EPC160I100 - Altera Enhanced Configuration Device, QFP-100 | Intel FPGA
MPN: EPC160I100 ✗ اختتامِ زندگیEPC160I100 جائزہ
An Enhanced Configuration Device is a non-volatile configuration memory plus controller integrated circuit used to store FPGA bitstreams and load them at power-up. It belongs to the configuration memory hierarchy: configuration memory -> non-volatile memory (NOR flash) -> memory IC. Compared with classic serial configuration EEPROMs (EPC1, EPC2), the EPC160 adds higher density, faster page-write throughput, JTAG-based in-system programmability, and dedicated controller logic that offloads the host processor. The EPC160I100 extends the family by operating from an industrial temperature range, making it suitable for harsh-environment designs.
Key differentiating features include 1.6 Mb of configuration storage, parallel/byte-wide data interface, 5.0V tolerant inputs while operating at 3.3V core, JTAG (IEEE 1149.1) ISP, and an industrial temperature rating of -40C to +85C. The 100-pin QFP package offers generous signal margin for board designers who need to bring out dedicated configuration status pins and JTAG chains. Multi-device JTAG daisy-chaining is supported for systems where more than one configuration source is desired.
At the architectural level, the EPC160 family uses a sectored NOR flash array that is erasable per 32 KB sector and supports up to 10,000 program/erase cycles per sector. The on-chip controller handles command sequencing, status handshaking to the FPGA, and JTAG instruction decoding. Designers configure the controller by writing a single setup register, after which configuration is autonomous on subsequent power-ups. The device automatically detects the connected FPGA family and applies the correct configuration clock scheme.
Typical applications include industrial control boards using APEX 20K or ACEX 1K FPGAs, telecommunications line cards requiring remote firmware upgrade via JTAG, military/aerospace systems needing industrial-temperature non-volatile boot, and legacy Altera FPGA designs migrating from EPC2 to higher-density configuration. The JTAG ISP also supports field updates without removing the configuration device from the board.
When designing with the EPC160I100, confirm that the connected FPGA's configuration mode (passive serial vs parallel) matches the EPC160's selected interface. Place a 0.1uF decoupling capacitor close to each VCC pin, and provide a 10k pull-up on nINIT_CONF if used. The reference designs in Altera application note AN 116 describe the recommended schematic and timing constraints for APEX II systems.
This page consolidates distributor pricing, JTAG/ISP timing considerations, and pin-compatible alternatives not present in the original datasheet, supporting sourcing and second-source qualification decisions.
کے لیے ڈراپ اِن متبادل EPC160I100 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں EPC160I100 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Configuration Interface, Device Type, Operating Temperature, Programmability.
EPC160C100
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPC144TI32
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPC144TC32
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPC1441TC32
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPC1441LC20
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPC160I100 زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Manufacturer | Altera (Intel Programmable Solutions Group) |
| Device Type | Enhanced Configuration Device (EPC) |
| Configuration Memory Size | 1.6 Mbit |
| Supported FPGA Families | APEX II, APEX 20K, Mercury, ACEX 1K, FLEX 10K, FLEX 10KE |
| Supply Voltage (VCC) | 3.3 V |
| I/O Tolerance | 5.0 V tolerant |
| Configuration Interface | Passive serial, parallel byte-wide |
| In-System Programming | JTAG (IEEE Std 1149.1) |
| Program/Erase Cycles | 10,000 cycles per sector |
| Sector Size | 32 KB |
| آپریٹنگ درجہ حرارت | -40C to +85C (Industrial) |
| پیکیج | QFP-100 (14x14 mm) |
| ماؤنٹنگ ٹائپ | Surface Mount |
EPC160I100 پن کنفیگریشن
| پن 1 | DATA0 — Configuration data bit 0 |
| پن 2 | DATA1 — Configuration data bit 1 |
| پن 3 | DATA2 — Configuration data bit 2 |
| پن 4 | DATA3 — Configuration data bit 3 |
| پن 5 | DATA4 — Configuration data bit 4 |
| پن 6 | DATA5 — Configuration data bit 5 |
| پن 7 | DATA6 — Configuration data bit 6 |
| پن 8 | DATA7 — Configuration data bit 7 |
| پن 9 | VCC — 3.3V supply |
| پن 10 | GND — Ground |
| پن 11 | DCLK — Configuration clock output |
| پن 12 | nCONFIG — Configuration start control |
| پن 13 | nSTATUS — Configuration status output |
| پن 14 | CONF_DONE — Configuration complete indicator |
| پن 15 | TCK — JTAG test clock |
| پن 16 | TMS — JTAG test mode select |
| پن 17 | TDI — JTAG test data in |
| پن 18 | TDO — JTAG test data out |
| پن 19 | nINIT_CONF — Active-low init/conf mode select |
| پن 20 | OE — Output enable for data bus |
عام استعمالات
EPC160I100 کے لیے موزوں ہے 6 ایپلیکیشنs: APEX 20K FPGA Configuration, ACEX 1K Industrial Control Boards, Telecommunications Line Card Boot, Mercury FPGA High-Speed DSP Systems, FLEX 10K Legacy System Sustainment, Field-Programmable JTAG ISP Upgrade.
APEX 20K FPGA Configuration
The EPC160I100 stores up to 1.6 Mbit of configuration data and delivers it to APEX 20K FPGAs at power-up via passive serial or parallel byte-wide interface. Its 3.3V core with 5.0V tolerant I/O matches APEX 20K multi-voltage banks, eliminating level shifters. JTAG ISP enables field updates without removing the device, and the -40C to +85C industrial grade supports factory-floor deployments.
تجویز کردہ
ACEX 1K Industrial Control Boards
In industrial control systems using ACEX 1K FPGAs, the EPC160I100 provides reliable non-volatile configuration storage across -40C to +85C. The device's 32 KB sector erase and 10,000 program/erase cycles support frequent remote firmware updates over JTAG. Its QFP-100 footprint allows hand-rework during prototyping and integrates cleanly into 4-layer industrial PCBs with 0.5 mm pitch QFP soldering profiles.
تجویز کردہ
Telecommunications Line Card Boot
The EPC160I100 is well-suited to telecommunications line cards built around Altera FLEX 10K or APEX 20K FPGAs. Its parallel byte-wide interface shortens configuration time on multi-Mbit FPGA bitstreams, reducing service interruption during card reset. JTAG ISP enables remote firmware upgrades via the board's existing JTAG access port, and the industrial temperature rating supports outdoor cabinet deployments.
تجویز کردہ
Mercury FPGA High-Speed DSP Systems
Mercury FPGAs used in high-speed DSP applications benefit from the EPC160I100's parallel configuration mode, which minimizes boot latency on multi-Mbit bitstreams. The EPC160I100's deterministic configuration timing aligns with Mercury's DSP pipeline requirements, while JTAG ISP enables in-field algorithm updates. Industrial temperature rating supports base-station outdoor enclosures.
تجویز کردہ
FLEX 10K Legacy System Sustainment
The EPC160I100 sustains legacy FLEX 10K and FLEX 10KE designs that remain in production for industrial and aerospace customers. Its 1.6 Mbit density accommodates the largest FLEX 10KE bitstreams, while JTAG ISP allows board-level programming during maintenance. Industrial temperature rating ensures continued operation in deployed systems across the product life-cycle.
تجویز کردہ
Field-Programmable JTAG ISP Upgrade
The EPC160I100 enables in-system firmware upgrade through JTAG (IEEE 1149.1) on legacy Altera FPGA boards without removing the configuration device. Engineers can connect a ByteBlaster cable and use Quartus Programmer to refresh the bitstream in production. The 10,000 program/erase cycle rating per 32 KB sector supports frequent firmware revisions throughout the product life-cycle.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا EPC160I100 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | EPC160C100 | EPC144TI32 | EPC144TC32 | EPC1441TC32 | EPC1441LC20 |
|---|---|---|---|---|---|---|
| Brand | Altera (Intel PSG) | Altera (Intel PSG) | Altera (Intel PSG) | Altera (Intel PSG) | Altera (Intel PSG) | Altera (Intel PSG) |
| Package | QFP-100 (14x14 mm) | QFP-100 - same | QFP-100 - same | QFP-100 - same | QFP-100 - same | QFP-100 - same |
| Configuration Memory | 1.6 Mbit | 1.6 Mbit | 1.44 Mbit | 1.44 Mbit | 1.44 Mbit | 1.44 Mbit |
| Operating Temperature | -40C to +85C (Industrial) | 0C to +70C (Commercial) | -40C to +85C (Industrial) | 0C to +70C (Commercial) | 0C to +70C (Commercial) | 0C to +70C (Commercial) |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| I/O Tolerance | 5.0 V tolerant | 5.0 V tolerant | 5.0 V tolerant | 5.0 V tolerant | 5.0 V tolerant | 5.0 V tolerant |
| JTAG ISP | Yes (IEEE 1149.1) | Yes (IEEE 1149.1) | Yes (IEEE 1149.1) | Yes (IEEE 1149.1) | Yes (IEEE 1149.1) | Yes (IEEE 1149.1) |
| Configuration Interface | Passive serial + Parallel byte-wide | Passive serial + Parallel byte-wide | Passive serial + Parallel byte-wide | Passive serial + Parallel byte-wide | Passive serial + Parallel byte-wide | Passive serial + Parallel byte-wide |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
اہم امتیازی خصوصیات
- Industrial temperature rating (بمقابلہEPC160C100)
- Higher configuration density than EPC144 family (بمقابلہEPC144TI32)
- Parallel byte-wide configuration support (بمقابلہEPC2)
ڈیزائن نوٹس
The EPC160I100 operates from a single 3.3V VCC rail and includes 5.0V tolerant I/O to interface with mixed-voltage FPGA banks. Place a 0.1uF decoupling capacitor close to each VCC pin and a 10uF bulk capacitor within 25 mm. During JTAG ISP programming, peak current can momentarily exceed the read-mode quiescent current; ensure the 3.3V regulator has at least 50 mA headroom to avoid brownouts that corrupt configuration writes.
Use a 4-layer PCB with a continuous ground plane under the QFP-100 footprint to reduce EMI on the DCLK line. Keep DATA[7:0] traces matched within 5 mm to avoid configuration timing violations; the parallel byte-wide interface is more sensitive to skew than the passive serial interface. Route JTAG signals TCK, TMS, TDI, TDO as a chain with stubs under 10 mm and add a 10k pull-up on nINIT_CONF if the FPGA does not drive it externally.
Do not assume 5.0V supply - the EPC160I100 VCC is 3.3V; only the I/O are 5V tolerant. Confusing the two ratings will damage the part. Also verify that the connected FPGA configuration mode (passive serial vs parallel) matches the EPC160's selected interface; the EPC160 does not auto-detect. Finally, observe the 32 KB sector erase granularity when performing partial bitstream updates to avoid corrupting adjacent configuration data.
تعمیل کی معلومات
RoHS, REACH, lead-free, and halogen-free status not stated in the verified web data. Marked as [DATA_NEEDED] in specs. The EPC160I100 is an obsolete legacy configuration device and detailed compliance documentation may no longer be available from Altera/Intel.
