INA143UA/2K5 - 5V/us Precision Difference Amp | TI
MPN: INA143UA/2K5 ✓ فعالINA143UA/2K5 نمای کلی
A difference amplifier is a specialized operational-amplifier circuit that amplifies the voltage difference between two input nodes while rejecting signals common to both inputs. The INA143 belongs to the instrumentation-amplifier and precision differential-amplifier hierarchy, combining an operational amplifier with matched internal resistors. This makes it suitable for sensing small differential voltages in industrial, instrumentation, and signal-conditioning systems without requiring a discrete resistor network.
The principal features include a 5 V/us slew rate, 250 uV input offset, selectable gains of 10 and 0.1, and laser-trimmed resistors for accurate gain. The manufacturer identifies the device as a precision difference amplifier optimized for high-speed applications. Its differential architecture improves common-mode rejection, while the internal resistor network reduces component-count and calibration requirements compared with a discrete implementation.
The INA143UA/2K5 is supplied in an 8-pin SOIC package marked D, with an operating temperature range of -40 C to +85 C. The UA ordering option uses a tape-and-reel format, and the /2K5 suffix denotes a 2500-unit reel. As a single-circuit device, it offers one amplifier per package and is intended for precision analog signal chains rather than high-channel-count systems.
Typical uses include current-sense amplifier signal conditioning, bridge-sensor front ends, industrial measurement systems, medical instrumentation, and differential communications. Its selectable gain supports both 10:1 attenuation of larger differential signals and 10:1 amplification of smaller signals when the appropriate device configuration is selected. The high slew rate also makes it suitable for waveforms that must be amplified without excessive distortion.
Designers should preserve the differential signal path, compare input and output swing against the actual operating voltage, and validate common-mode range at the selected gain. Because the gain choice changes input impedance and common-mode performance, the gain setting must be confirmed against the manufacturer’s pin and electrical tables before finalizing the PCB layout.
This page combines manufacturer specifications, drop-in alternatives, application guidance, pin-level planning support, and a parameter comparison for engineers evaluating the INA143UA/2K5 in precision analog designs.
جایگزینهای drop-in برای INA143UA/2K5 — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای INA143UA/2K5 (همان فرمفاکتور و فوتپرینت) — متفاوت در Operating Temperature Range, Package, Slew Rate, Amplifier Type, Common-Mode Rejection Ratio.
INA143U/2K5
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←INA141UA/2K5
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←INA155UA/2K5
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
INA132U/2K5
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←AD8278ARZ
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
INA143UA/2K5 حداکثر مقادیر مجاز و مشخصات الکتریکی
| Product Type | Precision difference amplifier |
| Amplifier Type | Single-channel differential amplifier |
| Number of Circuits | 1 circuit |
| Slew Rate | 5 V/us |
| Input Offset Voltage | 250 uV |
| Gain Options | 10 or 0.1 |
| Internal Resistor Network | Laser trimmed |
| Common-Mode Rejection Ratio | 96 dB |
| محدوده دمای کاری | -40 C to +85 C |
| بستهبندی | 8-pin SOIC (D) |
| نوع نصب | Surface mount |
| Standard Reel Quantity | 2500 units |
راهنمای پیکربندی پین INA143UA/2K5 8-pin soic (d)
پیکربندی پین برای INA143UA/2K5 (پکیج 8-pin soic (d)). این قطعه آنالوگ دارای پینهای ورودی، خروجی و تغذیه است. برای پیکربندیهای پین offset null، جبرانسازی و فعالسازی به دیتاشیت سازنده مراجعه کنید. ایدهآل برای مدارهای شرطیسازی سیگنال و تقویتکننده.
داده پینآوت تفصیلی موجود نیست برای INA143UA/2K5.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
INA143UA/2K5 مناسب است برای 6 کاربردs: Motor Current-Sense Amplification, Bridge Sensor Signal Conditioning, Medical Instrumentation Signal Chain, Industrial Sensor Interface, Balanced Audio and Communication Input, Power Converter Feedback Interface.
Motor Current-Sense Amplification
INA143UA/2K5 fits high-side or low-side shunt monitoring when the measured differential voltage is small and the common-mode voltage remains within the permitted input range. Its selectable gains of 10 and 0.1, 250 uV offset, and 5 V/us slew rate help preserve small current information while tracking dynamic motor current. A matched Kelvin connection from the shunt reduces trace-imbalance error, while input filtering can limit PWM-edge noise. Before implementation, verify the maximum common-mode voltage, shunt transient amplitude, amplifier output swing, and the INA143 gain-network pin configuration against the manufacturer’s recommended circuit.
پیشنهادی
Bridge Sensor Signal Conditioning
INA143UA/2K5 is appropriate for bridge-based pressure, strain, and position sensing because its differential input architecture suppresses common-mode excitation and system noise. The 250 uV offset supports low-level bridge outputs, while selectable gain of 10 or 0.1 provides flexibility for sensor sensitivity and analog headroom. Route the bridge excitation, sensor inputs, and analog ground to minimize thermoelectric offsets and parasitic currents. A practical design should use the specified gain-network configuration, verify the bridge excitation voltage against the input common-mode range, and check that the output remains linear across the full sensor travel.
پیشنهادی
Medical Instrumentation Signal Chain
INA143UA/2K5 can amplify low-level physiological or diagnostic signals when the front end requires fast settling and differential rejection. Its 250 uV offset, 5 V/us slew rate, and selectable gain of 10 or 0.1 allow a compact conditioning stage between a sensor and an ADC. For sensitive analog paths, use guarded grounding, symmetrical input routing, and filtering that does not compromise the required signal bandwidth. The designer should also evaluate noise, input bias current, recovery behavior, and isolation requirements according to the complete manufacturer electrical specification.
پیشنهادی
Industrial Sensor Interface
INA143UA/2K5 provides a practical differential input stage for industrial sensors that generate small voltages on a larger common-mode baseline. The selectable gain of 10 or 0.1 accommodates both attenuation and amplification needs, while the 96 dB common-mode rejection figure supports interference suppression in multi-sensor systems. Place the amplifier close to the sensor connector, keep input traces short and symmetrical, and provide local bypassing for the supply rails. Confirm the industrial operating temperature, transient limits, and supply range before using the device in machinery or process-control equipment.
پیشنهادی
Balanced Audio and Communication Input
INA143UA/2K5 can condition balanced low-level analog signals when differential rejection and fast slew performance are more important than a zero-offset dual supply. The selectable gain of 10 or 0.1 helps adapt the amplifier to source level, and the 250 uV offset supports precision signal chains. Use matched input routing and appropriate termination to minimize common-mode conversion and ground imbalance. Verify the output swing, input common-mode range, noise performance, and bandwidth against the source impedance before deployment, especially when the audio or communications path carries large DC offsets.
پیشنهادی
Power Converter Feedback Interface
INA143UA/2K5 is suitable for monitoring a small differential feedback voltage in a power-conversion or remote-sensing system. The selectable gain lets the designer attenuate or amplify the sensed error signal before comparison or ADC conversion, while the 5 V/us slew rate responds to changing operating conditions. The critical design checks are the power stage’s maximum differential input, allowable common-mode voltage, and the amplifier output range. Keep the feedback sense pair together, avoid sharing high-current paths, and use the manufacturer gain configuration to prevent unexpected loading of the sensed node.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای INA143UA/2K5 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | INA143U/2K5 | INA141UA/2K5 | INA155UA/2K5 | INA132U/2K5 | AD8278ARZ |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Product Type | Precision difference amplifier | Precision difference amplifier | Instrumentation amplifier | Difference amplifier | Difference amplifier | Difference amplifier |
تفاوتهای کلیدی
- Selectable gain in one precision difference amplifier (در مقابلINA141UA/2K5)
- High-speed precision signal capability (در مقابلINA132U/2K5)
- Documented common-mode rejection (در مقابلAD8278ARZ)
یادداشتهای طراحی
Route the two differential inputs as a compact, symmetric pair with minimal area and a continuous ground reference beneath the pair. Avoid switching-node copper, high-current return paths, and discontinuous plane transitions beneath the amplifier. Keep the input connection to the source short because parasitic resistance and inductance can reduce common-mode rejection and disturb the laser-trimmed gain network.
Do not assume that an 8-pin SOIC footprint guarantees functional interchangeability. Confirm the gain-network connections, input common-mode range, output swing, offset, slew rate, and supply limits for every replacement candidate. INA141UA/2K5 has fixed gain of 10 rather than the selectable 10 or 0.1 modes, so it cannot reproduce every INA143UA/2K5 configuration without circuit changes.
For current-sense and bridge-sensor inputs, use Kelvin routing from the shunt or sensor pads and place optional input filtering close to the amplifier. Verify that added resistance and capacitance do not upset settling or create unequal input impedances. The INA143UA/2K5 provides 5 V/us slew rate and 250 uV offset, but those specifications do not remove the need to control differential-node transients and source impedance.
Place supply bypassing close to the device and route it using a short, low-inductance path. Confirm the actual input common-mode voltage and output swing against the selected gain before finalizing the power architecture. A fast slew rate helps reproduce dynamic signals, but inadequate bypassing, grounding, or output-headroom checks can still cause instability, clipping, or incorrect measurements.
اطلاعات انطباق
Texas Instruments lists the INA143UA/2K5 as active. Explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals statements were not identified in the accessible product information.