AD848JR - 175MHz High-Speed Op Amp | Analog Devices
MPN: AD848JR ✓ فعالAD848JR نمای کلی
A high-speed operational amplifier is a voltage-feedback amplifier designed to process signals with wide bandwidth, low delay, and fast amplitude transitions. Within the analog IC hierarchy, the AD848 belongs to the operational-amplifier and high-speed amplifier families, combining precision biasing, input stages, output drive, and frequency compensation in one monolithic semiconductor. Its gain of at least 5 makes it particularly useful for video, communications, instrumentation, and pulse-shaping stages requiring more bandwidth than general-purpose precision amplifiers provide.
The principal performance features are a 175 MHz gain-bandwidth product, 300 V/s slew rate, and 4.8 mA supply current. The amplifier settles to 0.1% in 80 ns for a 10 V step, making it useful for waveform capture, pulse amplification, and video gain stages. Its input noise density is listed as 3 nV/√Hz, supporting low-noise high-frequency signal conditioning when appropriate source impedance and bandwidth are maintained.
The AD848 uses internal compensation optimized for closed-loop gains of 5 and above. This is an important architectural distinction from decompensated amplifiers that require higher closed-loop gain. The device is positioned for designers who need substantial operating bandwidth without external compensation and who can accept the minimum-gain constraint. The manufacturer also identifies the AD848 as an enhanced replacement for the LM6164 series and as a pin-for-pin replacement for several high-speed amplifiers in gains of 5 or greater.
Typical applications include video preamplification, high-speed instrumentation, communications receive chains, active filtering, pulse shaping, and analog signal conditioning. It can also serve as a high-speed comparator-like stage when operated in its stable gain region, although feedback, bandwidth, and output-swing requirements remain critical. In systems requiring less than unity or gains below 5, the AD849's decompensated architecture or a unity-gain-stable amplifier should be evaluated instead.
Designers should preserve the minimum closed-loop gain of 5, route feedback components close to the device, and verify capacitive-load stability at the intended gain. Input and output decoupling should follow the manufacturer datasheet recommendations. Power-supply bypassing is particularly important in high-speed systems because supply ripple can couple into the output and compromise settling performance.
This product page combines manufacturer specifications, package and pin information, practical circuit guidance, structured comparisons, and verified substitute information. It is designed to help engineers identify whether the AD848JR's gain stability, bandwidth, power consumption, and 8-pin SOIC footprint fit a new design or replacement requirement.
جایگزینهای drop-in برای AD848JR — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
AD848JRZ
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
AD849JR
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
AD847JR
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
AD840JR
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
AD841JR
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
AD848JR حداکثر مقادیر مجاز و مشخصات الکتریکی
| Amplifier Type | Single high-speed operational amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 175 MHz |
| Slew Rate | 300 V/s |
| جریان تغذیه | 4.8 mA |
| Minimum Stable Closed-Loop Gain | 5 |
| Settling Time to 0.1% | 80 ns for a 10 V step |
| Input Noise Density | 3 nV/√Hz |
| Supply Voltage Range | ±4.5 V to ±18 V |
| Maximum Supply Voltage | ±18 V |
| Compensation | Internal compensation |
| بستهبندی | 8-pin SOIC |
| نوع نصب | Surface mount |
پیکربندی پین AD848JR
| پین 1 | OFFSET NULL — Offset adjustment input |
| پین 2 | INVERTING INPUT — Inverting input |
| پین 3 | NONINVERTING INPUT — Non-inverting input |
| پین 4 | V- — Negative supply voltage |
| پین 5 | OFFSET NULL — Offset adjustment input |
| پین 6 | OUTPUT — Analog output |
| پین 7 | V+ — Positive supply voltage |
| پین 8 | NC — Not connected |
کاربردهای معمول
AD848JR مناسب است برای 6 کاربردs: Video Signal Preconditioning, High-Speed Communications Receiver, Precision Instrumentation Front End, Pulse Shaping and Edge Conditioning, Active Filtering and Frequency Shaping, Industrial Test and Measurement.
Video Signal Preconditioning
The AD848JR is well suited to video preamplification because its 175 MHz gain-bandwidth product and 300 V/s slew rate preserve wideband signal transitions. It should be used in a closed-loop gain of at least 5 to maintain the stability established by the internal compensation. Placing the amplifier close to the source and keeping feedback tracks short reduces parasitic feedback and ringing. A properly bypassed dual supply also limits supply-to-output modulation that could otherwise appear as visible video noise or timing instability.
پیشنهادی
High-Speed Communications Receiver
The AD848JR can amplify communications signals when the receiver stage operates at gain 5 or greater. Its 175 MHz gain-bandwidth product supports broadband waveform fidelity, while the 80 ns settling time to 0.1% for a 10 V step supports rapid decision or sampling systems. The 4.8 mA supply current is useful in power-conscious receivers, but the design must still account for input noise density of 3 nV/√Hz and provide clean, decoupled supplies to avoid degrading receiver dynamic range.
پیشنهادی
Precision Instrumentation Front End
For instrumentation requiring a gain of 5 or greater, the AD848JR combines a 175 MHz bandwidth with an 80 ns settling time, enabling rapid acquisition of small signals from sensors and transducers. The 3 nV/√Hz input noise density supports high-frequency measurement work, although actual input-referred noise depends on source impedance, bandwidth, and amplifier configuration. Use short guard traces and controlled grounding around the input stage, and confirm that the selected gain and feedback network meet the required settling specification.
پیشنهادی
Pulse Shaping and Edge Conditioning
The AD848JR's 300 V/s slew rate and 175 MHz gain-bandwidth product make it effective for conditioning edges and preserving pulse shape in instrumentation and test systems. Its internal compensation is appropriate for closed-loop gains of at least 5, avoiding the need for external compensation components in standard non-inverting or inverting configurations. Keep the feedback loop compact and verify output swing for the required pulse amplitude. If the circuit must operate below gain 5, choose a unity-gain-stable member such as the AD847 instead.
پیشنهادی
Active Filtering and Frequency Shaping
The AD848JR can implement active filter stages where the required closed-loop gain is 5 or greater and wide bandwidth is valuable. Its 175 MHz gain-bandwidth product provides more than enough signal path range for many moderate-frequency filter stages, while the 300 V/s slew rate supports large-signal tests. Component tolerances and op-amp behavior remain important at high Q, so simulate the complete filter with its intended feedback network. Maintain short feedback paths and use decoupling close to the supply pins to minimize unintended high-frequency behavior.
پیشنهادی
Industrial Test and Measurement
The AD848JR suits wideband industrial test and measurement systems that need rapid settling and a gain of at least 5. Its 175 MHz gain-bandwidth product, 300 V/s slew rate, and 80 ns settling time support high-speed signal acquisition and conditioning, while dual ±4.5 V to ±18 V operation allows integration with multiple analog front-end levels. Thermal design should account for the package dissipation at sustained output current, and the system should provide stable references and local bypass capacitors. The amplifier's gain threshold must be checked across the complete test range.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای AD848JR — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | AD848JRZ | AD849JR | AD847JR | AD840JR | AD841JR |
|---|---|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Specialized Family Feature | Gain-stable high-speed operation | Same AD848 electrical core | Higher gain-bandwidth product | Unity-gain stability | Greater precision and output-current drive | Greater precision and output-current drive |
تفاوتهای کلیدی
- Provides lower minimum gain than the decompensated family alternative (در مقابلAD849JR)
- Provides substantially more bandwidth than the unity-gain-stable family member (در مقابلAD847JR)
- Maintains the same core performance for lead-free ordering (در مقابلAD848JRZ)
یادداشتهای طراحی
Configure the AD848 only at a closed-loop gain of 5 or greater. Its internal compensation is optimized for that range, and using it as a unity-gain follower can compromise stability. Before replacing an existing amplifier, confirm that the circuit's lowest operating gain satisfies this requirement. If gain can fall below 5, choose a unity-gain-stable amplifier or use a decompensated device configured in its specified operating range.
Keep the input, output, and feedback paths compact because the 175 MHz bandwidth can couple loop delay, parasitic capacitance, and supply noise into the signal path. Place input and output decoupling capacitors close to their supply pins, use the shortest practical return connection, and avoid routing high-impedance input traces next to fast output nodes. These layout practices reduce ringing and preserve the advertised settling performance.
Use clean dual supplies within the ±4.5 V to ±18 V operating range and verify the total supply span does not exceed 36 V. Decouple each supply rail locally and check that output-current demand and package dissipation remain acceptable at the highest expected signal amplitude. Although the device's listed supply current is 4.8 mA, the design must also account for load-dependent output-current consumption.
Validate capacitive loading, output swing, and feedback stability at the intended gain and signal amplitude. High-speed amplifiers can oscillate when driving long cables, probe capacitance, or other capacitive loads. Start with the manufacturer's recommended feedback topology, add isolation resistors near the output only when necessary, and verify the final board with an oscilloscope rather than relying only on simulation.
اطلاعات انطباق
Formal material-compliance and qualification documents are not stated in the product information. AEC-Q100 is treated as not applicable to this general-purpose operational amplifier ordering code.