Texas Instruments

DS90CF384AMTDX - 24-Bit 3.3V LVDS Receiver | Texas Instruments

MPN: DS90CF384AMTDX ✓ فعال
+3.3 V Vdss 56-pin TSSOP (DGG) Package 65 MHz Speed
حداقل سفارش: 1 |

DS90CF384AMTDX نمای کلی

The Texas Instruments DS90CF384AMTDX is a +3.3 V LVDS receiver for 24-bit flat panel display links operating at 65 MHz, packaged in a 56-pin TSSOP. It is designed for display-interface systems that require reception of serialized low-voltage differential signaling data. The device is associated with an 1800 Mbps data-rate description in the product listing, making it suitable for high-speed display link interfaces where signal integrity and receiver performance are important.

An LVDS receiver is an interface circuit that converts differential data signals into logic-level signals for the receiving system. LVDS, or low-voltage differential signaling, belongs to the interface IC category and supports high-speed data transfer over balanced interconnects. The DS90CF384AMTDX is used in display applications where a transmitter sends serialized pixel or control data over a differential link and the receiver restores usable digital data for downstream logic.

Key features of the device include its +3.3 V supply operation, 24-bit flat panel display link support, 65 MHz operating frequency and 56-pin TSSOP package. The 56-pin package provides the physical interface for the receiver's digital, differential and power connections. The listed operating temperature range is -10 °C to +70 °C, making the device suitable for commercial and industrial equipment where that temperature range is acceptable.

The DS90CF384AMTDX is specifically identified as an LVDS interface IC for 24-bit flat panel display links. In a typical link, the receiver accepts low-voltage differential data from a display transmitter, applies receiver functions designed for the LVDS interface, and presents recovered data to the display or video processing circuitry. Designers should pay close attention to trace geometry, connector and cable topology, supply decoupling and the timing relationship between the transmitter and receiver.

Typical uses include flat panel display controllers, monitor and television interface boards, industrial display equipment, test systems for display links and embedded display subsystems. The receiver can be considered when the system already uses an LVDS display link and requires a 24-bit, 65 MHz class receiver in a 56-pin TSSOP footprint.

A key design consideration is the use of controlled-impedance differential routing and a properly engineered connector or cable path. Keep the receiver supply and ground connections close to the device, follow the manufacturer's recommended decoupling arrangement and validate the complete transmitter-to-receiver channel for eye margin, jitter and common-mode behavior. The DS90CF384AMTDX should be selected only when its 3.3 V supply, 24-bit link, 65 MHz frequency and TSSOP package requirements match the existing system.

This product page combines manufacturer identification, interface parameters, package information, sourcing guidance and practical considerations for evaluating the DS90CF384AMTDX in a flat panel display receiver design.

جایگزین‌های drop-in برای DS90CF384AMTDX — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

DS90CF384AMTD/NOPB

✅ جایگزین مستقیم
📦 56-pin TSSOP (DGG)
The /NOPB suffix identifies the lead-free ordering designation; both devices are listed as 24-bit, +3.3 V, 65 MHz LVDS FPD Link receivers in the same 56-pin TSSOP package.

📋 جایگزین مرجع (خارج از کاتالوگ)

DS90CF384AMTDX/NOPB

✅ جایگزین مستقیم
📦 56-pin TSSOP (DGG)
The /NOPB suffix identifies the lead-free ordering designation; both devices are listed as 24-bit, +3.3 V, 65 MHz LVDS FPD Link receivers in the same 56-pin TSSOP package.

📋 جایگزین مرجع (خارج از کاتالوگ)

DS90CF384AMTDX مشخصات

Device Type +3.3 V LVDS Receiver
Display Link Data Width 24 bit
Operating Frequency 65 MHz
نرخ داده 1800 Mbps
ولتاژ تغذیه +3.3 V
نوع رابط Low-Voltage Differential Signaling (LVDS)
Application Flat Panel Display Link
بسته‌بندی 56-pin TSSOP (DGG)
تعداد پایه 56 pins
محدوده دمای کاری -10 °C to +70 °C
نوع نصب Surface Mount
Manufacturer Texas Instruments

راهنمای پیکربندی پین DS90CF384AMTDX 56-pin tssop (dgg)

پیکربندی پین برای DS90CF384AMTDX (پکیج 56-pin tssop (dgg)). شماره‌گذاری پایه‌ها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعمل‌های لحیم‌کاری به آن مراجعه کنید.

نمودار پین‌آوت پکیج 56-pin tssop (dgg) برای DS90CF384AMTDX

داده پین‌آوت تفصیلی موجود نیست برای DS90CF384AMTDX.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

DS90CF384AMTDX مناسب است برای 6 کاربردs: Flat Panel Monitor Receiver, Industrial Display Controller, Display Test Equipment, Video Processing Interface, Embedded Display System, Broadcast and Studio Display Interface.

📺

Flat Panel Monitor Receiver

The DS90CF384AMTDX fits a flat panel monitor receiver stage when the display link uses a compatible 24-bit LVDS protocol at 65 MHz. It receives serialized differential display data and provides the interface toward the downstream display-processing circuitry. The +3.3 V supply aligns with many modern display-controller power domains, while the 56-pin TSSOP supports a conventional surface-mount layout. The design should preserve controlled-impedance differential routing, provide local supply decoupling and verify connector or cable losses before operation. Because the listed temperature range is -10 °C to +70 °C, enclosure temperature must be checked against that limit.

🏭

Industrial Display Controller

The DS90CF384AMTDX can be used in an industrial display controller when the equipment remains within its published -10 °C to +70 °C operating range. Its 24-bit FPD Link capability and 65 MHz operating frequency are suitable for a receiver-side link to a compatible panel interface. The +3.3 V supply simplifies integration with low-voltage display logic, but the system designer must still provide a clean 3.3 V rail and careful LVDS routing. Industrial enclosure temperature, grounding and cable length should be evaluated together because the receiver specification does not by itself guarantee performance for every cable or connector implementation.

🧪

Display Test Equipment

The DS90CF384AMTDX is suitable for a display-link test fixture or receiver card that reproduces a 24-bit LVDS FPD interface at 65 MHz. Its receiver function can be paired with a compatible transmitter, pattern generator or display test platform to exercise cables, connectors and downstream video logic. The 56-pin TSSOP package allows the receiver to be placed close to the input connector, which helps minimize routing sensitivity. Design the fixture with controlled-impedance differential pairs and observe differential voltage and timing at the receiver. Keep the card temperature within -10 °C to +70 °C and confirm the exact protocol before using the fixture as a production test path.

🖥️

Video Processing Interface

The DS90CF384AMTDX can serve as the display-side receiver in a video processing subsystem that communicates with a compatible LVDS transmitter over a 24-bit FPD Link. The 65 MHz receiver class and listed 1800 Mbps data rate align with high-speed serialized display links, while the +3.3 V operating supply simplifies interface with digital logic. Placement near the display connector helps keep the differential pair short and reduces sensitivity to routing discontinuities. The processing board still needs independent power sequencing and grounding, and the receiver's -10 °C to +70 °C range must be respected in the final equipment.

🔧

Embedded Display System

The DS90CF384AMTDX is appropriate for an embedded display subsystem that receives serialized panel data over a compatible 24-bit LVDS FPD Link at 65 MHz. Its small 56-pin TSSOP footprint supports compact controller boards, and the +3.3 V supply is convenient for embedded logic that already operates at 3.3 V. Integration requires a matched transmitter, correctly terminated differential inputs and PCB routing based on the manufacturer's interface recommendations. Because no public complete pin list is reproduced here, use the pin-description table in the Texas Instruments datasheet for board construction. Check the final enclosure temperature against the -10 °C to +70 °C operating range.

📡

Broadcast and Studio Display Interface

The DS90CF384AMTDX may be used in a broadcast or studio display interface when the source equipment implements a compatible 24-bit LVDS FPD Link at 65 MHz. The device provides the receiver function required at the panel end of the link, while its +3.3 V supply and surface-mount TSSOP package support compact interface cards. Signal-integrity quality depends on the complete transmitter, cable, connector and receiver path, so validate eye margin and jitter in the assembled system. The device's listed -10 °C to +70 °C operating range also requires consideration in studio equipment where internal temperature may exceed the surrounding room temperature.

خلاصه محصولات پیشنهادی

DS90CF384AMTD/NOPB Same-family 24-bit 65 MHz LVDS receiver candidate استفاده‌شده در: Flat Panel Monitor Receiver, Industrial Display Controller, Display Test Equipment, Video Processing Interface, Embedded Display System, Broadcast and Studio Display Interface DS90CF384AMTDX/NOPB Lead-free ordering variant of the same receiver استفاده‌شده در: Flat Panel Monitor Receiver, Industrial Display Controller, Display Test Equipment, Video Processing Interface, Embedded Display System, Broadcast and Studio Display Interface
What is the DS90CF384AMTDX?
The DS90CF384AMTDX is a Texas Instruments +3.3 V LVDS receiver designed for 24-bit flat panel display links operating at 65 MHz. It is packaged in a 56-pin TSSOP (DGG). The device belongs to the display-interface receiver category and is intended for systems that transmit serialized display data over a low-voltage differential signaling link.
What is the operating voltage of DS90CF384AMTDX?
The DS90CF384AMTDX operates from a +3.3 V supply. According to the Texas Instruments DS90CF384 product description, the device is a +3.3 V LVDS receiver, making it appropriate for display interface circuits that use a 3.3 V power domain. The verified product information does not specify a wider allowable supply-voltage range.
How many display data bits does DS90CF384AMTDX support?
The DS90CF384AMTDX supports a 24-bit flat panel display link. According to the Texas Instruments product description, it is a 24-bit FPD Link receiver. This distinguishes it from related display-interface devices intended for a different data width, so the transmitter and receiver must be checked for matching link format before replacement.
What is the maximum operating frequency of DS90CF384AMTDX?
The DS90CF384AMTDX is identified as a 65 MHz LVDS flat panel display link receiver. The Arrow product listing also describes the device as an LVDS receiver with an 1800 Mbps data rate, which is consistent with the 65 MHz class of link operation. Confirm the exact timing budget and channel requirements against the manufacturer datasheet before finalizing a display timing design.
Where can I download the DS90CF384AMTDX datasheet?
The official DS90CF384 datasheet and product information are available from the Texas Instruments product page at https://www.ti.com/product/DS90CF384. The page is the preferred source for the device description, ordering information, quality information and manufacturer documentation. Use the DS90CF384AMTDX ordering entry linked from that page when confirming the exact 56-pin TSSOP variant.
Where can I find the DS90CF384AMTDX pinout?
The DS90CF384AMTDX pin assignment should be taken from the pin-description table in the Texas Instruments DS90CF384 datasheet. The verified ordering information identifies the device as a 56-pin TSSOP in the DGG package. No complete pin list is reproduced on this page, so use the manufacturer datasheet when assigning PCB nets and checking differential inputs, supply rails and outputs.
Can DS90CF384AMTDX be used for a flat panel monitor?
The DS90CF384AMTDX is suitable for a flat panel monitor or display-controller board when the system uses a compatible 24-bit LVDS FPD link at 65 MHz and uses a +3.3 V supply. The receiver must match the transmitter's electrical and timing requirements, while the PCB must provide controlled-impedance differential routing and suitable LVDS connector or cable geometry.
What is the difference between DS90CF384AMTDX and DS90CF384AMTD/NOPB?
The verified product information identifies both DS90CF384AMTDX and DS90CF384AMTD/NOPB as Texas Instruments 24-bit +3.3 V LVDS FPD Link receivers in 56-pin TSSOP packaging. The suffix /NOPB identifies the lead-free ordering designation. Use the manufacturer part details to confirm the exact temperature, packaging and marking attributes before treating the two orderable names as interchangeable.
Can DS90CF384AMTD/NOPB replace DS90CF384AMTDX?
DS90CF384AMTD/NOPB is the closest listed replacement candidate because both are identified as 24-bit, +3.3 V, 65 MHz LVDS FPD Link receivers in 56-pin TSSOP packages. Before substituting it, verify the exact pin assignments, temperature grade, ordering suffix and supply requirements in the Texas Instruments datasheet. The cross-reference listing supports the functional match but does not replace manufacturer qualification checks.
What can replace DS90CF384AMTDX?
DS90CF384AMTD/NOPB is a drop-in replacement candidate for DS90CF384AMTDX because the cross-reference information identifies it as the same 24-bit, +3.3 V LVDS receiver family in the same 56-pin TSSOP package. Validate the exact suffix, pinout and operating-temperature details before production use. No additional same-footprint cross-brand equivalent was established by the available manufacturer and cross-reference information.
Is DS90CF384AMTDX suitable for industrial display equipment?
The DS90CF384AMTDX can be evaluated for industrial display equipment when the ambient and internal temperatures remain within its listed -10 °C to +70 °C range. It provides the required 24-bit, 65 MHz LVDS receiver function for compatible display links. Environmental qualification beyond this published temperature range, including any specific industrial or automotive qualification, requires additional manufacturer confirmation.
Where can I buy DS90CF384AMTDX online?
Use the Request a Quote form on this page to request DS90CF384AMTDX availability, packaging details and current sourcing terms. The product is listed in a 56-pin TSSOP package and is identified by Texas Instruments as an active catalog device. The quote form is the appropriate route for confirming exact stock, date code, minimum order quantity and lead time for the required suffix.
What is the price of DS90CF384AMTDX?
The current DS90CF384AMTDX price is obtained through the Request a Quote form on this page. The available listing information identifies the exact MPN and its 56-pin TSSOP configuration, but it does not provide a qualifying quantity-break price table for this exact ordering code. Submit the required quantity and packaging details to receive current pricing and availability confirmation.
What is the lead time for DS90CF384AMTDX?
Request the current DS90CF384AMTDX lead time through the Request a Quote form on this page. Lead time can vary with the exact suffix, order quantity, packaging method, date code and current channel availability. The product listing confirms that DS90CF384AMTDX is a Texas Instruments TSSOP-56 interface IC, but it does not state a fixed production or shipment interval.
Is DS90CF384AMTDX in stock?
Use the Request a Quote form on this page to check current DS90CF384AMTDX stock and allocation. The verified listings show the part as an established catalog item with a 56-pin TSSOP package, while distributor snippets may not reflect current warehouse quantity. The quote request should include the required quantity, date-code preference and production schedule.
What are the key specifications of DS90CF384AMTDX that engineers should know?
The key DS90CF384AMTDX specifications are +3.3 V supply operation, a 24-bit flat panel display link, 65 MHz operating frequency, an 1800 Mbps listed data rate and a 56-pin TSSOP (DGG) package. The device is a Texas Instruments LVDS receiver with an operating-temperature range of -10 °C to +70 °C. These parameters determine transmitter matching, PCB routing, power design and environmental suitability.

داده‌های مرجع مهندسی برای DS90CF384AMTDX — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose DS90CF384AMTDX for a display receiver design that specifies a +3.3 V, 24-bit LVDS FPD Link operating at 65 MHz in a 56-pin TSSOP footprint. DS90CF384AMTD/NOPB is the closest listed substitution when the procurement configuration requires the /NOPB lead-free designation; verify the exact ordering suffix and temperature details before releasing the design. DS90CF384AMTDX/NOPB is another directly listed naming option with the same family and package information. The available cross-reference information did not establish a cross-brand, same-pinout drop-in receiver, so no unrelated LVDS receiver should be substituted solely because its link speed appears similar. Confirm protocol timing, pin assignments, supply requirements, channel signal integrity and the -10 °C to +70 °C operating range in the manufacturer documentation before production use.

مقایسه با جایگزین‌ها

پارامتر این محصول DS90CF384AMTD/NOPB DS90CF384AMTDX/NOPB
Package 56-pin TSSOP (DGG) 56-pin TSSOP (DGG) 56-pin TSSOP (DGG)
Brand Texas Instruments Texas Instruments Texas Instruments
Device Type +3.3 V LVDS Receiver +3.3 V LVDS Receiver +3.3 V LVDS Receiver
Display Link Data Width 24 bit 24 bit 24 bit
Operating Frequency 65 MHz 65 MHz 65 MHz
Supply Voltage +3.3 V +3.3 V +3.3 V
Lead-Free Ordering Designation Target ordering code does not include /NOPB /NOPB included /NOPB included

تفاوت‌های کلیدی

  • Matches the required 24-bit 65 MHz LVDS display-link role (در مقابلDS90CF384AMTD/NOPB)
  • Provides an exact lead-free ordering option (در مقابلDS90CF384AMTDX/NOPB)
  • Suited to compact display-interface boards (در مقابلDS90CF384AMTD/NOPB)

یادداشت‌های طراحی

Route the LVDS differential pair as a controlled-impedance, tightly coupled pair from the receiver to the connector or cable interface. Avoid stubs, test pads and right-angle discontinuities where possible, and use the manufacturer's pin-description table and layout guidance when assigning the differential inputs. Keep unrelated noisy switching nodes away from the receiver because the device is intended for high-speed differential display signaling.

Do not treat DS90CF384AMTDX, DS90CF384AMTD/NOPB and DS90CF384AMTDX/NOPB as interchangeable without checking the exact ordering suffix, marking and temperature information. The verified listings associate all three names with the same receiver family and 56-pin TSSOP package, but suffix handling can affect procurement labeling. Use the manufacturer part details and datasheet as the final authority for pin, grade and qualification decisions.

Provide a stable +3.3 V supply and place the required local decoupling close to the device power and ground pins. Keep return-current paths short and use a quiet ground reference for the interface circuitry. Decoupling values and placement should follow the manufacturer recommendations because no complete external-capacitor schedule was established by the verified product snippets.

Validate the complete transmitter-to-receiver path rather than evaluating only the receiver IC. Check differential input amplitude, common-mode voltage, eye margin and jitter with the intended connector and cable. The device is identified as a 65 MHz, 24-bit LVDS FPD Link receiver, but practical link performance also depends on source-device output, board geometry, cable length and termination strategy.

Confirm that the assembled board and enclosure remain within the listed -10 °C to +70 °C operating range. The TSSOP package provides a compact surface-mount footprint, but the available information does not establish a specific junction-temperature rating or thermal resistance. Use conservative ambient limits and manufacturer thermal information during final reliability analysis rather than inferring a thermal figure from the package name.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The verified product information does not state the compliance status of the exact DS90CF384AMTDX ordering code. The /NOPB suffix on listed alternates identifies a lead-free ordering designation, but it is not used here as proof of every compliance category.

جستجوهای مرتبط

ds90cf384amtdx nopb DS90CF384AMTDX datasheet DS90CF384AMTDX datasheet pdf DS90CF384AMTDX pinout DS90CF384AMTDX specifications DS90CF384AMTDX equivalent DS90CF384AMTDX replacement DS90CF384AMTDX price DS90CF384AMTDX stock Texas Instruments DS90CF384AMTDX DS90CF384AMTDX vs DS90CF384AMTD/NOPB DS90CF384 56 pin TSSOP receiver 24-bit 65 MHz LVDS receiver DS90CF384AMTDX flat panel display DS90CF384AMTDX cross reference

قطعات و اصطلاحات مرتبط

Texas Instruments DS90CF384AMTDX DS90CF384AMTD/NOPB DS90CF384AMTDX/NOPB DS90CF384 LVDS receiver Low-Voltage Differential Signaling LVDS FPD Link Flat Panel Display Link interface IC display interface 24-bit data link 65 MHz 1800 Mbps +3.3 V 56-pin TSSOP TSSOP DGG surface mount SMD controlled-impedance routing differential signaling RoHS REACH AEC-Q100
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ