MAX3232CDWRE4 - 250 kbit/s Dual RS-232 | Texas Instruments
MPN: MAX3232CDWRE4 ✓ فعالMAX3232CDWRE4 نمای کلی
An RS-232 transceiver is an interface IC that converts logic-level signals into voltage levels suitable for RS-232 links and then restores received RS-232 signals to logic levels. Within the interface hierarchy, the MAX3232CDWRE4 belongs to the RS-232 transceiver class of interface ICs, where it bridges a host UART or processor and an external data link. Its dual-channel architecture supports full-duplex point-to-point communication over two driver and two receiver channels.
Key features include operation from a 3 V to 5.5 V supply, support for 5 V logic, a data rate up to 250 kbit/s, and a typical supply current of 300 µA. The MAX3232 family meets or exceeds the requirements of TIA/EIA-232-F and ITU V.28. These characteristics make it suitable for industrial-control links, configuration ports, test equipment, and embedded systems that require a compact RS-232 interface without a separate charge-pump supply.
The device uses an internal charge-pump voltage converter with externally connected capacitors. These capacitors establish the positive and negative voltage rails required to drive RS-232 signals beyond ordinary 3.3 V or 5 V logic levels. The low supply current is particularly useful in systems where the serial interface remains enabled but carries infrequent traffic, because the transceiver can be placed in a power-saving state without removing the entire host from operation.
Typical applications include programmable instrument control, industrial equipment interfaces, point-of-sale terminals, service-console connections, and embedded debug or configuration ports. The dual receiver arrangement also permits a single transceiver to handle two independent incoming channels, while the dual driver arrangement supports two outgoing channels. System designers should still account for the slower and more noise-sensitive characteristics of RS-232 compared with differential interfaces such as RS-422 or RS-485.
For PCB implementation, place the charge-pump capacitors close to their designated pins and maintain the layout and grounding practices shown in the manufacturer datasheet. Keep the communication traces short where possible, provide a solid ground reference, and use suitable protection for externally accessible connectors. The main engineering trade-off is that the charge-pump design adds external capacitors and does not offer the noise immunity or multi-drop capability of a differential RS-485 interface.
This page organizes the principal electrical characteristics, package information, verified source links, drop-in alternatives, application guidance, and design considerations needed to evaluate the MAX3232CDWRE4 for a new RS-232 interface. It also highlights where temperature-grade, logic-interface, or channel-count differences can affect replacement decisions.
جایگزینهای drop-in برای MAX3232CDWRE4 — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای MAX3232CDWRE4 (همان فرمفاکتور و فوتپرینت) — متفاوت در Maximum Data Rate, Operating Temperature Range, Package, Product Type.
MAX3232EIDWR
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MAX3232CDE4
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MAX3232EIDW
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MAX3232CDWRE4 مشخصات
| Product Type | RS-232 line driver/receiver transceiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Transceiver Configuration | 2/2 full-duplex |
| Typical Supply Current | 300 µA |
| External Charge-Pump Capacitors | 0.1 µF each |
| Logic Compatibility | 5 V logic |
| RS-232 Compliance | Meets or exceeds TIA/EIA-232-F and ITU V.28 |
| محدوده دمای کاری | 0 °C to 70 °C |
| بستهبندی | 16-pin SOIC (DW) |
| Terminal Count | 16 |
| نوع نصب | Surface mount |
| Package Shape | Rectangular |
| Lead Form | Gull wing |
| وضعیت RoHS | Compliant |
راهنمای پیکربندی پین MAX3232CDWRE4 rectangular
پیکربندی پین برای MAX3232CDWRE4 (پکیج rectangular). شمارهگذاری پایهها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعملهای لحیمکاری به آن مراجعه کنید.
داده پینآوت تفصیلی موجود نیست برای MAX3232CDWRE4.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
MAX3232CDWRE4 مناسب است برای 6 کاربردs: Programmable Test Instrument Control, Industrial Controller Service Port, Point-of-Sale Terminal Interface, Embedded Configuration and Debug Port, Serial Console for Accessory Equipment, Legacy Data Acquisition Equipment.
Programmable Test Instrument Control
The MAX3232CDWRE4 fits host-to-instrument RS-232 control links because it combines two driver channels, two receiver channels, and operation up to 250 kbit/s from a 3 V to 5.5 V supply. It can connect a controller UART to legacy measurement equipment without adding a separate bipolar supply. The dual arrangement permits bidirectional traffic on two logical channels, while the low 300 µA typical supply current benefits portable or intermittently connected instruments. Confirm the instrument’s connector pinout, signal polarity, and cable length before enabling the interface.
پیشنهادی
Industrial Controller Service Port
The MAX3232CDWRE4 is appropriate for a service and configuration port on controllers operating within a 0 °C to 70 °C enclosure environment. Its 3 V to 5.5 V supply range allows use with 3.3 V or 5 V control hardware, and 250 kbit/s performance supports responsive configuration transfers and diagnostic traffic. Two transmitters and two receivers provide useful channel flexibility. For production equipment exposed to wider temperatures, select an explicitly industrial-temperature device instead of assuming the CD grade covers the installation environment.
پیشنهادی
Point-of-Sale Terminal Interface
The MAX3232CDWRE4 can support an RS-232 link between a point-of-sale terminal and a printer, scanner, or customer display through the appropriate legacy interface circuitry. Its dual driver and receiver configuration allows more than one point-to-point function when the attached devices use compatible signaling. Operation from 3 V to 5.5 V and acceptance of 5 V logic simplify integration with mixed-voltage terminal hardware. Keep charge-pump capacitors close to the IC and route the protected connector side away from sensitive logic to reduce noise coupling.
پیشنهادی
Embedded Configuration and Debug Port
The MAX3232CDWRE4 is useful for an embedded system’s configuration, firmware-recovery, or service-debug port when an RS-232 connector must remain available. The 250 kbit/s limit is ample for typical boot menus, parameter updates, and diagnostic logs, while 300 µA typical supply current helps when the port is monitored continuously. The interface should normally be enabled only when required to reduce both system power use and unintended activity on the bus. Add connector-level transient protection because the external cable is susceptible to ESD and surge events.
پیشنهادی
Serial Console for Accessory Equipment
The MAX3232CDWRE4 enables a compact RS-232 console between a main controller and an accessory such as a printer, modem, or legacy peripheral. Its 16-pin SOIC package supports dense PCB layouts, and its two transmit and two receive channels provide flexibility for multiple point-to-point links. The 3 V to 5.5 V supply operation permits use in both 3.3 V and 5 V embedded systems. Before connecting equipment, verify that the host uses the correct RS-232 signal levels rather than TTL UART levels, as the transceiver is not a direct TTL-to-serial replacement.
پیشنهادی
Legacy Data Acquisition Equipment
The MAX3232CDWRE4 can bridge a modern controller to data-acquisition equipment that retains an RS-232 command interface. The two receiver channels can accept status or measurement acknowledgments, while the driver channels support commands and requests when the connected equipment provides suitable isolated links. A 250 kbit/s rate accommodates moderate command traffic without requiring a modern differential-bus redesign. Because RS-232 is single-ended and susceptible to noise, use a short shielded cable, maintain a common ground reference, and avoid sharing unprotected connector wiring with high-current switching circuits.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای MAX3232CDWRE4 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | MAX3232EIDWR | MAX3232CDE4 | MAX3232EIDW |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-SOIC (DW) | 16-SOIC (DW) | 16-SOIC (DW) | 16-SOIC (DW) |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbit/s | 250 kbit/s | 250 kbit/s | 250 kbit/s |
| Driver and Receiver Count | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers | 2 drivers and 2 receivers |
| Temperature Grade | CD commercial grade, 0 °C to 70 °C | EID industrial grade | CD commercial grade | EID industrial grade |
| Typical Supply Current | 300 µA | 300 µA | 300 µA | 300 µA |
| External Charge-Pump Capacitors | 0.1 µF each | 0.1 µF each | 0.1 µF each | 0.1 µF each |
| RS-232 Standards | TIA/EIA-232-F and ITU V.28 | TIA/EIA-232-F and ITU V.28 | TIA/EIA-232-F and ITU V.28 | TIA/EIA-232-F and ITU V.28 |
تفاوتهای کلیدی
- Five-volt logic compatibility with a low 3 V minimum supply (در مقابلMAX3232EIDWR)
- Commercial temperature grade for controlled indoor environments (در مقابلMAX3232EIDWR)
- Two-channel RS-232 coverage in a 16-pin SOIC (در مقابلMAX3232CDE4)
یادداشتهای طراحی
Place the two 0.1 µF charge-pump capacitors close to the pins specified by the manufacturer datasheet and keep their return paths short. Follow the published component and trace arrangement rather than routing the capacitors according to generic high-frequency layout rules. This minimizes startup disturbance and charge-pump noise at the RS-232 drivers while retaining the 250 kbit/s signaling capability.
Separate the protected connector side of the interface from sensitive logic and clocks. RS-232 uses single-ended signals, so cable-borne noise and ground offsets can affect receiver performance even when the data rate is well below 250 kbit/s. Use a solid ground plane, minimize loop area around the interface, route connector and charge-pump currents separately, and follow the manufacturer datasheet layout to maintain usable signal integrity.
Do not connect RS-232 driver outputs directly to a TTL or CMOS UART without the MAX3232 interface stage, and do not interchange receiver inputs with driver outputs. Also verify that the CD commercial-grade part is acceptable for the enclosure temperature. MAX3232EIDWR may provide an industrial-temperature option in the same 16-SOIC family, but temperature grade, exact ordering code, and lead-frame details must be checked before substitution.
Add the input bypass and charge-pump capacitors recommended by the manufacturer, and test supply droop during RS-232 line activity. The 300 µA figure represents typical IC supply current rather than total system input current; capacitor charging, external loads, and interface state contribute additional demand. Confirm that the host supply remains stable during startup and repeated data transmission.
اطلاعات انطباق
RoHS compliance is identified for the target. The MAX3232 family is described as meeting or exceeding TIA/EIA-232-F and ITU V.28 requirements. No target-specific AEC-Q100 qualification is stated.