LPC1754FBD80 - 100MHz Cortex-M3 MCU with USB | NXP
MPN: LPC1754FBD80 ✓ فعالLPC1754FBD80 نمای کلی
A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The ARM Cortex-M3 core provides a 32-bit instruction set and efficient event-driven execution suitable for industrial control, communications, and connected equipment. Within the product hierarchy, the LPC1754FBD80 is an ARM Cortex-M3 MCU, then a 32-bit microcontroller, and finally a general-purpose embedded processor.
The LPC1754FBD80 includes 128 KB of flash for firmware and 32 KB of SRAM for working data. Its integrated USB interface supports designs that need USB connectivity without adding a separate host controller. Additional LPC1700-family peripherals include Ethernet, USB 2.0 host, OTG, device, and CAN 2.0B support at the family level. These interfaces reduce the component count in industrial gateways, USB equipment, and communication controllers.
The 100 MHz Cortex-M3 core supports computationally intensive control loops and responsive protocol handling while retaining the deterministic behavior expected from embedded software. The device operates from 2.5 V or 3.3 V supply rails, allowing integration with common industrial and consumer logic levels. Its 80-pin LQFP package provides enough external connectivity for buses, sensors, communications, and mixed-signal interfaces.
Typical applications include USB-enabled test equipment, industrial data acquisition, CAN-connected factory systems, Ethernet gateways, and compact embedded controllers. Designers can use the USB device interface for configuration and diagnostics, Ethernet for network connectivity, and CAN for robust industrial communications. Firmware development follows the standard ARM Cortex-M3 ecosystem, including startup code, linker configuration, debugging, and peripheral drivers.
PCB implementation requires careful attention to the 80-pin footprint, exposed ground and supply connections, and the device's decoupling requirements. Place bulk and high-frequency bypass capacitors close to their associated power pins, route clock and high-speed USB signals away from noisy sources, and verify signal integrity and power sequencing in the final layout.
This product page combines the NXP device identity and package information with cross-reference analysis and practical design guidance. It also distinguishes exact drop-in candidates from ordering-code variants so engineers can evaluate replacements without confusing mechanical compatibility with functional qualification.
جایگزینهای drop-in برای LPC1754FBD80 — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای LPC1754FBD80 (همان فرمفاکتور و فوتپرینت) — متفاوت در Package.
LPC1754FBD80K
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LPC1754FBD80 حداکثر مقادیر مجاز و مشخصات الکتریکی
| Product Type | 32-bit ARM Cortex-M3 microcontroller |
| Maximum CPU Frequency | 100 MHz |
| Flash Memory | 128 KB |
| SRAM | 32 KB |
| Core Architecture | ARM Cortex-M3 |
| ولتاژ تغذیه کاری | 2.5 V or 3.3 V |
| بستهبندی | 80-pin LQFP, 12 mm x 12 mm |
| نوع نصب | Surface mount |
| Integrated USB | Yes, USB 2.0 device, host, and OTG support |
| Ethernet Support | Yes, LPC1700-family Ethernet support |
| CAN Support | Yes, CAN 2.0B family support |
راهنمای پیکربندی پین LPC1754FBD80 80-pin lqfp, 12 mm x 12 mm
پیکربندی پین برای LPC1754FBD80 (پکیج 80-pin lqfp, 12 mm x 12 mm). این IC دیجیتال شامل GPIO، رابطهای ارتباطی (UART، SPI، I2C) و پینهای تغذیه است. برای عملکردهای جایگزین پین و گزینههای پیکربندی به دیتاشیت سازنده مراجعه کنید. ضروری برای طراحی سیستمهای نهفته و چیدمان PCB.
داده پینآوت تفصیلی موجود نیست برای LPC1754FBD80.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
LPC1754FBD80 مناسب است برای 6 کاربردs: USB-Enabled Industrial Control, USB Test and Measurement Instrument, CAN-Connected Factory Gateway, Ethernet and USB Communications Hub, Portable Data-Acquisition Controller, Embedded Security and Access Controller.
USB-Enabled Industrial Control
The LPC1754FBD80 fits industrial controllers that combine a 100 MHz control loop with USB service connectivity. Its 128 KB flash stores application firmware, monitoring logic, and USB descriptors, while 32 KB SRAM supports real-time state, buffers, and protocol handling. The device can execute control tasks while exposing configuration, diagnostics, or logged data through a USB device interface. Place the USB transceiver and its specified protection network near the connector, keep the data path away from switching power nodes, and follow the manufacturer layout guidance for decoupling and signal return. The 2.5 V or 3.3 V operating options also permit integration with common industrial logic levels, although external isolation and level translation remain necessary where field-side interfaces require them.
پیشنهادی
USB Test and Measurement Instrument
The LPC1754FBD80 is appropriate for compact measurement instruments that use USB as a control and data interface. Its 100 MHz ARM Cortex-M3 core provides sufficient throughput for acquisition sequencing, calibration, status processing, and USB command handling, while 128 KB flash accommodates firmware and configuration data. The integrated USB capability helps reduce external interface overhead compared with a design using a separate USB controller. For instruments with Ethernet connectivity, an Ethernet transceiver can be paired with the MCU's LPC1700-family Ethernet support. Validate analog isolation, grounding, connector protection, and USB enumeration behavior in the final measurement architecture rather than treating the MCU as a substitute for signal-conditioning hardware.
پیشنهادی
CAN-Connected Factory Gateway
The LPC1754FBD80 supports factory gateways that bridge CAN equipment to a central network or service interface. The Cortex-M3 core can process CAN traffic, maintain device state, and run communication protocols at 100 MHz, while the 128 KB flash provides space for gateway firmware and update logic. Use the LPC1700-family CAN capability with a suitable transceiver such as the TJA1057, and reserve the Ethernet or USB interface for configuration, diagnostics, or upstream connectivity. Power-system design should include transient protection and filtering appropriate to industrial wiring. Validate bit timing, bus termination, isolation strategy, and error recovery against the CAN 2.0B implementation described in the NXP documentation.
پیشنهادی
Ethernet and USB Communications Hub
The LPC1754FBD80 is suited to embedded communications equipment that presents a local USB interface while also supporting the Ethernet capabilities of the LPC1700 family. The 100 MHz processor can supervise protocol processing and traffic management, and the 128 KB flash supports networking firmware, configuration storage, and service code. A physical-layer device such as KSZ8041 or LAN7500 can implement the Ethernet copper interface where the required clocks, magnetics, and signal conditioning are appropriately designed. USB and Ethernet paths should be routed as controlled-impedance interfaces, with ESD protection placed near external connectors. Validate boot ordering, firmware update mechanisms, thermal performance in enclosed equipment, and Ethernet compliance against the selected companion devices.
پیشنهادی
Portable Data-Acquisition Controller
The LPC1754FBD80 can serve as the control center of a compact portable data-acquisition unit. Its 100 MHz core supports sensor timing, filtering, sampling control, and real-time data preparation, while 32 KB SRAM accommodates working buffers for shorter acquisition bursts. Firmware and configuration can occupy the 128 KB flash, and USB provides a convenient connection for configuration and data transfer. The device's 2.5 V or 3.3 V supply options simplify integration with mixed-signal designs, although low-noise analog circuitry may require separate regulation. Validate sensor settling, isolation requirements, acquisition latency, thermal drift, and USB full-speed or high-speed topology against the external signal chain and enclosure conditions.
پیشنهادی
Embedded Security and Access Controller
The LPC1754FBD80 fits embedded access-control equipment that performs protocol handling, local decisions, status reporting, and USB service functions. Its 100 MHz Cortex-M3 core has ample performance for state-machine processing and communication tasks, and 128 KB flash can store control firmware and fixed configuration. The LPC1700 peripheral set can support Ethernet or CAN links when the system requires remote administration or bus interoperability. Keep credential storage, key material, and any production secret outside ordinary firmware wherever possible, and use the device's security features only as defined by the manufacturer documentation. Validate lockout behavior, update rollback policy, physical tamper response, and watchdog recovery before deployment in access-control applications.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای LPC1754FBD80 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | LPC1754FBD80K |
|---|---|---|
| Package | 80-pin LQFP | 80-pin LQFP |
| Brand | NXP Semiconductors | NXP Semiconductors |
| CPU Core | ARM Cortex-M3 | ARM Cortex-M3 |
| Maximum CPU Frequency | 100 MHz | 100 MHz |
| Flash Memory | 128 KB | 128 KB |
| SRAM | 32 KB | 32 KB |
| Operating Supply Voltage | 2.5 V or 3.3 V | 2.5 V or 3.3 V |
| USB Connectivity | Integrated USB | Integrated USB |
| Communications Peripherals | Ethernet and CAN 2.0B family support | Ethernet and CAN 2.0B family support |
| Ordering Attribute | Base LPC1754FBD80 ordering code | K-suffixed ordering code; confirm exact manufacturer ordering attributes |
تفاوتهای کلیدی
- Provides the full 100 MHz Cortex-M3 configuration in the same 80-pin LQFP footprint (در مقابلLPC1754FBD80K)
- Integrates USB with substantial local memory (در مقابلLPC1754FBD80K)
- Supports industrial communication connectivity in one microcontroller (در مقابلLPC1754FBD80K)
یادداشتهای طراحی
Plan the 2.5 V or 3.3 V supply with the decoupling arrangement and voltage tolerances specified by NXP. Place bulk capacitance near the entry point and high-frequency bypass capacitors adjacent to the relevant device supply pins. Keep USB transceiver, Ethernet physical-layer, and transceiver return currents away from sensitive analog return paths. If the board also powers motors, relays, or actuators, isolate those noisy loads so their switching transients do not propagate into the microcontroller rail.
Use the manufacturer LQFP80 land pattern and pin-description table rather than a generic 80-pin symbol. Maintain short, continuous return paths beneath high-frequency interfaces and observe the specified USB trace geometry. ESD protection should be close to the external connector, while common-mode chokes or other impedance-control devices should be selected according to the actual connector and cable environment. Review courtyard, solder mask, and assembly clearance before releasing the footprint.
Do not treat LPC1754FBD80, LPC1754FBD80K, LPC1754FBD80,551, and LPC1754FBD80,518 as automatically interchangeable. Ordering-code suffixes may distinguish temperature grade, packing form, or customer-facing order conventions. Compare the complete NXP ordering information, confirm the 80-pin footprint, and verify boot, debug, clock, USB, and peripheral functions before approving a substitution. For firmware-sensitive designs, retain the exact suffix in the tested BOM.
LPC1700-family devices can multiplex pins among USB, Ethernet, CAN, timers, and general-purpose I/O. Build the pin-assignment table early and avoid assigning a peripheral function until its alternate-function availability has been checked against the actual package. Leave required clock, reset, debug, and ground pins uncommitted, and ensure firmware, bootloader behavior, and peripheral clock configuration match the physical pin map.
اطلاعات انطباق
The NXP product page identifies the device as active. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the current manufacturer product-change and environmental documents.