AD711JN - 16 V/us Precision BiFET Op Amp | Analog Devices
MPN: AD711JN ✓ فعالAD711JN نمای کلی
A BiFET operational amplifier is a voltage-feedback amplifier whose differential input stage uses junction field-effect transistors. This BiFET input stage provides high input impedance, low bias currents, and good noise behavior while preserving the voltage-feedback operating characteristics required by precision analog signal chains. In the broader semiconductor hierarchy, the AD711JN belongs to the operational-amplifier, analog-amplifier, and signal-conditioning IC categories.
The AD711J grade emphasizes speed and precision. Its 16 V/us minimum slew rate allows large voltage swings to be reproduced rapidly, while the 3 MHz minimum unity-gain bandwidth provides useful closed-loop bandwidth for moderately fast instrumentation. The specified 0.01% settling performance in 1.0 us is particularly valuable in pulse-amplitude measurement, data conversion, active filtering, and feedback-control circuits where signal accuracy must be maintained shortly after a transition.
Laser wafer trimming is used to control offset voltage and offset-voltage drift, reducing errors that would otherwise be amplified in high-gain stages. The JFET input architecture also avoids the higher input bias currents commonly associated with older bipolar input designs. These characteristics make the amplifier suitable for low-level instrumentation, impedance buffers, audio-frequency signal processing, and feedback elements in higher-gain systems.
Typical uses include precision measurement amplifiers, active filters, sample-and-hold amplifiers, analog-to-digital converter input stages, and general-purpose high-speed voltage-feedback designs. An 8-pin DIP package makes the AD711JN convenient for prototyping, educational equipment, legacy industrial electronics, and repair applications where through-hole construction is preferred over a surface-mount package.
When using the AD711JN, preserve the pin assignments shown in the manufacturer pin description table and place input and feedback components close to the relevant terminals to minimize parasitic feedback. Select external resistors and capacitors for the required closed-loop gain and stability. Account for input- and output-voltage limits, power-supply headroom, and the 16 V/us edge-rate capability when driving capacitive or long interconnects.
This product page combines the manufacturer datasheet, package information, technical alternatives, comparison parameters, and practical circuit guidance. It helps engineers evaluate the AD711JN as a legacy-compatible precision BiFET amplifier while highlighting grade, bandwidth, settling-time, layout, and sourcing considerations that are not communicated by the part number alone.
جایگزینهای drop-in برای AD711JN — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
AD711JNZ
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
AD711KNZ
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
AD711ANZ
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
AD711CNZ
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
AD7111ABNZ
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
AD7111LNZ
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
AD711JN حداکثر مقادیر مجاز و مشخصات الکتریکی
| Product Type | Single precision operational amplifier |
| Input Stage | JFET/BiFET |
| Amplifier Configuration | 1 circuit |
| Slew Rate | 16 V/us minimum for AD711J |
| Unity-Gain Bandwidth | 3 MHz minimum for AD711J |
| Settling Accuracy | 0.01% in 1.0 us |
| Offset Voltage | 0.25 mV maximum |
| Open-Loop Gain | 200 V/mV minimum |
| بستهبندی | 8-pin plastic DIP |
| نوع نصب | Through-hole |
پیکربندی پین AD711JN
| پین 1 | OFFSET NULL — Offset-voltage null terminal |
| پین 2 | IN- — Inverting input |
| پین 3 | IN+ — Non-inverting input |
| پین 4 | V- — Negative supply connection |
| پین 5 | OFFSET NULL — Offset-voltage null terminal |
| پین 6 | OUTPUT — Analog output |
| پین 7 | V+ — Positive supply connection |
| پین 8 | NC — Not connected (per datasheet) |
کاربردهای معمول
AD711JN مناسب است برای 6 کاربردs: Precision Measurement Amplifier, Active Audio Filter, ADC Input Signal Conditioning, Pulse Signal Amplifier, Laboratory Instrumentation Buffer, Industrial Control Feedback.
Precision Measurement Amplifier
The AD711JN fits low-level measurement front ends that require accurate amplification around the dc-to-audio-frequency range. Its minimum 3 MHz unity-gain bandwidth supports useful closed-loop response, while the 16 V/us minimum slew rate permits rapid settling after input steps. The laser-trimmed 0.25 mV maximum offset voltage helps control output error in high-gain instrumentation. Build the amplifier with short, low-leakage input routes, verify bias-current effects against the source impedance, and select the closed-loop noise gain for stable operation. The 0.01% settling specification in 1.0 us is useful when the acquisition system must capture a measurement shortly after a stimulus or calibration event.
پیشنهادی
Active Audio Filter
The AD711JN can implement precision active filters for audio-band signals because it combines a 3 MHz minimum unity-gain bandwidth with a 16 V/us minimum slew rate. These characteristics allow moderate-amplitude signals to cross the filter with limited slew distortion while retaining low-offset behavior from the trimmed input stage. Choose resistor and capacitor values that place poles and zeros within the amplifier's stable operating range, and verify maximum output swing for the intended signal level. Place feedback and compensation components close to the device, and keep the ground-return path short so filter performance is not degraded by shared copper impedance.
پیشنهادی
ADC Input Signal Conditioning
The AD711JN is suitable as the drive or buffer stage preceding a moderately fast analog-to-digital converter when the system requires low offset and rapid settling. Its 3 MHz minimum unity-gain bandwidth handles signal bandwidth below the converter's conversion characteristics, while the 0.01% settling in 1.0 us specification helps reduce timing error during acquisition. Select the amplifier gain so that the converter input range is not exceeded, then confirm the amplifier's output swing at the required logic levels. Keep the feedback network close to the package and route the converter clock and digital signals away from sensitive input and feedback nodes to minimize conversion error.
پیشنهادی
Pulse Signal Amplifier
The AD711JN can amplify pulse-shaped signals when fast edge reproduction and post-transition accuracy are more important than very wideband operation. The AD711J grade offers a minimum 16 V/us slew rate and is specified to settle to 0.01% in 1.0 us. Those characteristics make it appropriate for sampling, thresholding, and loop-feedback circuits where a saturated amplifier would delay the next conversion or control action. Confirm the required output amplitude, load, and allowable settling interval, and use a stable feedback topology with compensation appropriate for the selected closed-loop gain.
پیشنهادی
Laboratory Instrumentation Buffer
The AD711JN provides a practical precision-buffer option for laboratory instruments that combine moderate bandwidth with low-level signal handling. Its JFET input stage supports high source impedance, laser trimming reduces offset error, and the 3 MHz minimum unity-gain bandwidth provides more margin than a slow precision amplifier. Use a unity-gain configuration only when stability is confirmed with the selected load and compensation values. Include input protection, account for input common-mode limits, and route the return connection directly to the analog ground reference to minimize measurement error.
پیشنهادی
Industrial Control Feedback
The AD711JN can be evaluated for industrial feedback loops that require moderate loop bandwidth, low offset, and a through-hole package for serviceable legacy equipment. The amplifier's 16 V/us minimum slew rate helps preserve control-loop phase margin when the loop contains only modest capacitance, while its 3 MHz minimum unity-gain bandwidth is sufficient for many low-bandwidth control signals. The designer must still account for the load, output saturation, supply headroom, and stability at the closed-loop gain. A grounded, shielded implementation should keep motor or relay return currents from sharing sensitive analog-ground paths.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای AD711JN — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | AD711JNZ | AD711KNZ | AD711ANZ | AD7111ABNZ | AD7111LNZ |
|---|---|---|---|---|---|---|
| Package | PDIP-8 | PDIP-8 | PDIP-8 | PDIP-8 | PDIP-8 | PDIP-8 |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Product Type | Single precision BiFET operational amplifier | Single precision BiFET operational amplifier | Single precision BiFET operational amplifier | Single precision BiFET operational amplifier | Single operational amplifier | Single operational amplifier |
| Price Tier | Request a quote | Request a quote | Request a quote | Request a quote | Request a quote | Request a quote |
تفاوتهای کلیدی
- AD711J-grade speed and settling performance (در مقابلAD7111ABNZ)
- Closest order-code alternative (در مقابلAD711JNZ)
- Broader temperature-grade options within the same footprint (در مقابلAD711KNZ)
یادداشتهای طراحی
Place the power-supply bypass capacitors directly between the V+ and V- pins and the appropriate ground return. Keep the loops short and avoid routing sensitive input and feedback traces alongside the output or supply paths. The 3 MHz minimum unity-gain bandwidth makes short feedback paths and clean grounding especially important. A compact analog ground region around pin 8 and the supply bypass capacitors will generally produce more predictable behavior than a broad shared return path.
Design for the AD711J grade's 16 V/us minimum slew rate when driving long PCB traces or cable capacitance. A fast edge can produce overshoot and ringing even when the signal frequency is modest. Terminate the line appropriately for its impedance, keep the amplifier close to the source and load, and use a series resistor close to the output when capacitive loading requires damping. Verify the resulting waveform with an oscilloscope across the full intended load range.
Do not assume that every amplifier with a similar 8-pin package is electrically interchangeable. Confirm the offset null assignments, input polarity, supply connections, and no-connect position against the Analog Devices pin-description table. Also check the selected grade's temperature limits and compare slew rate, bandwidth, offset, input bias current, and supply range before replacing an AD711JN. A footprint match alone does not guarantee circuit-level compatibility.
اطلاعات انطباق
The available manufacturer excerpts do not state the RoHS, REACH, lead-free, halogen-free, or conflict-minerals status for the exact AD711JN order code. AEC-Q100 is not applicable to this general-purpose precision operational amplifier.