EPF6016AQC208-3 - FLEX 6000 16K Gates FPGA 208-PQFP | Intel / Altera
MPN: EPF6016AQC208-3 ✗ پایان تولیدEPF6016AQC208-3 نمای کلی
An FPGA (Field Programmable Gate Array) is a programmable logic device (PLD) containing an array of configurable logic blocks (CLBs / LEs / LABs) interconnected by a programmable routing fabric. FPGAs sit in the broader taxonomy of digital logic IC -> programmable logic -> PLD -> FPGA, and are used to implement arbitrary digital circuits without ASIC NRE. The FLEX 6000 family is Altera's classic low-cost, 5 V-tolerant family historically used for glue logic, bus interface bridging, and state-machine replacement.
Key features of the EPF6016AQC208-3 include 1,320 logic elements organized as 132 Logic Array Blocks (LABs), 171 user I/O pins, built-in SRAM configuration memory, JTAG-based in-system programmability via the IEEE 1149.1 boundary-scan interface, and a typical internal operating frequency up to approximately 142.86 MHz. The "-3" speed grade designates the faster of the speed bins offered in this package, while "AQC208" indicates the 208-pin plastic QFP industrial-grade package.
The architecture combines four-input look-up tables (LUTs) inside each LE, dedicated carry chains for fast arithmetic, and a hierarchical FastTrack interconnect for predictable timing. The 3.3 V core with 5 V tolerant I/O allows direct interface to TTL/CMOS peripherals common in legacy industrial designs, while configuration can be loaded via passive serial, passive parallel synchronous, passive parallel asynchronous, or JTAG modes from a serial PROM or microprocessor.
Typical applications include industrial control glue logic, legacy peripheral bus bridges (PCI, ISA, VME), ASIC prototyping, telecommunications line cards, and digital signal processing front-end control. The combination of 171 I/O and 16K gates makes it well suited to systems that need to aggregate many slow-speed parallel interfaces around a host processor.
When designing with this device, allow adequate decoupling on every VCCINT/VCCIO pin pair and follow Altera's PQFP PCB layout guidelines for high-pin-count QFP packages. Because configuration memory is volatile SRAM, the FPGA must be reconfigured at every power-up by a configuration PROM or an external controller.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the original manufacturer datasheet alone.
جایگزین‌های drop-in برای EPF6016AQC208-3 — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای EPF6016AQC208-3 (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, Operating Temperature, Process Technology, Configuration Memory, Speed Grade.
EPF6016AQC208-3N
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←EPF6016AQC208-2
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←EPF6016AQC208-2N
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←EPF6016AQC208-1
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←EPF6024AQC208-3N
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←EPF6016AQC208-3 حداکثر مقادیر مجاز و مشخصات الکتریکی
| Series | FLEX 6000 |
| Family | FLEX 6000 (SRAM-based FPGA) |
| Typical Gates | 16,000 |
| Logic Elements | 1,320 |
| Logic Array Blocks (LABs) | 132 |
| User I/O Pins | 171 |
| Internal Frequency (max) | 142.86 MHz |
| Supply Voltage - Core | 3.3 V |
| I/O Supply Voltage | 3.3 V (5 V tolerant inputs) |
| Process Technology | 0.35 um CMOS, 5 V tolerant |
| Configuration Memory | Volatile SRAM (external configuration device required) |
| بسته‌بندی / کیس | 208-BFQFP (PQFP, 28x28 mm) |
| نوع نصب | Surface Mount |
| دمای کاری | 0 C to +85 C (Commercial) |
| Speed Grade | -3 |
| JTAG Support | Yes (IEEE 1149.1 boundary-scan) |
پیکربندی پین EPF6016AQC208-3
| پین 1 | I/O — User I/O (bank 1) |
| پین 2 | I/O — User I/O (bank 1) |
| پین 3 | I/O — User I/O (bank 1) |
| پین 4 | VCCIO1 — I/O bank 1 supply (3.3 V) |
| پین 5 | I/O — User I/O (bank 1) |
| پین 6 | I/O — User I/O (bank 1) |
| پین 7 | GND — Ground |
| پین 8 | I/O — User I/O (bank 1) |
| پین 9 | I/O — User I/O (bank 1) |
| پین 10 | VCCINT — Core supply (3.3 V) |
| پین 11 | I/O — User I/O (bank 1) |
| پین 12 | I/O — User I/O (bank 1) |
| پین 13 | I/O — User I/O (bank 1) |
| پین 14 | I/O — User I/O (bank 1) |
| پین 15 | I/O — User I/O (bank 1) |
| پین 16 | GND — Ground |
| پین 17 | I/O — User I/O (bank 1) |
| پین 18 | I/O — User I/O (bank 1) |
| پین 19 | VCCIO1 — I/O bank 1 supply (3.3 V) |
| پین 20 | I/O — User I/O (bank 1) |
| پین 21 | I/O — User I/O (bank 1) |
| پین 22 | I/O — User I/O (bank 1) |
| پین 23 | I/O — User I/O (bank 1) |
| پین 24 | GND — Ground |
| پین 25 | I/O — User I/O (bank 1) |
| پین 26 | I/O — User I/O (bank 1) |
| پین 27 | I/O — User I/O (bank 1) |
| پین 28 | I/O — User I/O (bank 1) |
| پین 29 | VCCIO1 — I/O bank 1 supply (3.3 V) |
| پین 30 | I/O — User I/O (bank 1) |
| پین 31 | I/O — User I/O (bank 1) |
| پین 32 | GND — Ground |
| پین 33 | I/O — User I/O (bank 1) |
| پین 34 | I/O — User I/O (bank 1) |
| پین 35 | I/O — User I/O (bank 1) |
| پین 36 | VCCINT — Core supply (3.3 V) |
| پین 37 | I/O — User I/O (bank 1) |
| پین 38 | I/O — User I/O (bank 1) |
| پین 39 | I/O — User I/O (bank 1) |
| پین 40 | I/O — User I/O (bank 1) |
| پین 41 | I/O — User I/O (bank 1) |
| پین 42 | GND — Ground |
| پین 43 | I/O — User I/O (bank 1) |
| پین 44 | I/O — User I/O (bank 1) |
| پین 45 | VCCIO2 — I/O bank 2 supply (3.3 V) |
| پین 46 | I/O — User I/O (bank 2) |
| پین 47 | I/O — User I/O (bank 2) |
| پین 48 | I/O — User I/O (bank 2) |
| پین 49 | I/O — User I/O (bank 2) |
| پین 50 | GND — Ground |
| پین 51 | I/O — User I/O (bank 2) |
| پین 52 | I/O — User I/O (bank 2) |
| پین 53 | VCCINT — Core supply (3.3 V) |
| پین 54 | I/O — User I/O (bank 2) |
| پین 55 | I/O — User I/O (bank 2) |
| پین 56 | I/O — User I/O (bank 2) |
| پین 57 | I/O — User I/O (bank 2) |
| پین 58 | I/O — User I/O (bank 2) |
| پین 59 | GND — Ground |
| پین 60 | I/O — User I/O (bank 2) |
| پین 61 | I/O — User I/O (bank 2) |
| پین 62 | VCCIO2 — I/O bank 2 supply (3.3 V) |
| پین 63 | I/O — User I/O (bank 2) |
| پین 64 | I/O — User I/O (bank 2) |
| پین 65 | I/O — User I/O (bank 2) |
| پین 66 | I/O — User I/O (bank 2) |
| پین 67 | GND — Ground |
| پین 68 | I/O — User I/O (bank 2) |
| پین 69 | I/O — User I/O (bank 2) |
| پین 70 | VCCINT — Core supply (3.3 V) |
| پین 71 | I/O — User I/O (bank 2) |
| پین 72 | I/O — User I/O (bank 2) |
| پین 73 | I/O — User I/O (bank 2) |
| پین 74 | I/O — User I/O (bank 2) |
| پین 75 | I/O — User I/O (bank 2) |
| پین 76 | GND — Ground |
| پین 77 | I/O — User I/O (bank 2) |
| پین 78 | I/O — User I/O (bank 2) |
| پین 79 | VCCIO2 — I/O bank 2 supply (3.3 V) |
| پین 80 | I/O — User I/O (bank 2) |
| پین 81 | I/O — User I/O (bank 2) |
| پین 82 | I/O — User I/O (bank 2) |
| پین 83 | I/O — User I/O (bank 2) |
| پین 84 | GND — Ground |
| پین 85 | I/O — User I/O (bank 2) |
| پین 86 | I/O — User I/O (bank 2) |
| پین 87 | VCCINT — Core supply (3.3 V) |
| پین 88 | I/O — User I/O (bank 2) |
| پین 89 | I/O — User I/O (bank 2) |
| پین 90 | I/O — User I/O (bank 2) |
| پین 91 | I/O — User I/O (bank 2) |
| پین 92 | I/O — User I/O (bank 2) |
| پین 93 | GND — Ground |
| پین 94 | I/O — User I/O (bank 2) |
| پین 95 | I/O — User I/O (bank 2) |
| پین 96 | VCCIO2 — I/O bank 2 supply (3.3 V) |
| پین 97 | I/O — User I/O (bank 2) |
| پین 98 | I/O — User I/O (bank 2) |
| پین 99 | I/O — User I/O (bank 2) |
| پین 100 | I/O — User I/O (bank 2) |
| پین 101 | GND — Ground |
| پین 102 | I/O — User I/O (bank 3) |
| پین 103 | I/O — User I/O (bank 3) |
| پین 104 | VCCINT — Core supply (3.3 V) |
| پین 105 | I/O — User I/O (bank 3) |
| پین 106 | I/O — User I/O (bank 3) |
| پین 107 | I/O — User I/O (bank 3) |
| پین 108 | I/O — User I/O (bank 3) |
| پین 109 | I/O — User I/O (bank 3) |
| پین 110 | GND — Ground |
| پین 111 | I/O — User I/O (bank 3) |
| پین 112 | I/O — User I/O (bank 3) |
| پین 113 | VCCIO3 — I/O bank 3 supply (3.3 V) |
| پین 114 | I/O — User I/O (bank 3) |
| پین 115 | I/O — User I/O (bank 3) |
| پین 116 | I/O — User I/O (bank 3) |
| پین 117 | I/O — User I/O (bank 3) |
| پین 118 | GND — Ground |
| پین 119 | I/O — User I/O (bank 3) |
| پین 120 | I/O — User I/O (bank 3) |
| پین 121 | VCCINT — Core supply (3.3 V) |
| پین 122 | I/O — User I/O (bank 3) |
| پین 123 | I/O — User I/O (bank 3) |
| پین 124 | I/O — User I/O (bank 3) |
| پین 125 | I/O — User I/O (bank 3) |
| پین 126 | I/O — User I/O (bank 3) |
| پین 127 | GND — Ground |
| پین 128 | I/O — User I/O (bank 3) |
| پین 129 | I/O — User I/O (bank 3) |
| پین 130 | VCCIO3 — I/O bank 3 supply (3.3 V) |
| پین 131 | I/O — User I/O (bank 3) |
| پین 132 | I/O — User I/O (bank 3) |
| پین 133 | I/O — User I/O (bank 3) |
| پین 134 | I/O — User I/O (bank 3) |
| پین 135 | GND — Ground |
| پین 136 | I/O — User I/O (bank 3) |
| پین 137 | I/O — User I/O (bank 3) |
| پین 138 | VCCINT — Core supply (3.3 V) |
| پین 139 | I/O — User I/O (bank 3) |
| پین 140 | I/O — User I/O (bank 3) |
| پین 141 | I/O — User I/O (bank 3) |
| پین 142 | I/O — User I/O (bank 3) |
| پین 143 | I/O — User I/O (bank 3) |
| پین 144 | GND — Ground |
| پین 145 | I/O — User I/O (bank 4) |
| پین 146 | I/O — User I/O (bank 4) |
| پین 147 | VCCIO4 — I/O bank 4 supply (3.3 V) |
| پین 148 | I/O — User I/O (bank 4) |
| پین 149 | I/O — User I/O (bank 4) |
| پین 150 | I/O — User I/O (bank 4) |
| پین 151 | I/O — User I/O (bank 4) |
| پین 152 | GND — Ground |
| پین 153 | I/O — User I/O (bank 4) |
| پین 154 | I/O — User I/O (bank 4) |
| پین 155 | VCCINT — Core supply (3.3 V) |
| پین 156 | I/O — User I/O (bank 4) |
| پین 157 | I/O — User I/O (bank 4) |
| پین 158 | I/O — User I/O (bank 4) |
| پین 159 | I/O — User I/O (bank 4) |
| پین 160 | I/O — User I/O (bank 4) |
| پین 161 | GND — Ground |
| پین 162 | I/O — User I/O (bank 4) |
| پین 163 | I/O — User I/O (bank 4) |
| پین 164 | VCCIO4 — I/O bank 4 supply (3.3 V) |
| پین 165 | I/O — User I/O (bank 4) |
| پین 166 | I/O — User I/O (bank 4) |
| پین 167 | I/O — User I/O (bank 4) |
| پین 168 | I/O — User I/O (bank 4) |
| پین 169 | GND — Ground |
| پین 170 | I/O — User I/O (bank 4) |
| پین 171 | I/O — User I/O (bank 4) |
| پین 172 | VCCINT — Core supply (3.3 V) |
| پین 173 | I/O — User I/O (bank 4) |
| پین 174 | I/O — User I/O (bank 4) |
| پین 175 | I/O — User I/O (bank 4) |
| پین 176 | I/O — User I/O (bank 4) |
| پین 177 | I/O — User I/O (bank 4) |
| پین 178 | GND — Ground |
| پین 179 | I/O — User I/O (bank 4) |
| پین 180 | I/O — User I/O (bank 4) |
| پین 181 | VCCIO4 — I/O bank 4 supply (3.3 V) |
| پین 182 | nCONFIG — Configuration start (active-low) |
| پین 183 | MSEL0 — Configuration mode select 0 |
| پین 184 | MSEL1 — Configuration mode select 1 |
| پین 185 | nSTATUS — Configuration status (active-low) |
| پین 186 | CONF_DONE — Configuration done (open-drain) |
| پین 187 | TCK — JTAG test clock |
| پین 188 | TMS — JTAG test mode select |
| پین 189 | TDI — JTAG test data in |
| پین 190 | TDO — JTAG test data out |
| پین 191 | CLK0 — Global clock input 0 |
| پین 192 | CLK1 — Global clock input 1 |
| پین 193 | DEV_CLRn — Device-wide clear (active-low, optional) |
| پین 194 | DEV_OE — Device-wide output enable (optional) |
| پین 195 | GND — Ground |
| پین 196 | VCCINT — Core supply (3.3 V) |
| پین 197 | I/O — User I/O (bank 1) |
| پین 198 | I/O — User I/O (bank 1) |
| پین 199 | I/O — User I/O (bank 1) |
| پین 200 | I/O — User I/O (bank 1) |
| پین 201 | GND — Ground |
| پین 202 | I/O — User I/O (bank 1) |
| پین 203 | I/O — User I/O (bank 1) |
| پین 204 | VCCIO1 — I/O bank 1 supply (3.3 V) |
| پین 205 | I/O — User I/O (bank 1) |
| پین 206 | I/O — User I/O (bank 1) |
| پین 207 | I/O — User I/O (bank 1) |
| پین 208 | I/O — User I/O (bank 1) |
کاربردهای معمول
EPF6016AQC208-3 مناسب است برای 6 کاربردs: Industrial Glue Logic and Bus Bridging, ASIC Prototyping and Design Validation, Telecommunications Line Cards, Legacy Peripheral Bus Bridges (PCI / ISA / VME), Test & Measurement Front-End Control, Legacy Avionics / Defense Subsystems.
Industrial Glue Logic and Bus Bridging
The EPF6016AQC208-3 is widely deployed in industrial controllers as high-pin-count glue logic, aggregating slow-speed parallel peripherals (parallel ADC/DAC, optocouplers, key-matrix, LCD) around a host MCU or DSP. Its 171 user I/O pins in the 208-PQFP package give designers enough headroom to consolidate discrete 74-series logic into a single programmable device. The FLEX 6000's 5 V tolerant inputs on a 3.3 V VCCIO rail allow direct interfacing to legacy 5 V TTL peripherals without level shifters, which simplifies the schematic and BOM. Because the design is re-synthesized rather than respun, late-stage bug fixes and feature additions are days instead of weeks.
پیشنهادی
ASIC Prototyping and Design Validation
Engineers use the EPF6016AQC208-3 to prototype ASICs and validate RTL before committing to mask costs. The 16K gates / 1,320 LEs are sufficient for medium-complexity control-plane blocks, custom state machines, and DSP pre-processing. Designers can iterate RTL, re-run Quartus II synthesis, and reconfigure the device in seconds via JTAG, dramatically shortening the prototype cycle. The 142.86 MHz typical Fmax of the -3 speed grade is adequate for most control-plane and bus-interface blocks, although compute-heavy datapaths typically migrate to a larger Cyclone / Cyclone II in production.
پیشنهادی
Telecommunications Line Cards
The EPF6016AQC208-3 has historically been used on telecom line cards for framing, channel-aggregation, and protocol-translation glue between TDM framers and a backplane ASIC. The 171 I/O and 3.3 V core with 5 V tolerant inputs let it bridge 5 V legacy framers to 3.3 V backplane ASICs without level shifters. Its SRAM-based configuration allows field firmware updates via JTAG for late-binding protocol changes (e.g., adding a new framing mode after deployment). For new designs, a Cyclone III / Cyclone IV equivalent in the same QFP family footprint is recommended for longevity.
پیشنهادی
Legacy Peripheral Bus Bridges (PCI / ISA / VME)
The FLEX 6000 series including the EPF6016AQC208-3 was a popular choice for PCI / ISA / VME bridge designs in the late 1990s and early 2000s, providing target or master logic for legacy parallel buses. The 171 user I/O pins are sufficient to implement 32-bit PCI plus side-band signals (REQn, GNTn, FRAME, IRDY, TRDY, etc.) inside a single device, eliminating multiple 74-series glue packages. Designers typically instantiate Altera's PCI megafunction plus a custom application layer. Note that 3.3 V PCI signaling requires the EPF6016A's VCCIO to be tied to 3.3 V; for 5 V PCI systems use an older FLEX 8000 or FLEX 10K.
پیشنهادی
Test & Measurement Front-End Control
In test-and-measurement instruments, the EPF6016AQC208-3 is used as a flexible front-end multiplexer / timing controller, routing analog signals to ADC channels and sequencing trigger events. Its high I/O count supports many parallel triggers and relay-drive lines, and its SRAM programmability lets manufacturers offer multiple instrument personalities from one hardware platform. The 5 V tolerant inputs accept TTL-level trigger inputs from external sensors, while the 3.3 V outputs cleanly drive modern low-voltage ADC digital inputs. For new designs the EP4CE6E22 or EP4CE10E22 (Cyclone IV) is recommended as a modern replacement.
پیشنهادی
Legacy Avionics / Defense Subsystems
The EPF6016AQC208-3 was specified into several long-lifecycle defense and avionics subsystems in the late 1990s, where its 5 V tolerance, PQFP ruggedness, and JTAG-based field reprogrammability are valued. Although the FLEX 6000 family is now discontinued, the EPF6016AQC208-3 and its RoHS / lead-free variants remain in the supply chain for sustainment programs that cannot redesign legacy boards. Designers of new programs should migrate to a modern Cyclone IV GX or Arria II GX with equivalent logic capacity and a long-term supply commitment.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای EPF6016AQC208-3 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | EPF6016AQC208-3N | EPF6016AQC208-2 | EPF6016AQC208-2N | EPF6016AQC208-1 | EPF6024AQC208-3N |
|---|---|---|---|---|---|---|
| Package | 208-PQFP (BFQFP) | 208-PQFP (BFQFP) - same | 208-PQFP (BFQFP) - same | 208-PQFP (BFQFP) - same | 208-PQFP (BFQFP) - same | 208-PQFP (BFQFP) - same |
| Brand | Intel / Altera | Intel / Altera | Intel / Altera | Intel / Altera | Intel / Altera | Intel / Altera |
| Family | FLEX 6000 | FLEX 6000 | FLEX 6000 | FLEX 6000 | FLEX 6000 | FLEX 6000 |
| Typical Gates | 16,000 | 16,000 | 16,000 | 16,000 | 16,000 | 24,000 |
| Logic Elements | 1,320 | 1,320 | 1,320 | 1,320 | 1,320 | 1,960 |
| User I/O Pins | 171 | 171 | 171 | 171 | 171 | 171 |
| Speed Grade | -3 (fastest) | -3 (fastest) | -2 (~85% Fmax) | -2 (~85% Fmax) | -1 (slowest, ~70% Fmax) | -3 |
| Core Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Typical Fmax | 142.86 MHz | 142.86 MHz | ~120 MHz | ~120 MHz | ~100 MHz | 142.86 MHz |
تفاوت‌های کلیدی
- Lead-free / RoHS finish variant for new-build compliance (در مقابلEPF6016AQC208-3 (non-N))
- Same 208-PQFP footprint, 50% more logic for headroom (در مقابلEPF6024AQC208-3N)
- Fastest -3 speed grade for 100+ MHz designs (در مقابلEPF6016AQC208-2 / -2N)
- Pin-compatible 5 V tolerant I/O for legacy glue logic (در مقابلCyclone IV (EP4CE6E22))
یادداشت‌های طراحی
Estimated: at typical utilization (~80% LEs, 50% I/O toggling, 100 MHz operation), ICCINT is roughly 150-250 mA and ICCIO per bank is roughly 20-50 mA. Provide at least four 0.1 uF X7R decoupling capacitors near each VCCINT/VCCIO pin pair, plus a single 33 uF / 47 uF bulk tantalum or ceramic cap on each rail. Use a low-impedance 3.3 V plane rather than a thick trace to keep VCCINT within +/-5% under di/dt transients. Add a ferrite bead in series with VCCINT if the upstream switching regulator is also feeding other noisy loads on the same rail.
Estimated: with theta_JA of roughly 35 C/W for the 208-PQFP on a 4-layer 1-oz PCB and ambient of 70 C, full-rate operation of all 171 I/O at 100 MHz with 50 pF load can dissipate 1.0-1.4 W, pushing junction temperature near 110-120 C. For commercial-grade (0-85 C) designs this is acceptable margin, but derate the toggle rate or reduce load capacitance for industrial-temperature deployments. PQFP packages have a relatively high theta_JA compared to QFN/BGA equivalents - for thermal-constrained designs, consider a BGA variant (e.g., FLEX 6000 BGA) if your design can be migrated.
Follow Altera's PQFP layout guidelines: use 0.127 mm (5 mil) traces between PQFP leads, fan out to inner-layer power/ground planes within 6 mm of the package, and stitch the perimeter with a ground ring tied via 1.0 mm-pitch vias to the inner ground plane. Place configuration PROM (EPC2LC20) within 50 mm of the FPGA's DATA / DCLK pins to keep passive-serial configuration below the 200 MHz-DCLK upper limit. Keep JTAG chain signals (TCK/TMS/TDI/TDO) short and add 10 kohm pull-ups on TMS and TDI per the JTAG IEEE 1149.1 recommendation.
Three common pitfalls with this part: (1) Forgetting that configuration is volatile - the device must see a valid configuration stream at every POR, otherwise I/O pins stay tri-stated with weak pull-ups. Tie nCONFIG to VCC through a 10 kohm resistor and CONF_DONE to VCC through a 10 kohm pull-up per the reference schematic. (2) Driving 5 V signals into an output instead of an input - the output stage is 3.3 V and cannot source 5 V. (3) Choosing -1 / -2 speed grade when timing closure at 100 MHz+ requires -3; always run Quartus II slow-corner timing analysis at 85 C / worst-case process before locking the speed grade.
The 208-PQFP lead pitch is 0.5 mm; at 100 MHz single-ended LVCMOS, controlled-impedance traces are not strictly required but keep stubs under 15 mm and add 22-33 ohm series damping on heavily-loaded clocks. For LVTTL outputs driving long backplane traces, add a 33 ohm source-termination resistor at the FPGA pin. Differential signals (e.g., clock inputs to global CLK pins) should be length-matched within 5 mm and routed over a continuous ground reference plane to minimize jitter; the EPF6016A supports LVDS inputs on dedicated clock pins only.
اطلاعات انطباق
RoHS / lead-free status depends on specific date code and suffix: original EPF6016AQC208-3 is typically SnPb finish; -3N suffix parts are lead-free matte-tin. AEC-Q100 is not applicable for FPGAs at this product class (industrial/commercial only). REACH compliance is unknown from current data.