LM324KADR - Quad 30V 1.2MHz Op Amp | Texas Instruments
MPN: LM324KADR ✓ فعالLM324KADR نمای کلی
An operational amplifier is a high-gain differential amplifier whose external feedback network determines its behavior. In the signal-chain hierarchy, the LM324KADR belongs to the operational-amplifier family within amplifier ICs and analog signal-chain devices. Unlike a single-amplifier package, this quad device integrates four independent amplifiers, allowing one component to support multiple analog channels while reducing package count and board area.
Key features include four independent amplifiers, operation from a single supply or split supplies, a 1.2 MHz gain-bandwidth product, and a 3 mV input offset voltage. The 14-pin SOIC package also provides improved 2 kV ESD protection. These characteristics make the LM324KADR appropriate for low-frequency control loops, sensor amplification, buffering, and general-purpose signal processing where a broad supply-voltage range and economical quad integration are more important than precision or high-speed performance.
The amplifiers are internally frequency compensated, which simplifies closed-loop design when stable operation is required. The 30 V maximum supply supports higher-voltage industrial interfaces than many low-voltage rail-to-rail amplifier families. Split-supply operation is also possible when the difference between the supplies remains within the device's permitted range. Its 1.2 MHz bandwidth is adequate for audio-band and general control applications but is not intended for high-speed instrumentation or RF signal paths.
Typical uses include 4–20 mA current-loop receivers, industrial sensor interfaces, active low-pass filters, audio preamplifier stages, relay and motor-control loops, and general instrumentation. Using four amplifiers in one SOIC package simplifies multi-channel designs, although each amplifier has an independent signal path and shares the common supply and ground pins.
PCB design should keep sensitive input and feedback traces short, place input bypassing close to the supply pins, and maintain a stable ground reference around the device. Do not substitute a rail-to-rail amplifier without checking input common-mode range, output swing, offset voltage, bandwidth, stability, and maximum supply voltage; those electrical differences can change the behavior of an existing LM324-based circuit.
جایگزینهای drop-in برای LM324KADR — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای LM324KADR (همان فرمفاکتور و فوتپرینت) — متفاوت در Package, Operating Temperature Range, Supply Configuration, Amplifier Type, Input Offset Voltage.
LM324ADR
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM324ADG
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM324ADBR
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM324KNSR
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM324ANSR
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM324KADR حداکثر مقادیر مجاز و مشخصات الکتریکی
| Amplifier Type | Quad general-purpose operational amplifier |
| Number of Amplifiers | 4 circuits |
| Maximum Supply Voltage | 30 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Input Offset Voltage | 3 mV |
| ESD Withstand | 2 kV |
| محدوده دمای کاری | 0 °C to 70 °C |
| بستهبندی | SOIC-14 (D), 14 pins |
| نوع نصب | Surface mount |
| Supply Configuration | Single supply or split supply |
| Frequency Compensation | Internal |
پیکربندی پین LM324KADR
| پین 1 | OUT1 — Output of amplifier 1 |
| پین 2 | IN1- — Inverting input of amplifier 1 |
| پین 3 | IN1+ — Non-inverting input of amplifier 1 |
| پین 4 | V- — Negative supply connection |
| پین 5 | IN2+ — Non-inverting input of amplifier 2 |
| پین 6 | IN2- — Inverting input of amplifier 2 |
| پین 7 | OUT2 — Output of amplifier 2 |
| پین 8 | OUT3 — Output of amplifier 3 |
| پین 9 | IN3- — Inverting input of amplifier 3 |
| پین 10 | IN3+ — Non-inverting input of amplifier 3 |
| پین 11 | V+ — Positive supply connection |
| پین 12 | IN4+ — Non-inverting input of amplifier 4 |
| پین 13 | IN4- — Inverting input of amplifier 4 |
| پین 14 | OUT4 — Output of amplifier 4 |
کاربردهای معمول
LM324KADR مناسب است برای 6 کاربردs: Industrial 4–20 mA Sensor Interface, Sensor Signal Conditioning, Audio Preamplifier Stages, Active Filter and Control Loops, Power Supply Feedback and Monitoring, Relay and Motor Control Interfaces.
Industrial 4–20 mA Sensor Interface
The LM324KADR fits a 4–20 mA receiver when the design needs four general-purpose amplifiers, operation from a broad supply range, and a common 14-pin SOIC footprint. One channel can buffer the signal produced by a precision current-to-voltage converter, while other channels provide active filtering, gain, or diagnostics. Its 1.2 MHz gain-bandwidth product is ample for the bandwidth normally associated with process-control loops, and the 30 V maximum supply provides margin for industrial interface voltages. However, the input common-mode range, output swing, offset voltage, and channel-to-channel matching must remain inside the actual supply-rail conditions because the LM324KADR is not universally rail-to-rail.
پیشنهادی
Sensor Signal Conditioning
The four independent amplifiers in the LM324KADR allow a compact analog front end to amplify, filter, and buffer outputs from resistive, capacitive, or voltage-based sensors. A 1.2 MHz gain-bandwidth product supports low-frequency control and instrumentation stages, while the internally compensated architecture simplifies implementation of ordinary closed-loop gain configurations. The 3 mV nominal input offset specification should be included in the error budget when the sensor signal is small. For bridge or high-impedance sensors, input bias current and common-mode limits must be checked because the general-purpose LM324 architecture is not optimized for extremely low bias current or rail-to-rail sensing.
پیشنهادی
Audio Preamplifier Stages
The LM324KADR can implement general-purpose audio preamplifier, mixer, and buffer stages where a four-amplifier package reduces component count. Its 1.2 MHz gain-bandwidth product provides more bandwidth than the audio band, and the 30 V maximum supply supports higher-amplitude headroom when operating from split supplies. The nominal 3 mV input offset can appear as low-level distortion or channel imbalance in high-gain audio paths, so designers should consider the signal level, source impedance, and required noise performance. Stable feedback-network values and adequate output-current margin are necessary to avoid distortion at the limits of the amplifier's drive capability.
پیشنهادی
Active Filter and Control Loops
The LM324KADR is well suited to active low-pass filters, integrators, comparators, and servo-control loops built with passive feedback networks. Its internal frequency compensation simplifies the design of stable closed-loop amplifiers, while four independent channels allow one package to form several filter poles or separate control functions. The 1.2 MHz gain-bandwidth product gives useful margin over low-frequency control loops, but loop-gain and phase-margin calculations remain necessary when operating close to the amplifier's bandwidth limit. Component tolerances, input/output swing, and the 3 mV nominal offset directly influence cutoff frequency, DC error, and useful signal range.
پیشنهادی
Power Supply Feedback and Monitoring
Within a linear power-supply or monitoring subsystem, the LM324KADR can supervise an output, amplify a feedback error signal, or provide buffering for a comparator-based protection circuit. Its ability to operate from a broad supply range and split supplies is useful when the monitored rail is referenced to a higher-voltage system, while the four-channel package leaves spare amplifiers for redundant monitoring or filtering. The 30 V maximum supply rating is the principal design boundary; input and output common-mode limits must still be respected. Offset error, output swing, and stability near the output rail should be evaluated against the required protection threshold.
پیشنهادی
Relay and Motor Control Interfaces
The LM324KADR can amplify error signals and drive transistor stages in relay, solenoid, or motor-control interfaces when the system operates from a conventional industrial supply. Four amplifiers permit integration of command amplification, current sensing, feedback filtering, and output-enable logic without using four separate packages. The 1.2 MHz gain-bandwidth product is normally sufficient for slower closed-loop control systems, although inductive loads require external flyback protection and care to prevent output saturation during switching transients. Because the device is not a power driver, verify output-current capability, output swing, thermal dissipation, and the external transistor dissipation separately.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای LM324KADR — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | LM324ADR | LM324ADG | LM324ADBR | LM324KNSR | LM324ANSR |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SOIC-14 (D) | SOIC-14 (D) | SOIC-14 (D) | SOIC-14 (D) | SOIC-14 (D) | SOIC-14 (D) |
| Amplifier Configuration | Quad | Quad | Quad | Quad | Quad | Quad |
| Number of Pins | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins |
تفاوتهای کلیدی
- K-series identification emphasizes improved ESD protection (در مقابلLM324ADR)
- Four independent amplifiers in a 14-pin SOIC (در مقابلLM324ADG)
- Broad supply capability for industrial interfaces (در مقابلLM324ANSR)
یادداشتهای طراحی
Do not assume rail-to-rail input or output behavior. Before finalizing a single- or split-supply circuit, verify the input common-mode range and output swing at the actual supply voltage, especially when a sensor output can approach either rail. Also confirm that the selected replacement MPN has the same 14-pin pinout and that its offset, temperature, and ESD ratings satisfy the design rather than relying only on the LM324 family name.
Place the supply bypass capacitor close to pins 4 and 11, and keep each channel's input and feedback components close to its corresponding pins. Route output traces away from high-impedance input nodes to reduce capacitive feedthrough. The four amplifier sections share common power and ground pins, so adequate decoupling and a low-impedance ground plane are particularly important when several channels switch or drive appreciable loads simultaneously.
Estimated: amplifier dissipation is approximately equal to (V+ - VOUT) multiplied by output current for the relevant channel. For example, using a 30 V supply, a 12 V output, and 20 mA gives an estimated 0.36 W per active channel before accounting for the other internal dissipation. Use the manufacturer electrical and thermal limits for final design verification, and ensure the SOIC copper area and ambient temperature can dissipate the calculated load.
اطلاعات انطباق
The verified product information does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. The device is an industrial-temperature amplifier rather than an automotive-qualified option, so AEC-Q100 is recorded as not applicable.