CD4503BD3 Hex 3-State Buffer | Harris Corporation | Logic IC
MPN: CD4503BD3 ✗ پایان تولیدCD4503BD3 نمای کلی
A three-state buffer is a digital logic device that can actively drive a high level, actively drive a low level, or enter a high-impedance state. This tri-state behavior allows multiple devices to share a common data bus without creating contention when more than one output is enabled. Within the device hierarchy, the CD4503 belongs to the logic IC family and supports bidirectional data routing, signal isolation, and bus arbitration.
The CD4503 family is designed for systems that require buffered, non-inverting logic signals and controlled output enable functions. Its six-buffer arrangement allows multiple lines to be managed efficiently, while the separate disable controls provide flexibility for grouping four buffers and two buffers independently. The 16-CERDIP package is suitable for applications using through-hole mounting and industrial or legacy control equipment.
The CD4503BD3 is specified as a single-element, six-bit-per-element output device in distributor catalog data. Its CMOS construction supports low-power logic operation, while the high sink and source current capability helps the device drive connected bus loads and downstream CMOS stages more effectively than a basic unbuffered gate arrangement.
Typical uses include data-bus isolation, control-signal buffering, multibus interface logic, address or data-line multiplexing, and industrial automation equipment. The independent disable controls allow designers to place selected portions of the bus in a high-impedance state during transfers, testing, or shared-bus arbitration.
When assigning PCB connections, use the pin-description table in the manufacturer datasheet and preserve the 16-CERDIP pin numbering. Check enable and disable polarity, unused-input states, and the required input levels before finalizing the logic design. Account for signal propagation delay and bus timing when the device is used in high-speed clocked systems.
This page consolidates the CD4503BD3 catalog identity, package information, engineering use cases, and drop-in replacement guidance to support component selection and PCB-level planning without duplicating the complete manufacturer pinout table.
جایگزینهای drop-in برای CD4503BD3 — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای CD4503BD3 (همان فرمفاکتور و فوتپرینت) — متفاوت در Package.
CD4503BD
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
CD4503BE
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←CD4503BE
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←CD4503BE
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←CD4503BE
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←CD4503BD3 حداکثر مقادیر مجاز و مشخصات الکتریکی
| Product Type | Hex non-inverting three-state buffer |
| Logic Family | CMOS |
| Number of Buffer Elements | 6 |
| Bits per Element | 6 |
| پیکربندی خروجی | Non-inverting |
| Output States | High, low, and high impedance |
| Number of Disable Controls | 2 |
| بستهبندی | 16-CERDIP |
| نوع نصب | Through-hole |
| Output Drive Capability | High sink and source current capability |
راهنمای پیکربندی پین CD4503BD3 16-cerdip
پیکربندی پین برای CD4503BD3 (پکیج 16-cerdip). این IC دیجیتال شامل GPIO، رابطهای ارتباطی (UART، SPI، I2C) و پینهای تغذیه است. برای عملکردهای جایگزین پین و گزینههای پیکربندی به دیتاشیت سازنده مراجعه کنید. ضروری برای طراحی سیستمهای نهفته و چیدمان PCB.
داده پینآوت تفصیلی موجود نیست برای CD4503BD3.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
CD4503BD3 مناسب است برای 6 کاربردs: Shared Data Bus Isolation, Industrial Control Signal Buffering, Address and Data Multiplexing, Data Bus Arbitration, Instrumentation Signal Isolation, Legacy Peripheral Interface.
Shared Data Bus Isolation
The CD4503BD3 fits shared-bus interfaces where six non-inverting signals must connect to a common data path only when individually permitted. Its three-state outputs let selected drivers release the bus into a high-impedance condition, while the two disable controls provide grouped control of four channels and two channels. This arrangement reduces the number of discrete enable signals required in control logic. Before routing the board, confirm disable polarity and propagation timing against the bus protocol, and ensure that enabled outputs never contend on the same net.
پیشنهادی
Industrial Control Signal Buffering
The CD4503BD3 is suitable for industrial control boards that need buffered non-inverting logic between a controller and field-facing circuitry. Six channels provide parallel signal conditioning, while the grouped disable controls can isolate groups of outputs during a transition or test state. The high sink and source current capability supports CMOS-compatible downstream loads. Because the device is specified in a 16-CERDIP package, it is most practical for through-hole legacy or industrial systems; confirm voltage limits, temperature range, and output-drive values from the manufacturer datasheet before layout release.
پیشنهادی
Address and Data Multiplexing
The CD4503BD3 can support address-and-data multiplexing because it contains six non-inverting buffers and two independently grouped disable controls. One group of four channels and another group of two channels can be selected according to the multiplexing sequence, allowing the external bus to present different information phases. The principal design constraint is timing: disable propagation delay must be compatible with setup and hold requirements at the receiving device. Use the datasheet timing characteristics and define unused-input states explicitly.
پیشنهادی
Data Bus Arbitration
The CD4503BD3 can participate in a bus-arbitration scheme by placing individual output groups in a high-impedance state when another source must drive the bus. Grouped disable control offers a practical balance between bus granularity and control complexity for six parallel lines. The design must prevent overlap between enabled and disabled drivers, so arbitration timing must include the buffer’s propagation delay and any external gate delay. Verify the high-impedance transition behavior and supply levels against the manufacturer datasheet before integrating it with a bidirectional bus controller.
پیشنهادی
Instrumentation Signal Isolation
The CD4503BD3 can isolate groups of instrumentation or test-control lines by enabling and disabling buffered outputs in coordinated sequences. This is useful when a peripheral bus must remain electrically quiet during measurement, calibration, or maintenance states. The non-inverting arrangement preserves logic polarity, and the high sink and source current capability is useful for driving standard CMOS inputs. Validate input leakage, output impedance, and switching behavior against the actual bus timing and loading conditions, especially where long PCB traces or cable-connected loads are involved.
پیشنهادی
Legacy Peripheral Interface
The CD4503BD3 is appropriate for legacy peripheral-interface boards that require a 16-pin through-hole CMOS buffer and selectable high-impedance outputs. It can buffer six non-inverting control or data lines while allowing a bus section to disconnect during a transfer. The ceramic DIP footprint supports repair and retrofit workflows common in older industrial equipment. Before substituting it into an operating system, verify that supply voltage, input thresholds, output drive, propagation delay, and disable polarity match the original device’s operating requirements.
پیشنهادی
دادههای مرجع مهندسی برای CD4503BD3 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول |
|---|---|
| Brand | Harris Corporation |
| Package | 16-CERDIP |
| Product Type | Hex non-inverting three-state buffer |
| Number of Buffer Elements | 6 |
| Bits per Element | 6 |
| Disable Controls | 2; one controls four buffers and one controls two buffers |
| Output States | High, low, and high impedance |
| Logic Technology | CMOS |
| Mounting Type | Through-hole |
| Output Drive | High sink and source current capability |
تفاوتهای کلیدی
- Six non-inverting channels with grouped tri-state control (در مقابلConventional single-channel non-inverting buffer)
- Two disable controls cover different channel groups (در مقابلBuffer with one shared enable input)
- High sink and source current capability (در مقابلBasic CMOS gate output)
یادداشتهای طراحی
Never enable two CD4503BD3 outputs onto the same net unless both devices are designed for a documented bus-ownership transition. Inspect disable-control polarity in the CD4503 manufacturer datasheet and include propagation delay in the arbitration timing budget. Holding every input at a defined logic level also prevents unused channels from entering an indeterminate state.
Use the 16-CERDIP pin-description table to assign every connection and preserve standard counter-clockwise numbering. Keep disable traces away from clocks and sensitive data nets, and route each output to either a dedicated receiver or a properly controlled shared bus. Do not rely on a board outline alone as proof of electrical compatibility.
Before energizing the circuit, verify the supply-voltage range, absolute maximum ratings, and input thresholds from the CD4503 manufacturer datasheet. Confirm that the board’s pull-up or pull-down network cannot force an output beyond its permitted range while the CD4503BD3 is in the high-impedance state. Add decoupling according to the device’s recommended operating conditions and power-supply layout practice.
اطلاعات انطباق
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified for CD4503BD3. Confirm compliance and traceability with the manufacturer or the organization handling the purchase.