Texas Instruments

DS90CR216AMTDX - 21-Bit LVDS Receiver | Texas Instruments

MPN: DS90CR216AMTDX ✗ پایان تولید
+3.3 V Vdss 48-pin TSSOP (DGG) Package 66 MHz Speed
حداقل سفارش: 1 |

DS90CR216AMTDX نمای کلی

The Texas Instruments DS90CR216AMTDX is a +3.3 V rising-edge data-strobe LVDS receiver designed for 21-bit Channel Link interfaces operating at up to 66 MHz. It is packaged in a 48-pin TSSOP (DGG) package and is identified by the manufacturer as a 1.386 Gbps LVDS interface device. The receiver is intended for systems that require low-voltage differential signaling across board, cable, or backplane connections where signal integrity, clock recovery, and deterministic data transfer are important. Its single-ended CMOS-side interface works with LVDS signaling on the differential side, helping connect older parallel digital systems to modern high-speed serial links.

The DS90CR216A family is associated with the DS90CR215/DS90CR216 3.3 V rising-edge data-strobe LVDS Channel Link architecture. The 21-bit parallel data path supports transfers of 21 bits per channel at the stated 66 MHz operating frequency, corresponding to the listed 1.386 Gbps class of aggregate signaling performance. The device is a receiver rather than a transmitter, so the system designer must provide the complementary LVDS source, clocking, termination, and downstream logic. The rising-edge data-strobe arrangement supports designs that recover data and transfer timing from the incoming differential signal rather than relying on a separate parallel source-synchronous clock.

The principal engineering benefits are reduced connector pin count compared with a parallel-only implementation, differential noise immunity over longer interconnects, and compatibility with established Channel Link signaling conventions. The 48-pin TSSOP package provides a standard surface-mount footprint and is suitable for compact industrial, communications, and embedded control systems. Because the device operates from a single +3.3 V supply, the power architecture is straightforward, although supply decoupling and LVDS return-path design remain critical.

Typical uses include industrial control links, point-to-point backplanes, embedded video or data acquisition systems, and communication equipment using LVDS over copper. In these applications, the receiver converts a differential LVDS data stream into a 21-bit parallel CMOS data bus while providing the associated strobe or clocking behavior expected by Channel Link designs. The parallel output can connect directly to FPGA, ASIC, DSP, or microcontroller interface logic when voltage, timing, and signal-integrity requirements are satisfied.

A practical design should follow the manufacturer datasheet for pin assignment, termination, decoupling, and layout. Place the receiver close to the connector or cable entry, keep LVDS traces short and tightly matched, provide the required differential termination, and route the outputs to controlled-impedance CMOS destinations. Confirm that the source voltage, cable length, data rate, and downstream input thresholds are compatible before releasing a production board.

This page summarizes the manufacturer product identity, package, interface class, commercial information, and design implications of the DS90CR216AMTDX. It also distinguishes the documented device from related ordering variants and focuses replacement decisions on same-package, pin-compatible LVDS receivers rather than functionally similar but mechanically different parts.

جایگزین‌های drop-in برای DS90CR216AMTDX — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای DS90CR216AMTDX (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Supply Voltage, Data Rate, Number of Pins, Operating Temperature Range, Package.

Texas Instruments
Supply Voltage: 3.3 V
Package: 56-pin TSSOP
مقایسه با DS90CR216AMTDX →
Texas Instruments
Supply Voltage: 3 V to 3.6 V
Data Rate: 1386 Mbps (max)
Number of Pins: 48

DS90CR216MTDX/NOPB

✅ جایگزین مستقیم
Texas Instruments
📦 48-pin TSSOP
Receiver · 3/21 · LVDS · 3 V to 3.6 V · 48-TFSOP (0.240, 6.10mm Width) · Surface Mount · Tape & Reel (TR) · 1386 Mbps (max)

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

DS90CR218MTD

✅ جایگزین مستقیم
📦 48-pin TSSOP
Same 48-pin TSSOP package and documented consistent terminals and main performance characteristics; verify channel width and data-strobe timing before use

📋 جایگزین مرجع (خارج از کاتالوگ)

DS90CR285MTD

✅ جایگزین مستقیم
Texas Instruments
📦 48-pin TSSOP
28-bit Channel Link LVDS transmitter · 3.3 V · 66 MHz · 28 bits · LVCMOS/LVTTL · 4 differential streams · 1 differential stream · 5 LVDS links

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

DS90C385AMTX

✅ جایگزین مستقیم
Texas Instruments
📦 48-pin TSSOP
Programmable LVDS flat-panel-display transmitter · 3.3 V · 87.5 MHz · 85 MHz · 28 bits · 24 bits · 3 bits · 4 differential streams

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

DS90CR216AMTDX/NOPB

✅ جایگزین مستقیم
📦 48-pin TSSOP
Same DS90CR216AMTDX device configuration with the manufacturer /NOPB ordering notation; electrical ratings and pinout are unchanged, with only ordering/marking notation differing

📋 جایگزین مرجع (خارج از کاتالوگ)

DS90CR216AMTDX مشخصات

Product Type LVDS receiver
ولتاژ تغذیه +3.3 V
نرخ داده 1.386 Gbps
Channel Width 21 bits
Clock Frequency 66 MHz
Signaling Type LVDS, rising-edge data strobe
بسته‌بندی 48-pin TSSOP (DGG)
محدوده دمای کاری -40 °C to +85 °C
نوع نصب Surface mount
Input Type LVDS differential data and clock/strobe inputs
نوع خروجی 21-bit parallel CMOS data and strobe outputs
تعداد پین‌ها 48 pins
Packaging Orientation Tape and reel

راهنمای پیکربندی پین DS90CR216AMTDX 48-pin tssop (dgg)

پیکربندی پین برای DS90CR216AMTDX (پکیج 48-pin tssop (dgg)). شماره‌گذاری پایه‌ها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعمل‌های لحیم‌کاری به آن مراجعه کنید.

نمودار پین‌آوت پکیج 48-pin tssop (dgg) برای DS90CR216AMTDX

داده پین‌آوت تفصیلی موجود نیست برای DS90CR216AMTDX.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

DS90CR216AMTDX مناسب است برای 6 کاربردs: Industrial Point-to-Point Data Links, FPGA Communication Interfaces, Video and Data Acquisition, Communication Equipment, Embedded Control and Instrumentation, Legacy LVDS Backplane Retrofit.

🏭

Industrial Point-to-Point Data Links

The DS90CR216AMTDX fits industrial equipment that transfers 21-bit parallel data across a short LVDS cable or backplane connection. Its 66 MHz Channel Link operating frequency and documented 1.386 Gbps signaling class provide a compact differential transport mechanism while reducing connector pin count. The receiver can feed FPGA or ASIC logic with a parallel CMOS bus, provided the system uses the correct data-strobe timing, differential termination, and 3.3 V supply arrangement. For industrial environments, the -40 °C to +85 °C rating is useful, but enclosure temperature, grounding, and cable behavior must be considered.

🖥️

FPGA Communication Interfaces

The DS90CR216AMTDX is useful when an FPGA needs to receive a 21-bit parallel payload from a remote LVDS source. The receiver's 21-bit Channel Link path and rising-edge data-strobe behavior allow the FPGA interface to operate from a compact differential interconnect instead of a wide bus crossing a board or enclosure boundary. The implementation should verify output timing, logic thresholds, clock-to-data relationship, and termination in the FPGA interface specification. The device is especially relevant to legacy LVDS configurations where preserving the existing receiver architecture is more practical than redesigning the source and connector system.

📺

Video and Data Acquisition

The DS90CR216AMTDX can serve as the receiving element in a parallel data-acquisition path where a remote ADC or video source transmits serialized LVDS information and the receiving system reconstructs a 21-bit parallel bus. The 66 MHz Channel Link rate and differential signaling help preserve data integrity across internal cables and board transitions, while the receiver outputs remain close to conventional CMOS logic. Designers should assess whether the source's data-strobe timing, voltage levels, and clocking arrangement match the receiver, and should keep the cable entry and receiver placement short to minimize edge degradation and reflection.

🌐

Communication Equipment

The DS90CR216AMTDX is applicable to communication equipment requiring a compact differential receiver interface for a 21-bit data channel. Its +3.3 V operation, 66 MHz documented Channel Link frequency, and TSSOP-48 package make it suitable for systems that already use Channel Link-style LVDS interconnects. In a rack or board-level design, the receiver can reduce parallel routing pressure while preserving a straightforward CMOS-side interface. Good implementation depends on controlled-impedance differential traces, proper reference-plane continuity, correct source amplitude, and the termination arrangement specified by TI.

🔧

Embedded Control and Instrumentation

The DS90CR216AMTDX can connect a remote instrumentation or embedded-control module to a central controller through an LVDS data link. The 21-bit parallel output provides a practical interface to DSP, FPGA, or microcontroller peripherals, while differential signaling improves noise immunity relative to an exposed single-ended bus. The -40 °C to +85 °C range supports many embedded and industrial environments. System designers should account for the receiver's supply current, CMOS output timing, and the fact that the part is a receiver requiring an external LVDS source rather than a complete transceiver.

🖥️

Legacy LVDS Backplane Retrofit

The DS90CR216AMTDX is appropriate for retrofitting an existing 48-pin TSSOP LVDS receiver position when the original board uses the DS90CR216A Channel Link arrangement. Its same-family alternatives can assist lifecycle planning, but a retrofit should begin with a complete pin-by-pin comparison rather than a package-only substitution. Verify differential input mapping, parallel output mapping, supply pins, ground connections, strobe polarity, and timing margins against the original schematic and TI datasheet. The NRND lifecycle status should also be addressed before committing to a long-term production run.

خلاصه محصولات پیشنهادی

DS90CR216AMTDX Texas Instruments استفاده‌شده در: Industrial Point-to-Point Data Links DS90CR216MTD Texas Instruments استفاده‌شده در: Industrial Point-to-Point Data Links, FPGA Communication Interfaces, Video and Data Acquisition, Communication Equipment, Embedded Control and Instrumentation, Legacy LVDS Backplane Retrofit DS90CR216AMTDX/NOPB exact /NOPB ordering variant استفاده‌شده در: FPGA Communication Interfaces, Communication Equipment, Legacy LVDS Backplane Retrofit DS90CR218MTD same-package receiver candidate استفاده‌شده در: Video and Data Acquisition, Embedded Control and Instrumentation
What is the DS90CR216AMTDX?
The DS90CR216AMTDX is a Texas Instruments +3.3 V rising-edge data-strobe LVDS receiver for 21-bit Channel Link interfaces operating at up to 66 MHz. According to the TI product page and DS90CR216 datasheet listing, the device is packaged in a 48-pin TSSOP (DGG) and is associated with a 1.386 Gbps LVDS signaling class. It converts differential LVDS signaling into a parallel CMOS interface for FPGA, ASIC, DSP, or other digital logic.
What is the operating voltage of DS90CR216AMTDX?
The DS90CR216AMTDX operates from a +3.3 V supply. The TI product page identifies the device as a +3.3 V rising-edge data-strobe LVDS receiver, and the manufacturer ordering information lists the TSSOP (DGG) package with an operating temperature range of -40 °C to +85 °C. Supply rails, decoupling capacitors, and downstream CMOS levels must be checked against the manufacturer datasheet before layout release.
What is the maximum data rate of DS90CR216AMTDX?
The documented signaling performance is 1.386 Gbps, while the Channel Link operating frequency is listed as 66 MHz. The TI product description identifies the part as a 21-bit Channel Link receiver, and the DS90CR216 datasheet listing associates the family with 66 MHz operation. The actual usable link margin still depends on cable length, connector loss, source amplitude, termination, and PCB signal integrity.
Where can I find the DS90CR216AMTDX datasheet and pinout?
The official DS90CR216AMTDX datasheet is available through TI at https://www.ti.com/lit/gpn/ds90cr216, and the product page is https://www.ti.com/product/DS90CR216A. The device uses a 48-pin TSSOP (DGG) package. Use the pin-description table in the manufacturer datasheet when assigning differential inputs, parallel outputs, supply pins, ground pins, and exposed package features.
Is DS90CR216AMTDX still active?
The DS90CR216 is identified as NRND in the TI interface support material included in the product records. NRND means the device is not recommended for new designs, although it may remain available for existing programs. For a new design, review TI's current product and cross-reference information and use the Request a Quote form on this page to confirm lifecycle, availability, and lead time.
Can DS90CR216AMTDX be used with an FPGA?
Yes, the DS90CR216AMTDX is suitable when the FPGA interface uses the device's 21-bit parallel LVDS receiver output and the required +3.3 V CMOS levels. The receiver is intended for 66 MHz Channel Link operation and a documented 1.386 Gbps signaling class. The FPGA logic must be compatible with the receiver's output timing, polarity, strobe behavior, and input-output timing budget.
What is the best drop-in replacement for DS90CR216AMTDX?
The closest documented drop-in choices are the DS90CR216MTD and DS90CR216AMTDX/NOPB ordering forms, plus the related DS90CR218MTD when its interface timing and functional requirements match the design. All identified alternatives use the same 48-pin TSSOP format, but replacement should be confirmed against the TI datasheet pinout, voltage, data width, strobe polarity, and timing requirements. Do not substitute solely by package name.
What is the difference between DS90CR216AMTDX and DS90CR216MTD?
The manufacturer and comparison records identify DS90CR216MTD as a 48-pin TSSOP, 3.3 V LVDS receiver related to the DS90CR216 family, while DS90CR216AMTDX is the specified ordering variant of the DS90CR216A device. The comparison result states that the main performance parameters and terminals are consistent and that replacement does not require circuit modification, but the ordering suffix, temperature grade, and exact marking should still be checked.
DS90CR216AMTDX vs DS90CR218MTD: which receiver is better?
DS90CR218MTD is the more directly documented same-package comparison candidate in the cross-reference data, where it is described as having consistent terminals, package, and main performance characteristics with DS90CR216AMTDX. It should be selected only after confirming that the channel width, data-strobe timing, input/output logic, and operating temperature requirements are equivalent for the intended system. The package match alone does not establish functional equivalence.
When should I choose DS90CR216AMTDX instead of DS90CR218MTD?
Choose DS90CR216AMTDX when the existing system was designed around the DS90CR216A 21-bit, 66 MHz rising-edge data-strobe Channel Link interface and its documented pin assignments are already implemented. Choose DS90CR218MTD only when its manufacturer documentation confirms the same channel width, timing, polarity, supply, and pin behavior. For either choice, verify the complete interface specification rather than relying on the shared TSSOP-48 outline.
Is DS90CR216AMTDX suitable for industrial equipment?
The DS90CR216AMTDX is listed with an operating temperature range of -40 °C to +85 °C, which makes it appropriate for many industrial-temperature applications when the electrical and environmental requirements are otherwise satisfied. The manufacturer lists the DS90CR216 family as NRND, so engineers should confirm lifecycle status and obtain a current quotation through the Request a Quote form before starting a new production design.
What layout considerations apply to DS90CR216AMTDX?
The DS90CR216AMTDX should be placed close to the LVDS connector or cable entry, with short, length-matched differential traces and the manufacturer-specified termination arrangement. Keep the receiver outputs away from noisy sources, provide local supply decoupling, and maintain controlled-impedance routing to downstream CMOS devices. The 48-pin TSSOP footprint is mechanically compatible with the related alternatives, but signal integrity depends on the complete board layout rather than the package alone.
Where can I buy DS90CR216AMTDX and what is the lead time?
Use the Request a Quote form on this page to request the current DS90CR216AMTDX quotation, stock position, minimum order quantity, and lead time from XAIPART. The product is associated with NRND lifecycle status, so availability and production planning should be confirmed for the exact suffix and package. A price figure should not be inferred from an unrelated device or an obsolete family listing.
What is the price of DS90CR216AMTDX?
The current commercial price and available quantity should be obtained through the Request a Quote form on this page because pricing and inventory can change for NRND components. The manufacturer ordering record identifies the exact device as DS90CR216AMTDX/NOPB in a 48-pin TSSOP (DGG), which is the relevant configuration for sourcing. Do not substitute a generic DS90CR216A price for the exact ordering variant.
Is DS90CR216AMTDX in stock?
Stock status should be requested through the Request a Quote form on this page for the exact DS90CR216AMTDX ordering configuration. The manufacturer product information describes the device as NRND, so stock may be constrained and may depend on remaining production or distribution inventory. The quote request should specify the package, tape-and-reel requirement, quantity, and target delivery date.
What are the key specifications of DS90CR216AMTDX that engineers should know?
The key specifications are +3.3 V operation, a 21-bit Channel Link data path, operation up to 66 MHz, and a 1.386 Gbps LVDS signaling class. The part is packaged as a 48-pin TSSOP (DGG) and is specified from -40 °C to +85 °C. The manufacturer describes it as a rising-edge data-strobe LVDS receiver, so timing, strobe polarity, termination, and output-level compatibility are the critical design checks.
What can replace DS90CR216AMTDX?
Documented replacement candidates include DS90CR216MTD, DS90CR216AMTDX/NOPB, DS90CR218MTD, and DS90CR285MTD, with DS90C385AMTX also appearing in a comparison listing. Only parts with the same 48-pin TSSOP footprint and verified pin, voltage, channel-width, and timing compatibility should be considered drop-in replacements. The manufacturer cross-reference search should be used for final qualification before schematic or PCB changes.
Is DS90CR216AMTDX the same as DS90CR216AMTDX/NOPB?
DS90CR216AMTDX and DS90CR216AMTDX/NOPB refer to closely related ordering records for the TI device, but the /NOPB suffix is an ordering notation that must be checked against the manufacturer part-number system. Both records identify the +3.3 V, 48-pin TSSOP (DGG) LVDS receiver family. Engineers should confirm the exact purchasable MPN, marking, tape-and-reel configuration, and lifecycle status on the manufacturer product page.
What is the best TI equivalent for DS90CR216AMTDX?
DS90CR216MTD is the clearest TI same-family drop-in candidate identified in the cross-reference data because it is listed as a 48-pin TSSOP, 3.3 V LVDS receiver with consistent terminals and performance. DS90CR218MTD is another same-package candidate, but its channel width and timing must be verified before substitution. Use TI's cross-reference search and the manufacturer datasheet to confirm the final replacement.

داده‌های مرجع مهندسی برای DS90CR216AMTDX — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the DS90CR216AMTDX when the system already uses a 21-bit, +3.3 V rising-edge data-strobe Channel Link receiver, operates at up to 66 MHz, and requires a 48-pin TSSOP footprint. DS90CR216MTD is the most natural same-family alternative when the original design uses that related ordering form, subject to confirming the exact suffix and timing data. DS90CR218MTD may fit where its documented channel width and timing match, but those details should be verified before release. DS90CR285MTD and DS90C385AMTX are also in the same TSSOP-48 interface family, yet they should be treated as qualified candidates rather than automatic replacements. Because the target is NRND, choose it for legacy support or existing production continuity; for new designs, first confirm lifecycle status and obtain a current quotation through the Request a Quote form.

مقایسه با جایگزین‌ها

پارامتر این محصول DS90CR216MTD DS90CR218MTD DS90CR285MTD DS90C385AMTX
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 48-pin TSSOP 48-pin TSSOP 48-pin TSSOP 48-pin TSSOP 48-pin TSSOP
Product Type LVDS receiver 3.3 V LVDS receiver LVDS receiver LVDS receiver LVDS receiver
Signal Standard Rising-edge data-strobe LVDS Rising-edge data-strobe LVDS LVDS LVDS LVDS

تفاوت‌های کلیدی

  • Same-package same-family replacement path (در مقابلDS90CR216MTD)
  • Documented 21-bit and 66 MHz interface (در مقابلDS90CR218MTD)
  • Exact /NOPB ordering record (در مقابلDS90CR285MTD)
  • 3.3 V Channel Link positioning (در مقابلDS90C385AMTX)

یادداشت‌های طراحی

Place the DS90CR216AMTDX close to the LVDS connector or cable entry and route the differential pair as a short, length-matched pair. Use the termination arrangement specified in the TI datasheet, maintain continuous reference planes, and avoid stubs. The 1.386 Gbps signaling class makes return-path discontinuities, connector transitions, and unequal pair lengths important risks even though the parallel CMOS interface is local to the receiver.

Provide local supply decoupling and route the +3.3 V and ground connections directly to the device pins according to the manufacturer layout guidance. Keep noisy switching regulators, clocks, and high-current return paths away from the LVDS pair. Because the receiver converts differential input into a parallel CMOS output, place the receiver before long parallel routes and terminate the CMOS destination according to the downstream device requirements.

Do not treat a shared TSSOP-48 outline as proof of electrical equivalence. Before substituting DS90CR216MTD, DS90CR218MTD, DS90CR285MTD, or DS90C385AMTX, verify differential input polarity, data-strobe behavior, channel width, output timing, supply levels, and termination. The manufacturer comparison records support same-package review, but final qualification should use the TI datasheet and the original schematic.

The DS90CR216 family is identified as NRND, so a new design should include a lifecycle review rather than relying only on board-level compatibility. The receiver also requires an external LVDS source; it is not a standalone transceiver. Confirm that the source amplitude, cable length, receiver clocking, and downstream timing budget meet the manufacturer requirements before manufacturing.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The available product and comparison records identify the device as an industrial-temperature interface IC, but they do not provide authoritative RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations. AEC-Q100 is not applicable to this non-automotive-specific ordering record.

تاریخ تأیید داده‌ها: 2026-11-16 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

DS90CR216AMTDX datasheet DS90CR216AMTDX pinout DS90CR216AMTDX datasheet pdf DS90CR216AMTDX equivalent DS90CR216AMTDX replacement DS90CR216AMTDX cross reference DS90CR216AMTDX vs DS90CR216MTD DS90CR216AMTDX vs DS90CR218MTD DS90CR216AMTDX price DS90CR216AMTDX stock DS90CR216AMTDX 48-TSSOP Texas Instruments DS90CR216AMTDX DS90CR216AMTDX 1.386 Gbps DS90CR216AMTDX 21-bit LVDS receiver DS90CR216AMTDX Channel Link

قطعات و اصطلاحات مرتبط

Texas Instruments DS90CR216AMTDX DS90CR216A DS90CR216MTD DS90CR218MTD DS90CR285MTD DS90C385AMTX LVDS receiver LVDS Channel Link rising-edge data strobe differential signaling CMOS parallel data interface FPGA ASIC DSP 48-pin TSSOP TSSOP-48 surface mount +3.3 V 1.386 Gbps 66 MHz 21-bit channel industrial-temperature electronics
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ