DS90CR216AMTDX - 21-Bit LVDS Receiver | Texas Instruments
Référence : DS90CR216AMTDX ✗ Fin de vieDS90CR216AMTDX Présentation
The DS90CR216A family is associated with the DS90CR215/DS90CR216 3.3 V rising-edge data-strobe LVDS Channel Link architecture. The 21-bit parallel data path supports transfers of 21 bits per channel at the stated 66 MHz operating frequency, corresponding to the listed 1.386 Gbps class of aggregate signaling performance. The device is a receiver rather than a transmitter, so the system designer must provide the complementary LVDS source, clocking, termination, and downstream logic. The rising-edge data-strobe arrangement supports designs that recover data and transfer timing from the incoming differential signal rather than relying on a separate parallel source-synchronous clock.
The principal engineering benefits are reduced connector pin count compared with a parallel-only implementation, differential noise immunity over longer interconnects, and compatibility with established Channel Link signaling conventions. The 48-pin TSSOP package provides a standard surface-mount footprint and is suitable for compact industrial, communications, and embedded control systems. Because the device operates from a single +3.3 V supply, the power architecture is straightforward, although supply decoupling and LVDS return-path design remain critical.
Typical uses include industrial control links, point-to-point backplanes, embedded video or data acquisition systems, and communication equipment using LVDS over copper. In these applications, the receiver converts a differential LVDS data stream into a 21-bit parallel CMOS data bus while providing the associated strobe or clocking behavior expected by Channel Link designs. The parallel output can connect directly to FPGA, ASIC, DSP, or microcontroller interface logic when voltage, timing, and signal-integrity requirements are satisfied.
A practical design should follow the manufacturer datasheet for pin assignment, termination, decoupling, and layout. Place the receiver close to the connector or cable entry, keep LVDS traces short and tightly matched, provide the required differential termination, and route the outputs to controlled-impedance CMOS destinations. Confirm that the source voltage, cable length, data rate, and downstream input thresholds are compatible before releasing a production board.
This page summarizes the manufacturer product identity, package, interface class, commercial information, and design implications of the DS90CR216AMTDX. It also distinguishes the documented device from related ordering variants and focuses replacement decisions on same-package, pin-compatible LVDS receivers rather than functionally similar but mechanically different parts.
Alternatives de remplacement direct pour DS90CR216AMTDX — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec DS90CR216AMTDX (même facteur de forme et même empreinte) — différant par Supply Voltage, Data Rate, Number of Pins, Operating Temperature Range, Package.
DS90CR216MTDX/NOPB
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →DS90CR218MTD
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DS90CR285MTD
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →DS90C385AMTX
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →DS90CR216AMTDX/NOPB
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
DS90CR216AMTDX Spécifications
| Product Type | LVDS receiver |
| Tension d'alimentation | +3.3 V |
| Débit de données | 1.386 Gbps |
| Channel Width | 21 bits |
| Clock Frequency | 66 MHz |
| Signaling Type | LVDS, rising-edge data strobe |
| Boîtier | 48-pin TSSOP (DGG) |
| Plage de température de fonctionnement | -40 °C to +85 °C |
| Type de montage | Surface mount |
| Input Type | LVDS differential data and clock/strobe inputs |
| Type de sortie | 21-bit parallel CMOS data and strobe outputs |
| Nombre de broches | 48 pins |
| Packaging Orientation | Tape and reel |
Guide de configuration des broches du DS90CR216AMTDX 48-pin tssop (dgg)
Configuration des broches du DS90CR216AMTDX (boîtier 48-pin tssop (dgg)). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour DS90CR216AMTDX.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
DS90CR216AMTDX convient pour 6 applications: Industrial Point-to-Point Data Links, FPGA Communication Interfaces, Video and Data Acquisition, Communication Equipment, Embedded Control and Instrumentation, Legacy LVDS Backplane Retrofit.
Industrial Point-to-Point Data Links
The DS90CR216AMTDX fits industrial equipment that transfers 21-bit parallel data across a short LVDS cable or backplane connection. Its 66 MHz Channel Link operating frequency and documented 1.386 Gbps signaling class provide a compact differential transport mechanism while reducing connector pin count. The receiver can feed FPGA or ASIC logic with a parallel CMOS bus, provided the system uses the correct data-strobe timing, differential termination, and 3.3 V supply arrangement. For industrial environments, the -40 °C to +85 °C rating is useful, but enclosure temperature, grounding, and cable behavior must be considered.
Recommandé
FPGA Communication Interfaces
The DS90CR216AMTDX is useful when an FPGA needs to receive a 21-bit parallel payload from a remote LVDS source. The receiver's 21-bit Channel Link path and rising-edge data-strobe behavior allow the FPGA interface to operate from a compact differential interconnect instead of a wide bus crossing a board or enclosure boundary. The implementation should verify output timing, logic thresholds, clock-to-data relationship, and termination in the FPGA interface specification. The device is especially relevant to legacy LVDS configurations where preserving the existing receiver architecture is more practical than redesigning the source and connector system.
Recommandé
Video and Data Acquisition
The DS90CR216AMTDX can serve as the receiving element in a parallel data-acquisition path where a remote ADC or video source transmits serialized LVDS information and the receiving system reconstructs a 21-bit parallel bus. The 66 MHz Channel Link rate and differential signaling help preserve data integrity across internal cables and board transitions, while the receiver outputs remain close to conventional CMOS logic. Designers should assess whether the source's data-strobe timing, voltage levels, and clocking arrangement match the receiver, and should keep the cable entry and receiver placement short to minimize edge degradation and reflection.
Recommandé
Communication Equipment
The DS90CR216AMTDX is applicable to communication equipment requiring a compact differential receiver interface for a 21-bit data channel. Its +3.3 V operation, 66 MHz documented Channel Link frequency, and TSSOP-48 package make it suitable for systems that already use Channel Link-style LVDS interconnects. In a rack or board-level design, the receiver can reduce parallel routing pressure while preserving a straightforward CMOS-side interface. Good implementation depends on controlled-impedance differential traces, proper reference-plane continuity, correct source amplitude, and the termination arrangement specified by TI.
Recommandé
Embedded Control and Instrumentation
The DS90CR216AMTDX can connect a remote instrumentation or embedded-control module to a central controller through an LVDS data link. The 21-bit parallel output provides a practical interface to DSP, FPGA, or microcontroller peripherals, while differential signaling improves noise immunity relative to an exposed single-ended bus. The -40 °C to +85 °C range supports many embedded and industrial environments. System designers should account for the receiver's supply current, CMOS output timing, and the fact that the part is a receiver requiring an external LVDS source rather than a complete transceiver.
Recommandé
Legacy LVDS Backplane Retrofit
The DS90CR216AMTDX is appropriate for retrofitting an existing 48-pin TSSOP LVDS receiver position when the original board uses the DS90CR216A Channel Link arrangement. Its same-family alternatives can assist lifecycle planning, but a retrofit should begin with a complete pin-by-pin comparison rather than a package-only substitution. Verify differential input mapping, parallel output mapping, supply pins, ground connections, strobe polarity, and timing margins against the original schematic and TI datasheet. The NRND lifecycle status should also be addressed before committing to a long-term production run.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour DS90CR216AMTDX — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | DS90CR216MTD | DS90CR218MTD | DS90CR285MTD | DS90C385AMTX |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 48-pin TSSOP | 48-pin TSSOP | 48-pin TSSOP | 48-pin TSSOP | 48-pin TSSOP |
| Product Type | LVDS receiver | 3.3 V LVDS receiver | LVDS receiver | LVDS receiver | LVDS receiver |
| Signal Standard | Rising-edge data-strobe LVDS | Rising-edge data-strobe LVDS | LVDS | LVDS | LVDS |
Principaux différenciateurs
- Same-package same-family replacement path (vs DS90CR216MTD)
- Documented 21-bit and 66 MHz interface (vs DS90CR218MTD)
- Exact /NOPB ordering record (vs DS90CR285MTD)
- 3.3 V Channel Link positioning (vs DS90C385AMTX)
Notes de conception
Place the DS90CR216AMTDX close to the LVDS connector or cable entry and route the differential pair as a short, length-matched pair. Use the termination arrangement specified in the TI datasheet, maintain continuous reference planes, and avoid stubs. The 1.386 Gbps signaling class makes return-path discontinuities, connector transitions, and unequal pair lengths important risks even though the parallel CMOS interface is local to the receiver.
Provide local supply decoupling and route the +3.3 V and ground connections directly to the device pins according to the manufacturer layout guidance. Keep noisy switching regulators, clocks, and high-current return paths away from the LVDS pair. Because the receiver converts differential input into a parallel CMOS output, place the receiver before long parallel routes and terminate the CMOS destination according to the downstream device requirements.
Do not treat a shared TSSOP-48 outline as proof of electrical equivalence. Before substituting DS90CR216MTD, DS90CR218MTD, DS90CR285MTD, or DS90C385AMTX, verify differential input polarity, data-strobe behavior, channel width, output timing, supply levels, and termination. The manufacturer comparison records support same-package review, but final qualification should use the TI datasheet and the original schematic.
The DS90CR216 family is identified as NRND, so a new design should include a lifecycle review rather than relying only on board-level compatibility. The receiver also requires an external LVDS source; it is not a standalone transceiver. Confirm that the source amplitude, cable length, receiver clocking, and downstream timing budget meet the manufacturer requirements before manufacturing.
Informations de conformité
The available product and comparison records identify the device as an industrial-temperature interface IC, but they do not provide authoritative RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations. AEC-Q100 is not applicable to this non-automotive-specific ordering record.