ADF4360-1BCP - 2250 MHz Integer-N VCO Synthesizer | Analog Devices
MPN: ADF4360-1BCP ✓ فعالADF4360-1BCP نمای کلی
An integer-N frequency synthesizer is a phase-locked-loop device that locks a voltage-controlled oscillator to a stable reference frequency. It combines a frequency synthesizer, VCO, programmable integer divider, and reference-control functions into one RF component. Within the broader hierarchy, the ADF4360-1BCP is a PLL and frequency synthesizer, then a clock-and-timing IC, and finally a semiconductor for RF signal generation and frequency control.
Key features include fully integrated integer-N operation, programmable output power, a three-wire serial programming interface, digital lock detection, and hardware and software power-down modes. The 3.6 V supply and 1.8 V logic compatibility simplify connections to low-voltage control systems. The divide-by-2 option is valuable when a lower RF frequency is required without adding a separate output divider.
The device uses a closed-loop architecture to control its VCO through a reference clock and integer divider. Designers program the operating configuration through the serial interface, while lock detect provides a digital status indication that can be monitored by a host controller or used in system-level fault handling. Power-down modes reduce activity where the RF output is not required.
Typical uses include local oscillator generation for wireless receivers and transmitters, frequency conversion in RF communication equipment, test and measurement instruments, and clock or carrier generation for industrial and consumer systems. Its 2250 MHz VCO center frequency and divide-by-2 output make it particularly relevant to 2.4 GHz RF signal-chain designs.
Layout is critical because the VCO must remain stable while the synthesizer changes frequency. Follow the manufacturer reference layout, keep the VCO output path compact, place decoupling and loop-filter components close to their designated pins, and provide a continuous ground return through the exposed pad. Confirm lock, output power, spur performance, and supply sequencing during bring-up.
جایگزینهای drop-in برای ADF4360-1BCP — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای ADF4360-1BCP (همان فرمفاکتور و فوتپرینت).
ADF4360-2BCPZ
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
ADF4360-3BCPZ
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
ADF4360-4BCPZ
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
ADF4360-7BCPZ
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←ADF4360-8BCPZ
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
ADF4360-1BCP مشخصات
| VCO Center Frequency | 2250 MHz |
| Divide-by-2 RF Output Range | 1025 MHz to 1225 MHz |
| Maximum RF Output Frequency | 2450 MHz |
| Reference Input Frequency Range | 10 MHz to 250 MHz |
| Power Supply Voltage | 3.6 V |
| Logic Compatibility | 1.8 V |
| Synthesizer Architecture | Integer-N |
| Output Divider | Divide-by-2 |
| Programmable Output Power | Programmable |
| Programming Interface | 3-wire serial interface |
| Lock Detection | Digital |
| Power-Down Modes | Hardware and software |
| Integrated Functions | Integer-N synthesizer and voltage-controlled oscillator |
| تعداد پایه | 24 pins |
| بستهبندی | 24-lead LFCSP with exposed pad |
| نوع نصب | Surface mount |
راهنمای پیکربندی پین ADF4360-1BCP 24-lead lfcsp with exposed pad
پیکربندی پین برای ADF4360-1BCP (پکیج 24-lead lfcsp with exposed pad). شمارهگذاری پایهها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعملهای لحیمکاری به آن مراجعه کنید.
داده پینآوت تفصیلی موجود نیست برای ADF4360-1BCP.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
ADF4360-1BCP مناسب است برای 6 کاربردs: 2.4 GHz Wireless Transceiver, RF Receiver Local Oscillator, Frequency Conversion Subsystem, RF Test and Measurement Equipment, Industrial RF Control System, Wireless Sensor Gateway.
2.4 GHz Wireless Transceiver
The ADF4360-1BCP is suited to local-oscillator generation in 2.4 GHz wireless transmitters and receivers because Analog Devices identifies a 2250 MHz VCO center frequency and a maximum RF output frequency of 2450 MHz. Its integrated integer-N synthesizer allows the output frequency to be programmed through the three-wire serial interface. The programmable output power also provides an adjustment range for downstream RF stages. Designers should keep the VCO route short, follow the exposed-pad grounding pattern, and validate phase noise and spurious performance for the selected channel bandwidth.
پیشنهادی
RF Receiver Local Oscillator
A receiver can use the ADF4360-1BCP to generate the local oscillator required for downconversion. The 2250 MHz VCO center frequency aligns with RF designs around the 2.4 GHz region, while the divide-by-2 option provides a 1025 MHz to 1225 MHz output. Because the synthesizer and VCO are integrated, the board avoids a separate VCO and divider assembly. The receiving chain should be evaluated for phase-noise impact, lock time, reference spur levels, and unwanted coupling from digital control signals.
پیشنهادی
Frequency Conversion Subsystem
The ADF4360-1BCP can serve as the tunable oscillator in a frequency-conversion subsystem where an integer-N PLL drives a mixer or switching element. Its 2450 MHz maximum RF output supports designs near the upper portion of the 2.4 GHz band, and its programmable output power helps accommodate different downstream drive requirements. Integration reduces board area and assembly complexity. Performance validation should include supply rejection, VCO tuning linearity, lock-detect behavior, and isolation from high-level switching nodes.
پیشنهادی
RF Test and Measurement Equipment
Programmable test equipment can use the ADF4360-1BCP as a compact signal source for exercising receiver and transmitter paths. The serial programming interface supports automated frequency setup, while digital lock detection can be monitored by the test controller. Its 3.6 V supply and 1.8 V-compatible logic simplify integration with embedded test-control electronics. For accurate measurements, use a low-phase-noise reference, implement the manufacturer-recommended loop filter, and calibrate output power and frequency across the required operating range.
پیشنهادی
Industrial RF Control System
Industrial RF control systems can employ the ADF4360-1BCP when a compact, digitally controlled oscillator is needed for sensing, communications, or microwave-processing equipment. Programmable output power and hardware or software power-down modes support systems that must balance RF performance with energy use. The 24-lead exposed-pad package supports dense assemblies when the PCB provides adequate thermal relief. Designers should separate the sensitive VCO region from motors, relays, and switching power converters, then verify conducted and radiated emissions.
پیشنهادی
Wireless Sensor Gateway
A wireless sensor gateway can use the ADF4360-1BCP for RF modulation, clock generation, or local-oscillator functions within a compact 2.4 GHz system. The integrated integer-N architecture reduces the number of external frequency-generation components, while digital lock detect and power-down control fit managed embedded firmware. Low-power operation should be implemented with the documented power-down modes rather than by removing the reference signal during operation. Printed-circuit design should preserve the recommended ground via pattern and minimize VCO trace coupling.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای ADF4360-1BCP — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | ADF4360-2BCPZ | ADF4360-3BCPZ | ADF4360-4BCPZ | ADF4360-7BCPZ | ADF4360-8BCPZ |
|---|---|---|---|---|---|---|
| Package | 24-LFCSP exposed pad | 24-LFCSP exposed pad | 24-LFCSP exposed pad | 24-LFCSP exposed pad | 24-LFCSP exposed pad | 24-LFCSP exposed pad |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| VCO Center Frequency | 2250 MHz | Approximately 2000 MHz | Approximately 3000 MHz | Approximately 4000 MHz | Approximately 7000 MHz | Approximately 8000 MHz |
تفاوتهای کلیدی
- Direct alignment with the 2.4 GHz RF region (در مقابلADF4360-3BCPZ)
- Divide-by-2 output covers a separate lower-frequency range (در مقابلADF4360-8BCPZ)
- Compact integrated VCO and integer-N control (در مقابلADF4360-2BCPZ)
یادداشتهای طراحی
Follow the manufacturer reference layout and keep the VCO output route short. Place input, output, and loop-filter decoupling components at the pins designated by the application schematic. Maintain the specified ground-via pattern beneath the 24-lead LFCSP exposed pad and provide an uninterrupted ground reference around the VCO section. Changes to trace length or return-current paths can affect tuning stability and phase noise.
Use a clean 3.6 V supply and decouple it according to the manufacturer application circuit. Because the ADF4360-1 includes a sensitive VCO, supply ripple can appear as phase noise or reference spurs. Keep switching-regulator and digital-supply return currents away from the VCO ground path, and verify power-supply rejection during system-level testing. The 1.8 V-compatible interface reduces control-signal amplitude but does not remove the need for careful supply filtering.
Do not select an ADF4360 family member solely from its package. The ADF4360-2BCPZ through ADF4360-8BCPZ use the same family package but cover different VCO bands, so the selected output must remain inside the required tuning range. Recheck the integer-N divider values, reference ratio, loop filter, lock behavior, output power settings, and register map after any substitution. Confirm the exact ordering suffix and temperature grade before production release.
Treat the reference and RF paths as sensitive signals. Use short, impedance-controlled connections, avoid routing them beneath or parallel to high-energy switching nodes, and keep the programming bus away from the VCO output path. Monitor the digital lock-detect signal during startup and frequency changes. Validate spurious emissions, lock time, and phase noise with the final reference clock and PCB stack-up because enclosure and power-supply details can alter measured performance.
اطلاعات انطباق
Compliance attributes were not identified in the cited product information and must be confirmed against the current Analog Devices product documentation before procurement.