LTC2144IUP-12 - 12-Bit 105Msps Dual ADC | Analog Devices
MPN: LTC2144IUP-12 ✓ فعالLTC2144IUP-12 نمای کلی
An ADC (Analog-to-Digital Converter) is a mixed-signal integrated circuit that converts continuous-time analog voltages into discrete digital codes. Pipelined ADCs use a multi-stage architecture to achieve high sample rates (tens to hundreds of Msps) while keeping per-stage hardware compact; dual simultaneous-sampling ADCs capture two channels at exactly the same instant, eliminating channel-to-channel skew in I/Q or diversity receivers. Within the power management and data-converter taxonomy, the LTC2144IUP-12 belongs to high-speed pipelined ADCs -> data converters -> mixed-signal ICs -> integrated circuits.
Key features of this part include 105 Msps per channel sample rate, 12-bit resolution, 70.6 dB SNR, 89 dB SFDR, 0.08 ps RMS aperture jitter, and a parallel CMOS/LVDS output interface selectable per channel. The 64-QFN (UP) exposed-pad package provides low thermal resistance (~28 C/W theta_JC via the pad), enabling operation across the industrial -40C to +85C temperature range.
The pipelined architecture uses 12 internal stages with per-stage flash sub-ADC and MDAC residue amplification; sample-and-hold is on-chip and front-end differential, supporting 1 Vp-p to 2 Vp-p full-scale inputs. A separate output supply (OVDD) lets the digital outputs drive 1.8V to 3.3V logic while the analog core runs from 1.8V.
Typical applications include communications receivers, cellular base-station digitizers, radar/sonar signal chains, medical imaging front-ends, and portable test instrumentation. Designers commonly pair it with the AD8138 differential driver at the input and an FPGA for the parallel data capture.
Design trade-off: at 105 Msps with 1.8V analog supply, expect roughly 100 mW per channel dissipation. Use the exposed pad with a continuous ground plane and bypass AVDD with 10 uF + 0.1 uF ceramic as close as possible to each pin pair.
This page synthesizes distributor pricing, drop-in same-package alternatives, and application-specific design notes not found in the manufacturer datasheet alone.
جایگزین‌های drop-in برای LTC2144IUP-12 — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای LTC2144IUP-12 (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, Resolution, RoHS Status, SFDR, SNR.
LTC2145IUP-12#PBF
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
LTC2143IUP-12#PBF
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
LTC2144CUP-12#PBF
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
LTC2144IUP-14#PBF
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
LTC2142IUP-14
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LTC2144IUP-12 حداکثر مقادیر مجاز و مشخصات الکتریکی
| رزولوشن | 12 bits |
| Sample Rate per Channel | 105 Msps |
| Number of Channels | 2 (simultaneous sampling) |
| Architecture | Pipelined |
| Input Type | Differential, 1 Vp-p to 2 Vp-p full-scale |
| SNR | 70.6 dB |
| SFDR | 89 dB |
| Aperture Jitter | 0.08 ps RMS |
| Output Interface | Parallel CMOS or LVDS (selectable per channel) |
| Analog Supply Voltage (AVDD) | 1.8 V |
| Output Supply Voltage (OVDD) | 1.8 V to 3.3 V |
| محدوده دمای کاری | -40C to +85C (industrial, 'I' grade) |
| بسته‌بندی | 64-pin QFN (UP) 9x9 mm with exposed pad |
| نوع نصب | Surface Mount |
| وضعیت RoHS | Compliant (#PBF suffix) |
پیکربندی پین LTC2144IUP-12
| پین 1 | GND — Ground |
| پین 2 | AIN1+ — Channel 1 differential input positive |
| پین 3 | AIN1- — Channel 1 differential input negative |
| پین 4 | GND — Ground |
| پین 5 | VCM1 — Channel 1 common-mode voltage |
| پین 6 | GND — Ground |
| پین 7 | AIN2+ — Channel 2 differential input positive |
| پین 8 | AIN2- — Channel 2 differential input negative |
| پین 9 | GND — Ground |
| پین 10 | VCM2 — Channel 2 common-mode voltage |
| پین 11 | GND — Ground |
| پین 12 | AVDD — 1.8V analog supply |
| پین 13 | AVDD — 1.8V analog supply |
| پین 14 | GND — Ground |
| پین 15 | AVDD — 1.8V analog supply |
| پین 16 | GND — Ground |
| پین 17 | SENSE — Internal reference mode select |
| پین 18 | GND — Ground |
| پین 19 | REFTOP — Reference top decoupling |
| پین 20 | REFBOT — Reference bottom decoupling |
| پین 21 | GND — Ground |
| پین 22 | REFH — High reference decoupling |
| پین 23 | REFL — Low reference decoupling |
| پین 24 | PAR/SER — Parallel/serial configuration select |
| پین 25 | GAIN — Gain select pin |
| پین 26 | OVDD — Output driver supply |
| پین 27 | OVDD — Output driver supply |
| پین 28 | GND — Ground |
| پین 29 | CLK+ — Differential clock input positive |
| پین 30 | CLK- — Differential clock input negative |
| پین 31 | GND — Ground |
| پین 32 | ENC+ — Encode input positive |
| پین 33 | ENC- — Encode input negative |
| پین 34 | GND — Ground |
| پین 35 | DA0 — LVDS data output 0 (channel 1) |
| پین 36 | DA1 — LVDS data output 1 (channel 1) |
| پین 37 | DA2 — LVDS data output 2 (channel 1) |
| پین 38 | DA3 — LVDS data output 3 (channel 1) |
| پین 39 | DA4 — LVDS data output 4 (channel 1) |
| پین 40 | DA5 — LVDS data output 5 (channel 1) |
| پین 41 | DA6 — LVDS data output 6 (channel 1) |
| پین 42 | DB0 — LVDS data output 0 (channel 2) |
| پین 43 | DB1 — LVDS data output 1 (channel 2) |
| پین 44 | DB2 — LVDS data output 2 (channel 2) |
| پین 45 | DB3 — LVDS data output 3 (channel 2) |
| پین 46 | DB4 — LVDS data output 4 (channel 2) |
| پین 47 | DB5 — LVDS data output 5 (channel 2) |
| پین 48 | DB6 — LVDS data output 6 (channel 2) |
| پین 49 | OVDD — Output driver supply |
| پین 50 | OVDD — Output driver supply |
| پین 51 | GND — Ground |
| پین 52 | FR — Frame output |
| پین 53 | CLKOUT — Clock output |
| پین 54 | DCO — Data clock output |
| پین 55 | OVDD — Output driver supply |
| پین 56 | GND — Ground |
| پین 57 | CS — SPI chip select |
| پین 58 | SCK — SPI serial clock |
| پین 59 | SDI — SPI serial data in |
| پین 60 | SDO — SPI serial data out |
| پین 61 | RESET — Power-on reset |
| پین 62 | SHDN — Shutdown control |
| پین 63 | NC — Not connected (per datasheet) |
| پین 64 | GND — Ground |
کاربردهای معمول
LTC2144IUP-12 مناسب است برای 6 کاربردs: Cellular Base-Station Receiver Digitizer, Radar and Sonar Signal Chain, Medical Imaging Front-End, Portable Test Instrumentation, Software-Defined Radio (SDR) Platform, Industrial Vibration and Acoustic Monitoring.
Cellular Base-Station Receiver Digitizer
The LTC2144IUP-12's 89 dB SFDR and 0.08 ps RMS aperture jitter let it undersample IF signals from WCDMA and LTE receivers while maintaining spurious-free performance above 80 dB. Its dual simultaneous channels digitize the main and diversity antenna paths from a single IC, eliminating channel-to-channel skew and reducing FPGA capture complexity. The 1.8V analog supply and ~100 mW per channel dissipation make thermal management straightforward in outdoor RRH units.
پیشنهادی
Radar and Sonar Signal Chain
Dual simultaneous-sampling 12-bit channels at 105 Msps let the LTC2144IUP-12 capture I/Q baseband from a radar IF stage with matched gain and phase. The 0.08 ps RMS jitter preserves the noise floor of weak returns, while the 64-QFN exposed pad keeps junction temperature under control during continuous duty cycle. Designers pair it with an FPGA that runs FFT-based Doppler processing on the parallel CMOS or LVDS output data.
پیشنهادی
Medical Imaging Front-End
Ultrasound and other medical imaging systems benefit from the LTC2144IUP-12's matched dual channels and 70.6 dB SNR to capture beamformed I/Q data with low quantization noise. The 64-QFN industrial-temperature grade supports portable cart-top equipment. The 1.8V analog supply plus 1.8-3.3V OVDD simplifies interface to modern low-power FPGAs, eliminating level shifters on the parallel data bus.
پیشنهادی
Portable Test Instrumentation
Handheld spectrum analyzers and oscilloscope front-ends use the LTC2144IUP-12 to digitize two channels of IF data at 105 Msps with low power. Its roughly 100 mW per channel dissipation is acceptable for battery-powered designs, and the dual simultaneous sampling enables phase-coherent multi-channel measurements. The exposed pad of the 64-QFN package provides adequate thermal headroom when stacked under a heat-spreading copper pour.
پیشنهادی
Software-Defined Radio (SDR) Platform
Wideband SDR platforms use the LTC2144IUP-12 to digitize I/Q pairs directly from a quadrature demodulator at sample rates up to 105 Msps. The 12-bit resolution and 70.6 dB SNR support a noise figure adequate for amateur, ISM-band, and light commercial reception. Its CMOS or LVDS parallel output interfaces directly to FPGA DSP fabric for real-time demodulation and decoding.
پیشنهادی
Industrial Vibration and Acoustic Monitoring
Two simultaneous 12-bit channels at 105 Msps allow the LTC2144IUP-12 to capture vibration and acoustic sensor data with exact phase alignment for FFT analysis. The industrial -40C to +85C temperature grade handles factory-floor environments, while the 64-QFN exposed pad simplifies thermal management in sealed enclosures. The on-chip sample-and-hold eliminates external track-and-hold circuits for two-axis accelerometer or microphone arrays.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای LTC2144IUP-12 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | LTC2145IUP-12#PBF | LTC2143IUP-12#PBF | LTC2144CUP-12#PBF | LTC2144IUP-14#PBF | LTC2142IUP-14 |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 64-QFN (UP) 9x9 | 64-QFN (UP) 9x9 - same | 64-QFN (UP) 9x9 - same | 64-QFN (UP) 9x9 - same | 64-QFN (UP) 9x9 - same | 64-QFN (UP) 9x9 - same |
| Resolution | 12 bits | 12 bits | 12 bits | 12 bits | 14 bits | 14 bits |
| Sample Rate per Channel | 105 Msps | 125 Msps (+19%) | 80 Msps (-24%) | 105 Msps | 105 Msps | 80 Msps (-24%) |
| Number of Channels | 2 simultaneous | 2 simultaneous | 2 simultaneous | 2 simultaneous | 2 simultaneous | 2 simultaneous |
| Operating Temperature Range | -40C to +85C (industrial) | -40C to +85C | -40C to +85C | 0C to +70C (commercial) | -40C to +85C | -40C to +85C |
| Analog Supply (AVDD) | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Output Interface | Parallel CMOS / LVDS | Parallel CMOS / LVDS | Parallel CMOS / LVDS | Parallel CMOS / LVDS | Parallel CMOS / LVDS | Parallel CMOS / LVDS |
تفاوت‌های کلیدی
- Dual simultaneous sampling eliminates channel skew (در مقابلLTC2144IUP-14#PBF)
- Higher speed grade available in same package (در مقابلLTC2143IUP-12#PBF)
- Industrial temperature range for harsh environments (در مقابلLTC2144CUP-12#PBF)
یادداشت‌های طراحی
Use a low-noise LDO such as the ADP7104 to generate the 1.8V AVDD rail from a 3.3V or 5V upstream supply. Place a 10 uF X7R ceramic plus a 0.1 uF NP0 ceramic within 2 mm of each AVDD pin; the same goes for the OVDD rail. Separate the analog and digital ground returns and join them only at the exposed pad of the 64-QFN, as recommended in the LTC2145-12/LTC2144-12/LTC2143-12 datasheet.
The 64-QFN (UP) package has an exposed thermal pad (pin 65) on the underside. Estimated: at 105 Msps with both channels active the part dissipates around 200 mW, giving a junction-to-ambient rise of roughly 20 C on a 4-layer board with a 25x25 mm ground pour. For sealed enclosures with limited airflow, expand the thermal copper pour to at least 30x30 mm or add a small heatsink.
Route the differential clock (CLK+/CLK-) and the encode input (ENC+/ENC-) as a 100 ohm differential pair with length matching to within 1 mm. Keep analog input traces (AIN1+/-, AIN2+/-) short and symmetric, and place the AD8138 or equivalent driver within 10 mm of the input pins to preserve the 89 dB SFDR. Avoid routing digital LVDS data outputs over the analog input region of the top layer.
Drive the clock input with a low-jitter source such as the AD9523-1 to take full advantage of the 0.08 ps RMS aperture jitter specification. A 5 ps RMS clock source will degrade SNR by approximately 3 dB at 105 Msps with a 70 MHz input. If the system requires a single-ended clock, AC-couple the unused CLK- input to ground with 0.1 uF.
Do not leave the SENSE pin floating - it selects internal or external voltage reference mode and defaults to internal reference if tied to AVDD. Always assert RESET after power-up and wait at least 1 ms before initiating the first SPI configuration. The exposed pad must be soldered to the ground plane for both electrical grounding and thermal dissipation; an unsoldered pad will trigger thermal shutdown at high ambient temperatures.
اطلاعات انطباق
RoHS compliance indicated by #PBF suffix per the DigiKey and Mouser listings. AEC-Q100 not applicable - this is a communications/instrumentation ADC rather than an automotive-qualified part. Halogen-free status not stated in the verified web data.
