LM2902MX-ON - Quad General-Purpose Op Amp | onsemi
MPN: LM2902MX-ON ✓ فعالLM2902MX-ON نمای کلی
An operational amplifier, commonly called an op amp, is an analog IC that amplifies the voltage difference between its inverting and non-inverting inputs. The LM2902MX-ON combines four amplifiers in one package, reducing component count and simplifying PCB layout compared with four separate single-amplifier packages. Within the semiconductor hierarchy, it is a quad operational amplifier, a type of analog amplifier and signal-conditioning IC.
The primary feature of this device is its four-channel architecture within a 14-pin package. The LM2902MX family is associated with supply operation extending to ±16 V or 32 V total, covering conventional single-supply and dual-supply industrial circuit environments. The onsemi LM2902MX listing identifies the device as a standard general-purpose amplifier with four circuits in a 14-pin SOP package.
As a general-purpose quad amplifier, the LM2902MX-ON can implement four common analog functions on one board. Individual channels may be used as non-inverting or inverting amplifiers, buffers, comparators, or active filters when operated within their electrical limits. Because each channel shares the same package, bypassing, and supply connections, designers should pay particular attention to power-supply decoupling and channel-to-channel feedback isolation.
Typical applications include industrial sensor conditioning, instrumentation, analog measurement systems, control loops, and general PCB signal amplification. The four-channel organization is especially useful when a board requires several similar low-frequency signal-processing stages. In such designs, the device can reduce footprint requirements while simplifying assembly compared with four separate single op-amp packages.
A key design consideration is decoupling. Place a supply bypass capacitor close to the device supply pins and keep input and output routing short to reduce noise pickup and unstable feedback behavior. Load capacitance, output-current demand, common-mode range, and supply sequencing must also be checked against the manufacturer's operating limits before the amplifier is used in a new circuit.
This product page combines the confirmed LM2902MX-ON device identity with package-level information, verified substitute references, practical circuit guidance, and engineering-oriented comparisons. It helps designers determine whether a candidate has the required four-channel, 14-pin architecture and helps narrow the next step to electrical verification using the manufacturer datasheet.
جایگزینهای drop-in برای LM2902MX-ON — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای LM2902MX-ON (همان فرمفاکتور و فوتپرینت) — متفاوت در Package, Number of Amplifier Channels, Product Type, Channel Architecture, Frequency Compensation.
LM2902MX/NOPB
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM2902MX
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM2902MX
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM2902M
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM2902DTB
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM2902MX-ON حداکثر مقادیر مجاز و مشخصات الکتریکی
| Product Type | General-purpose operational amplifier |
| Number of Amplifier Channels | 4 circuits |
| Channel Architecture | Quad |
| بستهبندی | 14-pin SOP |
| تعداد پینها | 14 pins |
| نوع نصب | Surface mount |
| ولتاژ تغذیه | ±16 V or 32 V |
پیکربندی پین LM2902MX-ON
| پین 1 | OUT1 — Output of amplifier 1 |
| پین 2 | IN1- — Inverting input of amplifier 1 |
| پین 3 | IN1+ — Non-inverting input of amplifier 1 |
| پین 4 | V+ — Positive supply connection |
| پین 5 | IN2+ — Non-inverting input of amplifier 2 |
| پین 6 | IN2- — Inverting input of amplifier 2 |
| پین 7 | OUT2 — Output of amplifier 2 |
| پین 8 | OUT3 — Output of amplifier 3 |
| پین 9 | IN3- — Inverting input of amplifier 3 |
| پین 10 | IN3+ — Non-inverting input of amplifier 3 |
| پین 11 | V- — Negative supply connection |
| پین 12 | IN4+ — Non-inverting input of amplifier 4 |
| پین 13 | IN4- — Inverting input of amplifier 4 |
| پین 14 | OUT4 — Output of amplifier 4 |
کاربردهای معمول
LM2902MX-ON مناسب است برای 6 کاربردs: Industrial Sensor Conditioning, Analog Instrumentation, Power Supply Feedback Control, Active Filter and Buffering, Audio and Communication Conditioning, Embedded Control and Data Acquisition.
Industrial Sensor Conditioning
The LM2902MX-ON fits four-channel sensor-conditioning circuits because its package contains four general-purpose operational-amplifier circuits in a 14-pin SOP package. Individual channels can amplify low-level sensor signals, buffer inputs for an analog-to-digital converter, or form active gain stages. The consolidated package reduces board area compared with four separate single-amplifier devices. According to onsemi product information, the LM2902MX family is intended for general-purpose instrumentation and is listed for operation up to ±16 V or 32 V total supply. Confirm the exact input common-mode range, output swing, offset voltage, bandwidth, and temperature limits in the manufacturer datasheet before defining the gain and signal levels.
پیشنهادی
Analog Instrumentation
The LM2902MX-ON is suitable for multi-channel analog instrumentation where several precision signal paths must be implemented with one IC. Four amplifiers can handle input buffering, differential-to-single-ended conversion, gain stages, and active filters on the same board. The onsemi LM2902MX listing identifies the device as a standard general-purpose amplifier with four circuits in a 14-pin package. The single-package approach can simplify routing and procurement when all channels use similar supply and grounding arrangements. Engineers should still evaluate offset, input-bias-current drift, noise, slew rate, and output-capacitance stability for the intended instrumentation gain and bandwidth.
پیشنهادی
Power Supply Feedback Control
The LM2902MX-ON can support power-supply feedback and error-amplifier functions in designs requiring more than one control path. Its four channels allow a feedback amplifier, current-sense amplifier, and auxiliary monitoring stage to share one package. The LM2902MX family is listed for supply operation extending to ±16 V or 32 V total, making the family applicable to conventional industrial supply rails when its exact operating limits are met. The benefit is fewer packages and shorter feedback routing, but loop compensation and stability must be analyzed per channel. Verify the common-mode input range, output-drive capability, slew rate, and saturation behavior at the actual error-amplifier output level.
پیشنهادی
Active Filter and Buffering
The LM2902MX-ON can implement several active-filter or buffer functions when a board requires multiple low-frequency analog stages. A single 14-pin quad package provides four channels for sections of a multi-stage filter, impedance buffering, or gain normalization. The four-channel architecture can reduce PCB area and keep related stages within one common package. The onsemi LM2902MX family listing identifies a standard general-purpose amplifier, but does not by itself establish a particular noise, slew-rate, or stability margin. Check the manufacturer datasheet for the gain-bandwidth product, output-capacitance limits, input bias current, and recommended compensation before selecting component values for a filter with high Q or long settling time.
پیشنهادی
Audio and Communication Conditioning
The LM2902MX-ON can be used for low-frequency audio or communication-signal conditioning when four similar channels are required. Possible uses include microphone preamplifier stages, line-level buffers, gain controls, and output drivers within the device's electrical limits. Its four general-purpose channels in one 14-pin SOP package can reduce the footprint compared with separate single amplifiers. The onsemi LM2902MX listing supports its use in general-purpose instrumentation, while the associated LM2902MX family listing identifies operation up to ±16 V or 32 V total supply. For audio paths, evaluate output distortion, noise, slew rate, load capability, and stable operation with the intended coupling network rather than assuming suitability from the four-channel description alone.
پیشنهادی
Embedded Control and Data Acquisition
The LM2902MX-ON is applicable around embedded controllers and data-acquisition boards where analog sensor outputs must be amplified, inverted, or buffered before conversion. Four channels can provide local conditioning close to the sensor connector, reducing sensitive-signal trace length when the layout is planned carefully. The onsemi LM2902MX listing identifies a four-circuit general-purpose amplifier in a 14-pin SOP package. Because the package contains four amplifiers but a shared supply, system planning must include startup behavior, supply-noise coupling, and the maximum simultaneous output current. Confirm rail-to-rail behavior, input range, output swing, and absolute maximum ratings in the exact onsemi datasheet before using it with an ADC or controller input.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای LM2902MX-ON — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | LM2902MX/NOPB | LM2902MX | LM2902MX | LM2902M | LM2902DT |
|---|---|---|---|---|---|---|
| Manufacturer | onsemi | Texas Instruments | ROHM Semiconductor | Fairchild Semiconductor | onsemi | onsemi |
| Package | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 |
| Amplifier Channels | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Product Classification | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier |
| Number of Pins | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins |
| Pin and Terminal Compatibility | 14-pin LM2902 footprint | 14-pin LM2902 footprint | 14-pin LM2902 footprint | 14-pin LM2902 footprint | Consistent terminals and package | Identical primary performance profile |
| Parameter Match to LM2902MX-ON | Reference part | 100% structural match | 100% structural match | 100% structural match | 100% functional and package match | 100% matched primary parameters |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
تفاوتهای کلیدی
- Four general-purpose channels in one 14-pin package (در مقابلLM2902MX/NOPB)
- Direct onsemi ordering-code continuity (در مقابلLM2902MX/NOPB)
- Documented terminal and package consistency (در مقابلLM2902M)
- Identical compared primary performance profile (در مقابلLM2902DT)
یادداشتهای طراحی
Place the main supply bypass capacitor immediately between the V+ and V- pins, and add additional local decoupling where multiple analog channels drive changing loads. The LM2902MX family is listed for operation up to ±16 V or 32 V total, but the supply design must remain within the exact datasheet limits. Avoid routing high-current return paths beneath the amplifier ground pins and use a quiet return plane to reduce channel-to-channel supply coupling.
Keep each non-inverting input, inverting input, and output trace as short as practical, especially when the channel handles a high-gain or high-impedance signal. Place resistor networks and compensation components close to their associated pins rather than distributing them around the package. Because all four amplifiers share one package and supply, maintain adequate spacing between high-current output paths and sensitive input routing to minimize parasitic pickup.
Do not treat every LM2902 suffix as automatically interchangeable. Confirm the manufacturer, temperature grade, pin arrangement, supply limits, offset voltage, input-bias current, output swing, and package drawing for the exact ordering code. The LM2902MX/NOPB, ROHM LM2902MX, and Fairchild LM2902MX all use the same base designation but belong to different manufacturers, so approved-source and electrical review remain necessary before substitution.
Analyze gain-bandwidth, slew-rate, output-capacitance, and stability requirements for each independently wired channel. Large capacitive loads can produce ringing or instability even when the device is used at a modest nominal gain. For instrumentation and audio paths, check noise, distortion, input bias current, and output-drive behavior at the actual source impedance and load. Decoupling and short feedback paths should be evaluated together rather than treated as separate fixes.
اطلاعات انطباق
The LM2902MX-ON is a general-purpose operational amplifier rather than an automotive-qualified device. No RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was confirmed for the exact ordering code.