DSPIC30F4013-30I/P - 16-bit DSC, 30 MIPS, 40-PDIP | Microchip
MPN: DSPIC30F4013-30I/P ✓ فعالDSPIC30F4013-30I/P نمای کلی
What is a Digital Signal Controller? A DSC is a hybrid device that merges the deterministic interrupt response and peripheral set of a microcontroller with the single-cycle MAC, multiply-accumulate engine, and DSP library support of a digital signal processor. In the taxonomy of embedded processors, DSC sits between microcontroller (MCU) and digital signal processor (DSP), with the dsPIC30F family specifically targeting motor control, digital power conversion, and real-time signal conditioning where loop rates of a few to tens of kHz are common.
Key features of the DSPIC30F4013-30I/P include 84 base instructions, a 17x17-bit hardware multiplier, 40 MHz maximum clock (yielding 30 MIPS with a 4-cycle pipeline), and 20 general-purpose digital I/O pins. The device supports 3.0 V to 5.5 V single-supply operation across the industrial -40C to +85C range and provides a JTAG port plus an ICSP in-circuit serial programming interface. The 30I suffix denotes the -40C to +85C industrial operating range.
Architecturally the part uses a modified Harvard layout with separate program and data paths, dual 40-bit accumulators, and barrel shifter support for Q15 fractional math. The on-chip peripherals share a deterministic interrupt controller with 5-cycle latency, enabling the tight control loops required by brushless DC, AC induction, and switched-mode power supply designs.
Typical applications span 3-phase BLDC and PMSM motor drives, switch-mode power supply control loops, sensorless field-oriented control, audio processing front-ends, and industrial sensor conditioning. The 30 MIPS throughput is well-matched to low- to mid-speed drives and converters operating in the 1-50 kHz PWM range.
A key design consideration is input clock strategy - the integrated PLL requires careful loop filter component selection to meet motor-control EMI targets. The PDIP-40 package simplifies breadboard and through-hole prototyping and is widely supported by MPLAB X IDE, the XC16 compiler, and Microchip's motor-control application library.
This page synthesizes distributor pricing, drop-in package variants, and practical design considerations not always visible on a single manufacturer datasheet page.
جایگزین‌های drop-in برای DSPIC30F4013-30I/P — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای DSPIC30F4013-30I/P (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Core Architecture, Package, ADC, Operating Temperature, Timers.
DSPIC30F4013-20I/P
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←DSPIC30F4013-30I/P حداکثر مقادیر مجاز و مشخصات الکتریکی
| Product Type | 16-bit Digital Signal Controller (DSC) |
| Core Architecture | Modified Harvard, dsPIC30F |
| Maximum CPU Speed | 30 MIPS (40 MHz oscillator, 4-cycle pipeline) |
| Program Memory (Flash) | 48 KB |
| RAM | 2 KB |
| Data EEPROM | 1 KB |
| Instruction Set | 84 base instructions, 17x17 hardware multiplier, dual 40-bit accumulators |
| ولتاژ تغذیه | 3.0 V to 5.5 V |
| Digital I/O Pins | 20 |
| ADC | 10-bit, 6 channels (Motor Control PWM-triggered) |
| Motor Control PWM | 6-channel, 16-bit resolution with dead-time control |
| Quadrature Encoder Interface (QEI) | Yes |
| Communication Peripherals | UART, SPI, I2C |
| Timers | 16-bit Timer (x3), 32-bit Timer |
| دمای کاری | -40C to +85C (Industrial) |
| بسته‌بندی | 40-pin PDIP (P) |
| نوع نصب | Through-Hole |
| وضعیت RoHS | Compliant |
پیکربندی پین DSPIC30F4013-30I/P
| پین 1 | EMUD/EMUC — ICD primary communication pair / I/O port |
| پین 2 | AVDD — Analog positive supply |
| پین 3 | AVSS — Analog ground |
| پین 4 | MCLR — Master Clear (reset) input |
| پین 5 | RC15/OSC2/CLKO — Oscillator output / I/O port |
| پین 6 | RC13/SOSC1/SOSCI — Secondary oscillator input / I/O port |
| پین 7 | RC14/SOSC2/SOSCO — Secondary oscillator output / I/O port |
| پین 8 | VDD — Digital positive supply |
| پین 9 | VSS — Digital ground |
| پین 10 | RB0/INT0 — External interrupt 0 / port B |
| پین 11 | RB1/INT1 — External interrupt 1 / port B |
| پین 12 | RB2/INT2 — External interrupt 2 / port B |
| پین 13 | RB3/INT3 — External interrupt 3 / port B |
| پین 14 | RB4/INT4 — External interrupt 4 / port B |
| پین 15 | RB5 — I/O port B |
| پین 16 | RB6/PGEC1 — ICSP clock / port B |
| پین 17 | RB7/PGED1 — ICSP data / port B |
| پین 18 | RD0 — I/O port D |
| پین 19 | RD1 — I/O port D |
| پین 20 | RD2 — I/O port D |
| پین 21 | RD3 — I/O port D |
| پین 22 | RD4 — I/O port D |
| پین 23 | RD5 — I/O port D |
| پین 24 | RD6 — I/O port D |
| پین 25 | RD7 — I/O port D |
| پین 26 | RC1/TXD — UART transmit / port C |
| پین 27 | RC2/SCK/SCL — SPI clock / I2C clock / port C |
| پین 28 | RC3/SDI/SDA — SPI data in / I2C data / port C |
| پین 29 | RC4/SDO — SPI data out / port C |
| پین 30 | RF6/U2RX — UART2 receive / port F |
| پین 31 | RE8/INT1 — External interrupt 1 / port E |
| پین 32 | RE9/INT2 — External interrupt 2 / port E |
| پین 33 | RE0/PWM1H — PWM output 1 high-side / port E |
| پین 34 | RE1/PWM1L — PWM output 1 low-side / port E |
| پین 35 | RE2/PWM2H — PWM output 2 high-side / port E |
| پین 36 | RE3/PWM2L — PWM output 2 low-side / port E |
| پین 37 | RE4/PWM3H — PWM output 3 high-side / port E |
| پین 38 | RE5/PWM3L — PWM output 3 low-side / port E |
| پین 39 | RF7/U2TX — UART2 transmit / port F |
| پین 40 | AVDD — Analog positive supply |
کاربردهای معمول
DSPIC30F4013-30I/P مناسب است برای 6 کاربردs: 3-Phase BLDC / PMSM Motor Drive, Switch-Mode Power Supply (SMPS) Control, Industrial Sensor Signal Conditioning, Audio Processing Front-End, Educational Robotics and Teaching Platforms, Uninterruptible Power Supply (UPS) / Inverter Controllers.
3-Phase BLDC / PMSM Motor Drive
The DSPIC30F4013-30I/P's 6-channel Motor Control PWM with dead-time control and 10-bit ADC triggered from PWM edges makes it a direct fit for 3-phase brushless DC and PMSM motor inverters at switching frequencies typically 8-20 kHz. The QEI module decodes Hall-effect or incremental-encoder feedback for rotor position, while the 30 MIPS throughput handles field-oriented control math within 25 us loop windows.
پیشنهادی
Switch-Mode Power Supply (SMPS) Control
For digital control of isolated and non-isolated DC-DC converters and PFC stages, the DSPIC30F4013-30I/P delivers interrupt latency below 5 cycles that suits current-mode control loops at 50-200 kHz switching frequency. The 10-bit ADC samples inductor current and output voltage with PWM-edge synchronization, while the integrated DSP engine executes PI/PID compensators in fractional Q15 math for fixed-point stability.
پیشنهادی
Industrial Sensor Signal Conditioning
Industrial sensor applications leveraging the DSPIC30F4013-30I/P include temperature, pressure, and flow signal conditioning at the network edge, where its 5 V I/O tolerance simplifies interface to legacy 4-20 mA loops and 24 V sensors. The DSP engine can FIR-filter and decimate the 10-bit ADC stream before passing values over UART/SPI to a host PLC, offloading preprocessing from the upstream controller.
پیشنهادی
Audio Processing Front-End
The DSPIC30F4013-30I/P suits digital audio front-ends such as effects units, parametric EQ, and active crossover controllers operating at 48 kHz sample rates. Its 17x17 hardware multiplier executes biquad IIR and FIR filter coefficients with single-cycle MAC, while SPI pairs with external 16-/24-bit codecs. The 30 MIPS throughput supports 8-16 simultaneous biquad sections per audio channel.
پیشنهادی
Educational Robotics and Teaching Platforms
University courses and robotics kits commonly specify the DSPIC30F4013-30I/P for its through-hole 40-PDIP package, which fits neatly on solderless breadboards and is easy to socket and reprogram. The MPLAB X IDE, the free XC16 compiler, and Microchip's motor-control library lower the barrier for teaching real-time control theory, sensor integration, and DSP algorithm implementation.
پیشنهادی
Uninterruptible Power Supply (UPS) / Inverter Controllers
In single-phase line-interactive UPS systems and solar microinverters, the DSPIC30F4013-30I/P implements grid synchronization, MPPT, and inverter current-control loops. The PWM module generates complementary gate-drive signals with programmable dead-time suited to IGBT half-bridge stages, while the ADC synchronizes to PWM center for low-distortion current sampling across the AC line cycle.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای DSPIC30F4013-30I/P — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | DSPIC30F4013-20I/P |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 40-PDIP | 40-PDIP - same |
| CPU Speed | 30 MIPS (40 MHz) | 20 MIPS (33% slower) |
| Flash Memory | 48 KB | 48 KB (same die) |
| RAM | 2 KB | 2 KB |
| Data EEPROM | 1 KB | 1 KB |
| Motor-Control PWM Channels | 6 channels (16-bit) | 6 channels (16-bit) |
| ADC | 10-bit, 6 channels | 10-bit, 6 channels |
| Supply Voltage | 3.0 V to 5.5 V | 3.0 V to 5.5 V |
| Operating Temperature | -40C to +85C (Industrial, /30I/) | -40C to +85C (Industrial, /20I/) |
تفاوت‌های کلیدی
- Through-hole 40-PDIP package for breadboard prototyping (در مقابلDSPIC30F4013-30I/PT)
- DSC with DSP MAC engine at 30 MIPS (در مقابلDSPIC30F4012-30I/P)
- Single 5 V supply operation without external LDO (در مقابلMCU-only PIC24FJ64GA002)
یادداشت‌های طراحی
The DSPIC30F4013-30I/P has moderate power dissipation in a 40-PDIP package; with typical 5 V VDD and 20-40 mA active current draw the die-to-ambient thermal resistance is acceptable for closed-enclosure industrial designs. Place decoupling capacitors (100 nF X7R close to each VDD/AVDD pin plus a bulk 10 uF tantalum) to minimize internal regulator stress. Estimate: at IDD = 30 mA and 5 V, internal dissipation is approximately 0.15 W; the 40-PDIP package easily dissipates this without a heatsink.
For 40-PDIP breadboard and through-hole prototypes, keep a tight analog/digital supply split: route AVDD/AVSS separately from VDD/VSS with a ferrite bead and cap on each AVSS pin. Place the 10-bit ADC input RC filters (typically 100 ohm + 1 nF) within 5 mm of the ANx pin to suppress PWM edge-coupled noise. GND return paths must not pass under the PLL/OSC traces to avoid jitter.
Estimated: when using the PLL in HS/PLL modes the loop filter component values must match the Microchip-supplied errata for the silicon revision; substituting non-standard resistor/capacitor ratios causes frequency drift or lock failure at temperature extremes. Always use the device configuration bits in the source code to control the oscillator mode and never hardcode fuse settings incorrectly - some early F4013 silicon did not tolerate certain PLL ratios. Validate timing with the MPLAB SIM simulator before hardware bring-up.
The 6-channel Motor Control PWM module produces high dV/dt edges (several kV/us) on the PWM1H/L through PWM3H/L pins; route these as short matched pairs to the gate driver, and keep analog ADC inputs physically separated on the PCB. Ground the MCLR pin through the standard ICSP programming circuit (typically 10 kohm pull-up to VDD with the ICSP reset line driving through a diode or isolator) and never leave MCLR floating.
اطلاعات انطباق
RoHS compliant per Microchip product page data. AEC-Q100 qualification is not standard for this part; for automotive motor-control applications request the AEC-Q100-validated derivative from Microchip. Halogen-free status not explicitly confirmed in the verified data and is left as unknown.
