LM258WYST - Dual 30V Automotive Op Amp, 1.1MHz | STMicroelectronics
MPN: LM258WYST ✓ فعالLM258WYST نمای کلی
A dual operational amplifier is a pair of independent voltage amplifiers on a single die, each with high open-loop gain, differential inputs and a single-ended output. Because both channels share one die and one package, a designer can build differential, summing or instrumentation stages with closely matched characteristics. In the analog signal chain the op amp sits below the application level and above the passive level: it conditions, buffers and amplifies signals coming from sensors, resistive dividers and transducers. The LM258WYST is characterized for operation from a single supply across a wide voltage range, which is why it is used on 12 V and 24 V automotive and industrial rails where a 5 V-only part cannot operate.
Key specifications include a 1.1 MHz gain-bandwidth product, a slew rate of 0.3 V/us, typical input offset voltage of 2 mV, input bias current of 20 nA and a quiescent supply current of roughly 0.7 mA per amplifier. The 30 V supply ceiling allows direct connection to 24 V industrial buses with headroom for transients, while the internally compensated architecture removes the need for external compensation capacitors. The MiniSO-8 package with 0.65 mm lead pitch places two amplifiers in a footprint smaller than one SOIC-8 package.
The internal design is a classic bipolar single-supply amplifier: a differential input pair drives a Darlington output stage that can source and sink output current, while the compensation network is integrated on chip so the amplifiers are unity-gain stable. Closed-loop behaviour is therefore set by the external feedback network, and the same part can be used as a voltage follower, an inverting or non-inverting gain stage, or a transimpedance amplifier. Common-mode and supply rejection in the 90 dB to 100 dB range keep the stage well behaved on noisy battery rails, and the 3 V to 30 V supply span allows the same board design to work from an auxiliary 5 V rail up to a 24 V bus.
Typical uses include 12 V automotive sensor signal conditioning, 24 V industrial control loops, current-loop receivers and buffered instrumentation inputs. The dual-channel configuration also suits differential sensing, where two amplifiers amplify the plus and minus sides of a bridge sensor, and threshold-style signal conditioning with pull-up resistors on the outputs.
Leave roughly 1.5 V of output headroom at the 30 V operating limit, and place a 100 nF bypass capacitor at the supply pin. Keep feedback resistors close to the amplifier pins, since parasitic capacitance in the feedback loop reduces stability at high closed-loop gain.
This page consolidates distributor availability, drop-in alternatives that share the same MiniSO-8 footprint, and practical design guidance for the LM258WYST. The comparison table, thermal and layout notes and selection guidance are intended to shorten bring-up time for engineers who need a dual 30 V amplifier that remains in active production.
جایگزینهای drop-in برای LM258WYST — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای LM258WYST (همان فرمفاکتور و فوتپرینت) — متفاوت در Amplifier Type, Package, Automotive Grade, Number of Circuits, Output Type.
LM2904YST
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM358YST
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
LM358WN
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
LM2904YDT
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM358YPT
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM258WYST حداکثر مقادیر مجاز و مشخصات الکتریکی
| Amplifier Type | Dual General Purpose Operational Amplifier |
| Number of Circuits | 2 (independent channels) |
| Gain-Bandwidth Product | 1.1 MHz |
| Maximum Supply Voltage | 30 V |
| Minimum Supply Voltage | 3 V |
| Slew Rate | 0.3 V/us |
| Input Offset Voltage | 2 mV typical |
| Input Bias Current | 20 nA typical |
| Input Resistance | 100 Mohm typical |
| Quiescent Supply Current | 0.7 mA per amplifier typical |
| Open Loop Gain | 100 dB typical |
| Common Mode Rejection Ratio | 90 dB typical |
| Supply Rejection Ratio | 100 dB typical |
| Output Swing | Rail-to-rail output swing capability |
| Compensation | Internally frequency-compensated, unity-gain stable |
| Automotive Grade | Yes, 30 V automotive-qualified family |
| بستهبندی | MiniSO-8 / 8-TSSOP, 0.65 mm pitch, 3.0 mm width |
| نوع نصب | Surface Mount |
| وضعیت RoHS | Compliant |
| Packaging | Tape and reel |
پیکربندی پین LM258WYST
| پین 1 | OUT1 — Channel 1 amplifier output |
| پین 2 | IN-1 — Channel 1 inverting input |
| پین 3 | IN+1 — Channel 1 non-inverting input |
| پین 4 | GND — Negative supply / ground |
| پین 5 | IN+2 — Channel 2 non-inverting input |
| پین 6 | IN-2 — Channel 2 inverting input |
| پین 7 | OUT2 — Channel 2 amplifier output |
| پین 8 | VCC — Positive supply input |
کاربردهای معمول
LM258WYST مناسب است برای 6 کاربردs: 12V Automotive Sensor Signal Conditioning, 24V Industrial Control Loops, Differential Bridge Sensor Amplification, Current Loop Receiver and Transmitter Buffer, Audio and Headphone Output Buffering, Battery Monitoring and Protection Front End.
12V Automotive Sensor Signal Conditioning
The LM258WYST is a natural fit for 12 V automotive sensor conditioning because its 30 V maximum supply rating lets both amplifier channels sit directly on the vehicle battery rail without a separate regulator or level shifter. With 1.1 MHz gain-bandwidth product and 0.3 V/us slew rate it handles slow to medium-rate sensor signals, and the millivolt-level input offset voltage keeps the error small relative to typical 0.5 V to 5 V sensor outputs. The automotive qualification of the LM258 family suits body, chassis and powertrain peripherals, while the 8-pin MiniSO-8 package keeps the footprint small for dense harness-side electronics.
پیشنهادی
24V Industrial Control Loops
In 24 V industrial control cabinets the LM258WYST removes the need for a 5 V front end, because the same amplifier can be powered directly from the 24 V bus up to its 30 V ceiling. That saves a regulator stage, reduces board area and improves transient immunity on noisy machine rails, where the 100 dB typical supply rejection ratio helps keep the loop stable. Two independent channels per package allow a single dual part to handle both a feedback amplifier and an error amplifier, and the 1.1 MHz gain-bandwidth product is more than adequate for process control loops in the kilohertz range.
پیشنهادی
Differential Bridge Sensor Amplification
The dual configuration of the LM258WYST is ideal for bridge-based sensing, where one channel buffers the positive excitation side and the other the negative side, cancelling common-mode error directly in the signal path. Because both amplifiers come from the same die, their offset voltage and bias current track closely, which improves differential accuracy compared with two unrelated parts. The high input resistance of roughly 100 Mohm loads the bridge only lightly, and the internal frequency compensation makes the stage unity-gain stable for direct buffer use with no external compensation capacitor.
پیشنهادی
Current Loop Receiver and Transmitter Buffer
The LM258WYST works well as the front end of a 4-20 mA current-loop receiver, where the amplifier buffers the sense resistor voltage and drives the transmitter stage toward the 24 V line supply. Its 30 V operating ceiling matches the industrial loop voltage, and the roughly 0.7 mA per-amplifier quiescent draw keeps loop power budget low, which matters for loop-powered field transmitters. The 1.1 MHz bandwidth provides ample loop gain for loop shaping, and the rail-to-rail output swing capability keeps the output useful across the loop resistance range.
پیشنهادی
Audio and Headphone Output Buffering
The LM258WYST can buffer headphone and line-level audio outputs in equipment that runs from a single supply of 12 V or 24 V, where a 5 V-only dual amplifier would be over-stressed. Its 1.1 MHz gain-bandwidth product is more than sufficient for 20 kHz audio content, and the low quiescent current of about 0.7 mA per amplifier suits battery-powered portable audio gear that must also survive a wide supply range. The rail-to-rail output swing capability maximizes usable output level into headphone impedances without a boost stage.
پیشنهادی
Battery Monitoring and Protection Front End
In battery packs and power-management boards, the LM258WYST amplifies cell-monitor taps and drives the comparison stage that protects against over-charge and over-discharge. Its wide 3 V to 30 V operating span means the same amplifier handles both a 3 V cell sense line and a 24 V bus sense line, and the automotive qualification matches the harsh thermal environment inside a pack enclosure. Two channels per package support dual-polarity sensing, and the 0.7 mA quiescent draw per amplifier avoids loading the very supply it is monitoring.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای LM258WYST — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | LM2904YST | LM358YST | LM358WN | LM2904Y | LM358Y |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | MiniSO-8 (8-TSSOP), 0.65 mm pitch | MiniSO-8 (8-TSSOP) - same footprint | MiniSO-8 (8-TSSOP) - same footprint | MiniSO-8 (8-TSSOP) - same footprint | MiniSO-8 (8-TSSOP) - same footprint | MiniSO-8 (8-TSSOP) - same footprint |
| Number of Amplifiers | 2 independent channels | 2 independent channels | 2 independent channels | 2 independent channels | 2 independent channels | 2 independent channels |
| Gain-Bandwidth Product | 1.1 MHz | 1.1 MHz | 1.1 MHz | 1.1 MHz | 1.1 MHz | 1.1 MHz |
| Automotive Grade | Yes (30 V automotive-qualified family) | Industrial and automotive control positioning | General purpose, not automotive qualified | General purpose | Automotive/industrial positioning | General purpose |
| Compensation | Internally frequency-compensated, unity-gain stable | Internally frequency-compensated | Internally frequency-compensated | Internally frequency-compensated | Internally frequency-compensated | Internally frequency-compensated |
| Supply Current | 1.1 MHz GBW, 0.3 V/us slew rate, 30 V supply | 1.1 MHz GBW, 30 V supply | 1.1 MHz GBW, lower supply class | 1.1 MHz GBW, lower supply class | 1.1 MHz GBW, 30 V supply | 1.1 MHz GBW, lower supply class |
| Order Code / Packaging | LM258WYST - tape and reel, 8-TSSOP | Tape and reel, 8-TSSOP | Tape and reel, 8-TSSOP | Tape and reel, 8-TSSOP | Base ordering code, 8-TSSOP | Base ordering code, 8-TSSOP |
تفاوتهای کلیدی
- Operates directly on 24 V industrial and 12 V automotive rails (در مقابلLM358YST)
- Two independent amplifiers in a 0.65 mm pitch MiniSO-8 footprint (در مقابلLM358WN)
- Automotive-qualified grade with the same electrical core (در مقابلLM2904YST)
- Same 1.1 MHz performance as family members with a lower supply ceiling (در مقابلLM358Y)
یادداشتهای طراحی
Do not assume the output can sit exactly on the supply rail. The bipolar output stage of the LM258 family needs roughly 1.5 V of headroom at the 30 V supply limit and about 2 V at the low end of the supply range, so a design that asks for a 0 V output on a 3 V supply will clip. Check the output swing spec in the STMicroelectronics LM258 datasheet against your required output range, and keep the load current within the amplifier's rated drive capability when the output sits close to the rail.
Place a 100 nF bypass capacitor directly at the VCC pin (pin 8) and connect it to the ground plane with a very short via, since the supply pin is shared by both channels and any supply impedance shows up as added noise in both amplifier outputs. Keep the ground connection of the two channels on the same solid ground plane, avoid routing feedback traces between the input and output pins of the same channel, and place feedback resistors within a few millimetres of the input pins to minimise parasitic capacitance effects on stability at higher closed-loop gains.
Estimated: with a 24 V supply, a 5 V output and 10 mA of load current per channel, each amplifier dissipates about 0.19 W, and 0.38 W for both channels of the package. In the MiniSO-8 outline this is manageable with normal copper pour at ambient temperatures up to about 85 C, but at higher ambient or higher channel current add a thermal relief and copper area around the pins. Verify junction temperature against the worst-case case: 24 V supply, minimum load resistance and maximum ambient.
Because the compensation is internal, the LM258WYST is unity-gain stable, but closed-loop gain still sets the usable bandwidth through the feedback network. On a 24 V bus with switch noise, add an input RC filter (for example 1 kohm plus 100 nF) ahead of the non-inverting pin if the source impedance is high, and keep the input common-mode voltage within the amplifier's common-mode range. For differential bridge inputs, drive both channels from matched networks so the common-mode rejection advantage of the matched die is preserved.
اطلاعات انطباق
The LM258 family is the automotive-qualified 30 V member of the ST dual general-purpose amplifier family; RoHS compliance is indicated by the manufacturer listing. REACH, halogen-free status and conflict-minerals declarations should be confirmed against the current STMicroelectronics material declaration for the specific order code.