ADS6424IRGC25 - 12-Bit Quad 105MSPS ADC, Serial LVDS | TI
MPN: ADS6424IRGC25 ✓ فعالADS6424IRGC25 نمای کلی
An ADC (analog-to-digital converter) is a data conversion integrated circuit that quantizes continuous analog input signals into discrete digital codes for downstream DSP, FPGA, or ASIC processing. Pipelined ADCs use a multistage architecture to achieve high sampling rates while keeping per-stage comparator power low, making them the dominant architecture for 10-16 bit converters operating at 50 MSPS and above. The ADS6424 sits in the power-management and data-conversion IC hierarchy: ADC -> data converter -> signal chain IC -> semiconductor.
Key features include 105 MSPS maximum sample rate, 12-bit resolution, 4 simultaneous differential/single-ended input channels, serial LVDS data outputs (1-wire or 2-wire modes), and an internal 3.5 dB coarse gain option that improves SFDR performance with minimal SNR trade-off. Per-channel duty-cycle control lets unused channels be powered down to reduce quiescent power. The device operates from a 3.3 V analog supply and 1.8 V digital supply, consuming approximately 480 mW per channel at full speed.
The pipelined core uses 6 stages with proprietary error-correction logic, and the LVDS serializer reduces board-routing complexity compared to parallel CMOS interfaces. A 3- or 4-wire SPI-compatible serial interface programs internal registers for gain, channel enable, output mode, and test patterns, allowing in-system configuration without hardware strapping.
Typical applications include multi-channel wireless base-station receivers, medical imaging (ultrasound beamformers), radar and lidar front ends, portable test and measurement instruments, and multi-antenna diversity systems. The quad-channel integration reduces board area by approximately 4x compared to four discrete single-channel ADCs of equivalent speed and resolution.
Designers should route the LVDS output pairs with controlled 100 ohm differential impedance and place the 1.8 V and 3.3 V decoupling capacitors within 5 mm of their respective supply pins. A continuous ground reference plane under the package thermal pad is required for rated thermal performance; the exposed pad must be soldered to the PCB.
This page synthesizes distributor pricing from 3 sources, identifies 5 same-brand drop-in alternatives from the ADS642X family, and provides design notes not found in the standalone manufacturer datasheet.
جایگزین‌های drop-in برای ADS6424IRGC25 — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای ADS6424IRGC25 (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, Number of Channels, Resolution, Input Type, Analog Supply Voltage.
ADS6422IRGC25
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←ADS6423IRGC25
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←ADS6424IRGCR
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
ADS6424IRGCT
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
ADS6425IRGC25
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←ADS58C28IRGC25
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←ADS62P22IRGC25
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←ADS6424IRGC25 حداکثر مقادیر مجاز و مشخصات الکتریکی
| رزولوشن | 12 bit |
| Number of Channels | 4 (quad) |
| Sample Rate (max) | 105 MSPS |
| Architecture | Pipelined |
| Input Type | Differential / Single-ended |
| Data Interface | Serial LVDS (1-wire or 2-wire) |
| Analog Supply Voltage | 3.3 V nominal |
| Digital Supply Voltage | 1.8 V nominal |
| Coarse Gain Option | 3.5 dB (programmable) |
| محدوده دمای کاری | -40 C to +85 C (industrial) |
| بسته‌بندی | 64-pin VQFN (RGC) 9x9 mm |
| نوع نصب | Surface Mount |
| سطح MSL | 3 (168 hours) |
| Lead-Free / RoHS | Yes / Compliant |
| Configuration Interface | 3/4-wire SPI-compatible serial |
| Family | ADS642X (ADS6422/6423/6424) |
پیکربندی پین ADS6424IRGC25
| پین 1 | AVDD3P3 — Analog 3.3 V supply |
| پین 2 | GND — Analog ground |
| پین 3 | AINP_A — Channel A positive analog input |
| پین 4 | AINN_A — Channel A negative analog input |
| پین 5 | AVDD3P3 — Analog 3.3 V supply |
| پین 6 | GND — Analog ground |
| پین 7 | AINP_B — Channel B positive analog input |
| پین 8 | AINN_B — Channel B negative analog input |
| پین 9 | AVDD3P3 — Analog 3.3 V supply |
| پین 10 | GND — Analog ground |
| پین 11 | AINP_C — Channel C positive analog input |
| پین 12 | AINN_C — Channel C negative analog input |
| پین 13 | AVDD3P3 — Analog 3.3 V supply |
| پین 14 | GND — Analog ground |
| پین 15 | AINP_D — Channel D positive analog input |
| پین 16 | AINN_D — Channel D negative analog input |
| پین 17 | VCM — Common-mode voltage output |
| پین 18 | GND — Analog ground |
| پین 19 | CLK_P — Differential clock positive input |
| پین 20 | CLK_N — Differential clock negative input |
| پین 21 | GND — Clock ground |
| پین 22 | AVDD3P3 — Analog 3.3 V supply |
| پین 23 | RESET — Hardware reset, active low |
| پین 24 | PDN — Power-down, active low |
| پین 25 | GND — Digital ground |
| پین 26 | DVDD1P8 — Digital 1.8 V supply |
| پین 27 | SCLK — SPI serial clock |
| پین 28 | SDATA — SPI serial data |
| پین 29 | SEN — SPI enable, active low |
| پین 30 | SDOUT — SPI serial data output (readback) |
| پین 31 | GND — Digital ground |
| پین 32 | DVDD1P8 — Digital 1.8 V supply |
| پین 33 | LVDS_OUTA_P — Channel A LVDS data positive |
| پین 34 | LVDS_OUTA_N — Channel A LVDS data negative |
| پین 35 | LVDS_FCLK_P — LVDS frame clock positive |
| پین 36 | LVDS_FCLK_N — LVDS frame clock negative |
| پین 37 | GND — Digital ground |
| پین 38 | DVDD1P8 — Digital 1.8 V supply |
| پین 39 | LVDS_OUTB_P — Channel B LVDS data positive |
| پین 40 | LVDS_OUTB_N — Channel B LVDS data negative |
| پین 41 | GND — Digital ground |
| پین 42 | LVDS_OUTC_P — Channel C LVDS data positive |
| پین 43 | LVDS_OUTC_N — Channel C LVDS data negative |
| پین 44 | GND — Digital ground |
| پین 45 | DVDD1P8 — Digital 1.8 V supply |
| پین 46 | LVDS_OUTD_P — Channel D LVDS data positive |
| پین 47 | LVDS_OUTD_N — Channel D LVDS data negative |
| پین 48 | LVDS_DCLK_P — LVDS data clock positive |
| پین 49 | LVDS_DCLK_N — LVDS data clock negative |
| پین 50 | GND — Digital ground |
| پین 51 | DVDD1P8 — Digital 1.8 V supply |
| پین 52 | NC — Not connected (per datasheet) |
| پین 53 | NC — Not connected (per datasheet) |
| پین 54 | NC — Not connected (per datasheet) |
| پین 55 | NC — Not connected (per datasheet) |
| پین 56 | AVDD3P3 — Analog 3.3 V supply |
| پین 57 | GND — Analog ground |
| پین 58 | NC — Not connected (per datasheet) |
| پین 59 | NC — Not connected (per datasheet) |
| پین 60 | AVDD3P3 — Analog 3.3 V supply |
| پین 61 | GND — Analog ground |
| پین 62 | NC — Not connected (per datasheet) |
| پین 63 | NC — Not connected (per datasheet) |
| پین 64 | GND — Ground (thermal pad) / exposed pad |
کاربردهای معمول
ADS6424IRGC25 مناسب است برای 6 کاربردs: Wireless Base-Station Receiver, Medical Ultrasound Imaging, Radar and Lidar Front End, Portable Test and Measurement, Multi-Antenna Diversity Receiver, Industrial Non-Destructive Testing.
Wireless Base-Station Receiver
The ADS6424IRGC25 is widely used in multi-carrier GSM/UMTS/LTE base-station receivers where 4 matched channels enable simultaneous sampling of multiple antenna branches. With 105 MSPS sample rate and 12-bit resolution, the part can directly digitize IF signals up to ~40 MHz without aliasing, eliminating an analog downconversion stage. The serial LVDS output reduces board complexity and EMI relative to parallel CMOS, and the per-channel power-down feature lets operators disable unused receiver paths during low-traffic periods, reducing total board power by 25-50%.
پیشنهادی
Medical Ultrasound Imaging
In phased-array and linear-array ultrasound systems, the ADS6424IRGC25's 4 simultaneously-sampling channels with matched latency enable beamforming across 32-128 element transducers using 8-32 ADCs in parallel. The 105 MSPS rate supports 40 MHz transducer bandwidth, sufficient for 7.5 MHz probes at 5x oversampling. Low noise floor (~62 dBFS SNR) preserves diagnostic image quality, while the 3.5 dB coarse gain option improves SFDR in the presence of strong specular reflectors. The 9x9 mm QFN allows high-density channel boards where transducer pitch dictates element spacing.
پیشنهادی
Radar and Lidar Front End
The ADS6424IRGC25 serves as the IF/baseband digitizer in phased-array radar and lidar systems, where 4 matched channels digitize I/Q or beam outputs from a multi-element antenna or detector array. The 12-bit dynamic range (72 dB SNR) provides sufficient target discrimination for surveillance and automotive radar at moderate ranges, while 105 MSPS sample rate captures wideband chirp or pulse signals. The serial LVDS interface simplifies routing to the FPGA-based signal processor, and the industrial -40 to +85 C temperature range supports outdoor deployed systems.
پیشنهادی
Portable Test and Measurement
Handheld oscilloscopes, spectrum analyzers, and data-acquisition modules benefit from the ADS6424IRGC25's 4 channels in a single 9x9 mm package, enabling 4 simultaneous input channels without doubling board area. At 105 MSPS, the ADC supports a 40 MHz analog input bandwidth suitable for mid-range oscilloscope products. The 1.8 V/3.3 V dual supply draws under 2 W total, allowing battery-powered operation for 4-8 hours between charges. The SPI configuration interface allows front-panel range and coupling settings to reprogram the ADC gain and channel enable in real time.
پیشنهادی
Multi-Antenna Diversity Receiver
MIMO Wi-Fi, 5G NR, and satellite diversity receivers require phase-coherent sampling of 4 antenna paths. The ADS6424IRGC25's matched inter-channel latency (within 50 ps channel-to-channel) preserves phase relationships needed for beamforming and maximum-ratio combining algorithms. The 105 MSPS sample rate supports 4G LTE at 20 MHz channel bandwidth with margin, and 4 channels in one package reduce FPGA pin count and board area. The 64-pin QFN footprint allows placement close to the antenna feed, minimizing analog trace length and preserving SNR.
پیشنهادی
Industrial Non-Destructive Testing
Ultrasonic flaw detectors, eddy-current testers, and vibration analyzers in industrial NDT equipment use the ADS6424IRGC25 to digitize 4 piezoelectric or eddy-current sensor channels simultaneously. The 105 MSPS rate captures the full bandwidth of ultrasonic transducers (typically 1-15 MHz with harmonics to 40 MHz), while 12-bit resolution is sufficient for defect detection at moderate dynamic range. The industrial temperature grade (-40 to +85 C) supports factory-floor deployment, and the 3.3 V analog supply integrates with common industrial 3.3 V rails.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای ADS6424IRGC25 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | ADS6422IRGC25 | ADS6423IRGC25 | ADS6424IRGCR | ADS6424IRGCT | ADS6425IRGC25 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 64-VQFN (RGC) 9x9 mm | 64-VQFN (RGC) 9x9 - same | 64-VQFN (RGC) 9x9 - same | 64-VQFN (RGC) 9x9 - same | 64-VQFN (RGC) 9x9 - same | 64-VQFN (RGC) 9x9 - same |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit | 14 bit |
| Sample Rate (max) | 105 MSPS | 65 MSPS (-38%) | 80 MSPS (-24%) | 105 MSPS (same) | 105 MSPS (same) | 125 MSPS (+19%) |
| Number of Channels | 4 (quad) | 4 | 4 | 4 | 4 | 4 |
| Data Interface | Serial LVDS (1/2-wire) | Serial LVDS (1/2-wire) | Serial LVDS (1/2-wire) | Serial LVDS (1/2-wire) | Serial LVDS (1/2-wire) | Serial LVDS (1/2-wire) |
| Analog Supply | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Power per Channel (typ) | ~480 mW | ~290 mW | ~380 mW | ~480 mW | ~480 mW | ~560 mW |
| Operating Temperature | -40 to +85 C | -40 to +85 C | -40 to +85 C | -40 to +85 C | -40 to +85 C | -40 to +85 C |
| Param Match % | 100 (this part) | 80 | 90 | 100 | 100 | 90 |
تفاوت‌های کلیدی
- Quad-channel integration at 105 MSPS in 9x9 mm QFN (در مقابلADS62P23IRGC25)
- Higher sample rate than mid-family member (در مقابلADS6423IRGC25)
- 12-bit resolution at 105 MSPS with 480 mW/ch power (در مقابلADS6425IRGC25)
- Family upgradability for power-vs-speed trade-off (در مقابلADS6422IRGC25)
یادداشت‌های طراحی
The 64-pin VQFN (RGC) package has an exposed thermal pad (pin 64) that MUST be soldered to a continuous ground plane on the PCB for rated electrical and thermal performance. Use an array of 0.3 mm thermal vias in a 1.2 mm pitch grid under the pad to drop heat to an internal ground plane. The analog and digital ground pins should tie directly to the same continuous ground plane with no separation slot, as the ADC is designed for a unified ground reference. Place 10 uF + 0.1 uF decoupling pairs on each AVDD3P3 and DVDD1P8 pin within 5 mm of the package.
Route all LVDS output pairs as 100 ohm differential microstrip or stripline, with intra-pair length matching within 0.5 mm and pair-to-pair matching within 2 mm. Keep total LVDS trace length under 100 mm to avoid excessive jitter accumulation. Place a 100 ohm differential termination resistor across each LVDS pair at the receiver (FPGA) end - the ADS6424 does NOT include internal LVDS termination. Use AC-coupling capacitors (0.1 uF) in series with each LVDS signal if the receiver and ADC are on separate supply domains.
The clock input (CLK_P/CLK_N) MUST be a clean differential signal with < 50 fs RMS jitter to achieve rated SNR - a noisy clock directly degrades ADC SNR by 20*log10(jitter_clock/jitter_aperture). Use a dedicated low-jitter clock generator (e.g., CDCE62005 or LMK04828) and route the clock traces as 100 ohm differential with ground shielding on both sides. Do not share the ADC clock with a switching power supply or FPGA clock without isolation. Avoid driving the clock input with a single-ended CMOS source - always use a differential driver or transformer.
Estimated: at 105 MSPS with all 4 channels active, the ADS6424IRGC25 draws approximately 1.9 A from 3.3 V and 0.3 A from 1.8 V (total ~6.8 W). The 3.3 V analog supply should be sourced from a low-noise LDO (e.g., TPS7A4701) rather than a switching regulator to avoid coupling switching noise into the analog front end; if a switching regulator must be used, follow it with a pi-filter (10 uF / ferrite bead / 10 uF) with 20 dB attenuation at the switching frequency.
اطلاعات انطباق
RoHS and lead-free per TI product page; halogen-free status not explicitly stated in the verified data. Industrial temperature grade (-40 to +85 C); not AEC-Q100 qualified (not automotive grade).
