of 0.05%. Its 1.5 MHz bandwidth supports higher-frequency signal paths than a slow precision difference amplifier while retaining the gain accuracy required for bridge and sensor measurements. The integrated resistor network is designed for accurate gain and high common-mode rejection. Excellent resistor temperature-coefficient tracking helps maintain gain accuracy and common-mode rejection over temperature. The dual configuration allows two matched differential channels in one package, reducing board area compared with two separate single-channel devices. The manufacturer also offers the related INA133 family in the same high-speed precision difference-amplifier datasheet. Typical uses include bridge-transducer signal extraction, differential sensor measurement, current-shunt monitoring, instrumentation, and factory-automation signal conditioning. The device is particularly suitable when a small differential voltage must be measured in the presence of a larger common-mode voltage and when a unity-gain difference-amplifier implementation would otherwise require several passive and active components. Design the input network, output reference, supply bypassing, and grounding to preserve common-mode rejection and bandwidth. Keep input and feedback routes compact, place bypass capacitors close to the supply pins, and use a low-noise reference for applications that require an output referenced to ground or another system voltage. Confirm the complete pin assignment and operating limits against the manufacturer datasheet before layout release. This product page combines the manufacturer device description, package and ordering information, sourcing availability, strict drop-in alternative screening, and practical design guidance. It also distinguishes directly verifiable INA2133UA characteristics from parameters that require confirmation against the complete manufacturer datasheet before a new design is released.

RFQ تماس
INA2134PA - Dual 0dB Audio Differential Receiver | Texas Instruments
INA2134PA

INA2134PA - Dual 0dB Audio Differential Receiver | Texas Instruments

The Texas Instruments INA2134PA is a dual audio differential line receiver with a fixed gain of 1 V/V, low distortion of 0.0005% at 1 kHz, and a 14 V/µs slew rate. The device is supplied in a 14-pin PDIP package for through-hole audio and instrumentation designs. Each channel uses high-performance operational amplifiers with on-chip precision resistors to convert balanced differential inputs into single-ended audio signals. An audio differential line receiver is a specialized amplifier stage that rejects common-mode noise present on balanced signal pairs while preserving the wanted differential audio voltage. Its place in the signal-chain hierarchy is differential receiver → balanced audio input amplifier → analog signal-conditioning front end. This makes the INA2134PA particularly useful when a stereo source uses balanced left and right channels but the downstream circuitry requires ground-referenced, single-ended audio signals. Key performance characteristics include a fixed 0 dB voltage gain, 90 dB minimum CMRR, 2.9 mA maximum quiescent current, and operation from -18 V to +18 V. According to the TI INA134 and INA2134 datasheet, the receiver combines low distortion with fast settling and wide output-voltage swing. The 14 V/µs slew rate supports accurate reproduction of high-level, high-frequency transients rather than clipping them under moderate loading. The INA2134PA contains two independent receiver channels and internal precision gain-setting resistors. On-chip resistors reduce component count and help maintain consistent channel-to-channel gain without requiring external matched networks. Its differential architecture is useful for rejecting ground-potential differences and coupled interference present between a source and the receiving equipment, especially in professional audio, instrumentation, and industrial control systems. Typical uses include stereo balanced-to-unbalanced conversion, audio measurement front ends, line-level signal conditioning, and instrumentation amplifiers. Because the gain is fixed at 1 V/V, downstream stages must provide any required attenuation or additional amplification. The device is also appropriate for prototypes, repairs, and legacy equipment where a standard 14-pin PDIP footprint and through-hole assembly are preferred over a surface-mount package. When laying out the receiver, connect the balanced input conductors to their assigned differential inputs and route the outputs to the following analog stage with short traces and a stable ground reference. Decouple each supply rail close to the device, keep input and output nodes away from switching-current paths, and verify the output swing against the selected load. This page also organizes package, electrical, and replacement information for faster component selection.

RFQ تماس
INA2134UA - 0dB Audio Differential Receiver | Texas Instruments
INA2134UA

INA2134UA - 0dB Audio Differential Receiver | Texas Instruments

The Texas Instruments INA2134UA is a dual-channel audio differential line receiver with a fixed 1 V/V gain, low distortion, and high slew rate, housed in a 14-pin SOIC package. The receiver is designed for professional audio and other balanced-signal applications where common-mode rejection and signal integrity are important. A differential receiver is an analog signal-conditioning circuit that accepts a pair of complementary or balanced inputs and produces a single output proportional to their difference. The INA2134 family uses high-performance operational amplifiers with on-chip precision resistors. This integrated approach simplifies balanced audio input design and reduces the need for external matched resistor networks. Its differential architecture is part of the broader special-purpose amplifier and signal-conditioning IC hierarchy. The INA2134UA provides 0.0005% distortion at 1 kHz, a 14 V/µs slew rate, and a fixed gain of 1 V/V. The manufacturer specifies a wide supply range of ±18 V and low quiescent current of 2.9 mA maximum. Its high common-mode rejection helps reject shared noise and interference on balanced audio lines, while fast settling and slew-rate performance support dynamic audio signals. The device is offered in single and dual versions, with INA2134UA providing two receiver channels. The 14-pin SOIC package provides a practical surface-mount option for balanced audio preamplifiers, mixer stages, instrument interfaces, and other low-frequency analog systems. The INA2134UA is also specified for operation from -40°C to +85°C, covering the extended industrial temperature range. When using the INA2134UA, preserve the balanced signal path and connect the appropriate input and output decoupling capacitors close to the device pins. Verify source impedance, output loading, cable termination, and common-mode voltage before finalizing the analog layout. Proper grounding and symmetrical routing are important for maximizing common-mode rejection and minimizing distortion. This product page combines the manufacturer specifications, sourcing guidance, drop-in alternatives, application fit, and practical PCB considerations to support faster component selection and design review. It is intended to help engineers identify the correct package, compare suitable alternatives, and implement a stable balanced-audio front end without treating the receiver as a general-purpose precision amplifier.

RFQ تماس
INA2137PA - Dual ±6 dB Audio Receiver | Texas Instruments
INA2137PA

INA2137PA - Dual ±6 dB Audio Receiver | Texas Instruments

Texas Instruments INA2137PA is a dual audio differential line receiver with selectable gain configurations of one-half (1/2, -6 dB) and 2 (+6 dB). The device is packaged as a 14-pin PDIP and is intended for audio and general-purpose differential signal reception. Each receiver channel can reject common-mode noise while extracting the differential signal carried by a balanced line. A differential line receiver is an analog amplifier circuit that compares two input voltages and amplifies their difference. In an audio system, a balanced source sends signal through one conductor and an inverted copy through the other. The receiver rejects voltage shared by both conductors, reducing interference pickup compared with a single-ended input. The INA2137 family is associated with the audio differential line receiver category, the amplifier IC hierarchy, and the broader signal-conditioning and audio interface domain. The INA2137 uses selectable differential gain. Texas Instruments describes a basic one-half gain configuration for differential reception, while reversing the input and feedback resistors produces a gain of 2, corresponding to +6 dB. This arrangement allows a designer to select between attenuation and gain without changing the receiver footprint. The same guidance identifies INA134 and INA2134 as devices intended for unity-gain reception where that behavior is required. The INA2137 family is suitable for professional audio, consumer audio, line-level balanced inputs, instrumentation, and other applications in which a small differential signal must be recovered from a noisy environment. Because the package is a through-hole PDIP, it also supports prototyping and designs assembled with conventional plated-through-hole techniques. Its 14-pin arrangement provides separate positive and negative inputs, output connections, reference pins, and supply connections for two channels. Designers should follow the manufacturer's application schematics when assigning input and feedback resistors. Resistor ratios determine whether each channel operates at one-half gain or a gain of 2. Reference and supply connections must be handled according to the pin-description table in the manufacturer datasheet, particularly when using the reference pins for biasing or output offset management. Decoupling capacitors should be placed close to the device’s supply pins to limit supply-current transients and preserve signal integrity. The INA2137PA is best suited to balanced audio links where -6 dB or +6 dB channel gain is useful and a 14-pin PDIP package fits the assembly process. For unity-gain systems, compare the INA134 or INA2134 families because the INA2137’s documented resistor-configured gains are one-half and 2. This page combines the manufacturer’s device description with practical configuration guidance, package details, sourcing paths, and engineering-oriented replacement analysis.

RFQ تماس
INA2137UA - Dual ±6dB Audio Receiver | Texas Instruments
INA2137UA

INA2137UA - Dual ±6dB Audio Receiver | Texas Instruments

The Texas Instruments INA2137UA is a dual audio differential line receiver with selectable fixed gains of +6 dB and -6 dB, a 14-pin SOIC package, and operation from dual ±18 V supplies. It combines high-performance operational amplifiers with on-chip precision resistors to recover balanced audio signals and reject common-mode interference. An audio differential line receiver is a specialized analog interface that converts a balanced, differential input into a single-ended audio signal. Its functional position is input conditioning: line receiver, differential receiver, analog signal conditioner, and interface IC. Differential reception is particularly useful when two conductors carry the same signal in opposite polarity, allowing common-mode noise to be rejected before the signal reaches an audio-processing or amplification stage. Key features include low distortion of 0.0005% at 1 kHz, a slew rate of 14 V/µs, a fast settling time of 0.01%, and high common-mode rejection of 90 dB. The maximum quiescent current is 2.9 mA, while the wide ±18 V supply range supports conventional professional and consumer audio rails. Each receiver can provide a fixed gain of 1/2 or 2, corresponding to -6 dB or +6 dB. The internal precision-resistor network provides repeatable gain without requiring external gain-setting resistors. This simplifies board design and reduces tolerance-related gain errors. High slew rate preserves large-signal dynamic range in music and speech paths, while low distortion minimizes added harmonic content. The 90 dB CMRR specification helps attenuate hum and interference picked up equally by both input conductors. Typical applications include balanced professional-audio inputs, consumer audio equipment, active speaker systems, audio mixers, and instrumentation interfaces. The dual-channel configuration accommodates left and right channels in one package. The 14-pin SOIC also offers a practical standard footprint for through-hole assembly and conventional surface-mount production. When designing a board around the INA2137UA, preserve the balanced input topology and keep input and return paths appropriately routed. Check output swing, input common-mode range, and gain configuration against the intended signal amplitude. Decoupling capacitors should be placed close to the supply pins, while unused inputs require appropriate treatment according to the manufacturer pin-description table. This product overview combines the device's audio-performance figures, package information, pin and footprint considerations, replacement guidance, and application-level design guidance to support faster component evaluation and board-level implementation.

RFQ تماس
INA213BQDCKRQ1 - 26V Bidirectional Current-Sense IC | TI
INA213BQDCKRQ1

INA213BQDCKRQ1 - 26V Bidirectional Current-Sense IC | TI

The Texas Instruments INA213BQDCKRQ1 is an AEC-Q100 automotive-grade, voltage-output, bidirectional current-shunt monitor rated for common-mode voltages from -0.3V to 26V, packaged in a 6-pin SC-70 DCK package. The device is designed to amplify the small differential voltage produced across a current-sense shunt and convert it into a ground-referenced analog voltage for measurement and control. A current-sense amplifier, also called a current-shunt monitor, is a specialized instrumentation amplifier that measures current indirectly from the voltage drop across a precision shunt resistor. INA213-Q1 belongs to the voltage-output current-shunt-monitor family within instrumentation amplifiers and power-measurement ICs. Its bidirectional measurement supports both positive and negative current flow, making it suitable for motor, battery, automotive, and industrial power-control systems. Verified manufacturer and distributor data identify the INA213BQDCKRQ1 as a 26V, AEC-Q100, high-precision current-sense amplifier. The device supports low-side or high-side measurement, and the official part page identifies the DCK package as a 6-pin SOT-SC70 package. The automotive-grade ordering suffix is consistent with the AEC-Q100 qualification stated by Texas Instruments. The INA21x-Q1 family is intended for applications requiring accurate current measurement across a shunt while the sensed node may sit at a substantially different voltage from the measurement ground. This allows current monitoring in batteries, motor-control systems, electronic loads, power supplies, and automotive electrical systems without placing the shunt at ground potential. The output voltage must remain within the device's valid operating and output limits, so the system designer should verify supply, common-mode, shunt, and output-headroom constraints from the manufacturer datasheet. Typical uses include bidirectional battery-current measurement, DC motor current sensing, solenoid and actuator monitoring, power-supply load current reporting, industrial control input sensing, and automotive load diagnostics. Because the part is bidirectional, it can report charge and discharge current with one signal path rather than requiring separate positive and negative measurement channels. The primary design consideration is the relationship between shunt resistance, sensed current, amplifier gain, input range, and output swing. A higher shunt resistance produces a larger differential signal and can improve measurement resolution, but it also increases power dissipation in the shunt. The PCB should keep the high-current shunt path separate from sensitive input traces, use a low-error reference resistor network, and provide stable supply bypassing close to the device. This page combines verified source data with engineering guidance while clearly identifying parameters that require confirmation from the manufacturer datasheet.

RFQ تماس
INA2141P - Dual G=10/100 Instrumentation Amplifier | Texas Instruments
INA2141P

INA2141P - Dual G=10/100 Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA2141P is a dual, low-power instrumentation amplifier offering selectable gains of 10 and 100 in a 16-pin plastic DIP package. Each amplifier combines low offset voltage, low drift, high common-mode rejection, current-feedback input circuitry, and wide bandwidth for precision analog signal conditioning. The INA2141P is designed for applications that require accurate amplification of differential signals in the presence of substantial common-mode voltage. An instrumentation amplifier is a specialized analog amplifier optimized for measuring low-level differential signals, such as sensor outputs, while rejecting common-mode noise and voltage. Unlike a general-purpose operational amplifier, an instrumentation amplifier provides high input impedance, consistent gain accuracy, and strong common-mode rejection in a single integrated circuit. The INA2141 family is a dual instrumentation amplifier, so one package can process two independent channels. The INA2141P supports two fixed gain settings, 10 and 100, and uses current-feedback input circuitry to maintain bandwidth at higher gain. The manufacturer datasheet states that bandwidth reaches 200 kHz at a gain of 100. Low offset voltage is specified at 50 µV maximum, with maximum drift of 0.5 µV/°C and gain accuracy of ±0.05%. Common-mode rejection reaches 117 dB minimum at a gain of 100. The device accepts supply voltages as low as ±2.25 V and operates with supplies up to ±18 V. Input protection extends to ±40 V, helping the amplifier withstand overload conditions in sensor interfaces and industrial measurement systems. Quiescent current is approximately 750 µA per amplifier, making the device suitable for low-power and battery-operated instrumentation. Typical uses include bridge-sensor and pressure-transducer interfaces, medical monitoring, industrial process measurement, current-loop sensing, and laboratory instrumentation. Because the INA2141P is a dual amplifier, it is especially useful for paired sensors or two-stage measurement systems where board area and power consumption are important. Designers should verify the gain-setting resistor configuration, reference-voltage implementation, input common-mode range, and supply headroom against the datasheet before layout. Decoupling capacitors should be placed close to the supply pins, and the analog input traces should be routed away from switching nodes. The manufacturer datasheet also provides application guidance for gain selection, bandwidth, and input protection. This page combines the verified manufacturer and distributor information for INA2141P with package-level guidance, application context, and design considerations that help engineers evaluate the device alongside alternative instrumentation-amplifier implementations.

RFQ تماس
INA2141PA - Dual G=10/100 Amplifier | Texas Instruments
INA2141PA

INA2141PA - Dual G=10/100 Amplifier | Texas Instruments

The Texas Instruments INA2141PA is a dual, low-power instrumentation amplifier with selectable gains of 10 and 100, supplied in a 16-pin PDIP package. It is designed for conditioning differential sensor signals where high input impedance, accurate differential measurement, and a fixed gain range simplify analog front-end design. The dual configuration provides two instrumentation-amplifier channels on one package. An instrumentation amplifier is a specialized analog signal-conditioning IC that amplifies the voltage difference between two inputs while rejecting signals common to both inputs. Its application hierarchy is instrumentation amplifier, differential amplifier, analog amplifier, signal-conditioning IC, and semiconductor. This makes the INA2141PA appropriate for bridge-based sensing, current measurement, and low-level differential signal acquisition. The INA2141 family offers two supported gain choices, 10 and 100, allowing a designer to select sensitivity according to the expected sensor output. The dual-channel architecture is useful when the system must measure two related quantities, reduce component count, or preserve consistent analog characteristics across channels. Its through-hole PDIP package supports conventional PCB assembly and prototype or repair workflows. According to the manufacturer product page, INA2141 is a low-power instrumentation amplifier intended for precision differential signal conditioning. The device family combines differential input handling with fixed-gain operation, reducing the need for discrete op-amp networks around bridges and sensors. Its dual-channel arrangement also simplifies layout when several low-level signals must be conditioned before conversion or processing. Typical uses include weighing and force sensing, industrial bridge interfaces, current-shunt measurement, biomedical instrumentation, and factory automation. The gain choices make the device useful when a modest input range requires amplification by 10, while a smaller signal such as a millivolt-level bridge output may benefit from the gain-100 setting. For PCB design, place each instrumentation-amplifier channel close to its source to minimize differential pickup and keep high-impedance input routing away from switching nodes. Use a quiet ground reference and follow the manufacturer pin-description table for supply, input, reference, and output connections. Confirm the complete electrical limits, common-mode range, output swing, and recommended external-component values in the manufacturer datasheet. This page organizes the exact package and family information with engineering-oriented application guidance, replacement analysis, comparison fields, and practical layout considerations. It is intended to help engineers confirm fit before committing the INA2141PA to a new sensor-conditioning board.

RFQ تماس