Texas Instruments

MAX3232CDWRE4 - 250 kbit/s Dual RS-232 | Texas Instruments

MPN: MAX3232CDWRE4 ✓ सक्रिय
3 V to 5.5 V Vdss 300 µA Id 16-pin SOIC (DW) Package
न्यूनतम ऑर्डर मात्रा: 1 |

MAX3232CDWRE4 अवलोकन

The Texas Instruments MAX3232CDWRE4 is a 3 V to 5.5 V dual RS-232 line driver and receiver supporting two transmit and two receive channels at speeds up to 250 kbit/s. The device is packaged in a 16-pin SOIC (DW) and uses external 0.1 µF charge-pump capacitors to generate the RS-232 bipolar voltage levels required for reliable serial communication.

An RS-232 transceiver is an interface IC that converts logic-level signals into voltage levels suitable for RS-232 links and then restores received RS-232 signals to logic levels. Within the interface hierarchy, the MAX3232CDWRE4 belongs to the RS-232 transceiver class of interface ICs, where it bridges a host UART or processor and an external data link. Its dual-channel architecture supports full-duplex point-to-point communication over two driver and two receiver channels.

Key features include operation from a 3 V to 5.5 V supply, support for 5 V logic, a data rate up to 250 kbit/s, and a typical supply current of 300 µA. The MAX3232 family meets or exceeds the requirements of TIA/EIA-232-F and ITU V.28. These characteristics make it suitable for industrial-control links, configuration ports, test equipment, and embedded systems that require a compact RS-232 interface without a separate charge-pump supply.

The device uses an internal charge-pump voltage converter with externally connected capacitors. These capacitors establish the positive and negative voltage rails required to drive RS-232 signals beyond ordinary 3.3 V or 5 V logic levels. The low supply current is particularly useful in systems where the serial interface remains enabled but carries infrequent traffic, because the transceiver can be placed in a power-saving state without removing the entire host from operation.

Typical applications include programmable instrument control, industrial equipment interfaces, point-of-sale terminals, service-console connections, and embedded debug or configuration ports. The dual receiver arrangement also permits a single transceiver to handle two independent incoming channels, while the dual driver arrangement supports two outgoing channels. System designers should still account for the slower and more noise-sensitive characteristics of RS-232 compared with differential interfaces such as RS-422 or RS-485.

For PCB implementation, place the charge-pump capacitors close to their designated pins and maintain the layout and grounding practices shown in the manufacturer datasheet. Keep the communication traces short where possible, provide a solid ground reference, and use suitable protection for externally accessible connectors. The main engineering trade-off is that the charge-pump design adds external capacitors and does not offer the noise immunity or multi-drop capability of a differential RS-485 interface.

This page organizes the principal electrical characteristics, package information, verified source links, drop-in alternatives, application guidance, and design considerations needed to evaluate the MAX3232CDWRE4 for a new RS-232 interface. It also highlights where temperature-grade, logic-interface, or channel-count differences can affect replacement decisions.

के लिए ड्रॉप-इन विकल्प MAX3232CDWRE4 — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं MAX3232CDWRE4 (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Maximum Data Rate, Operating Temperature Range, Package, Product Type.

Texas Instruments
Maximum Data Rate: 250 kbps
Operating Temperature Range: -40 °C to +85 °C
Package: 16-pin SOIC
इसके साथ तुलना करें MAX3232CDWRE4 →

MAX3232EIDWR

✅ ड्रॉप-इन
📦 16-SOIC (DW)
Uses the industrial EID temperature grade rather than the CD commercial grade; operating range differs by 15 °C at each temperature endpoint, while the 16-SOIC package and RS-232 function remain compatible.

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

MAX3232CDE4

✅ ड्रॉप-इन
Texas Instruments
📦 16-SOIC (DW)
RS-232 line driver/receiver transceiver · 2/2 · Full duplex · 3 V to 5.5 V · 250 kbps · ±15 kV HBM · 0 °C to 70 °C · 16-SOIC, 0.154 in (3.90 mm) width

कीमत के लिए संपर्क करें

डेटाशीट देखें →

MAX3232EIDW

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
Texas Instruments
📦 16-SOIC (DW)
Dual RS-232 line driver/receiver · 3 V to 5.5 V · 2 · 2 · 250 kbps · ±15 kV IEC · TIA/EIA-232-F · Single 3 V to 5.5 V supply

कीमत के लिए संपर्क करें

डेटाशीट देखें →

MAX3232CDWRE4 विशेषताएं

Product Type RS-232 line driver/receiver transceiver
Supply Voltage Range 3 V to 5.5 V
Maximum Data Rate 250 kbit/s
Number of Drivers 2
Number of Receivers 2
Transceiver Configuration 2/2 full-duplex
Typical Supply Current 300 µA
External Charge-Pump Capacitors 0.1 µF each
Logic Compatibility 5 V logic
RS-232 Compliance Meets or exceeds TIA/EIA-232-F and ITU V.28
ऑपरेटिंग तापमान रेंज 0 °C to 70 °C
पैकेज 16-pin SOIC (DW)
Terminal Count 16
माउंटिंग प्रकार Surface mount
Package Shape Rectangular
Lead Form Gull wing
RoHS स्थिति Compliant

MAX3232CDWRE4 rectangular पिन कॉन्फ़िगरेशन गाइड

MAX3232CDWRE4 (rectangular पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।

MAX3232CDWRE4 के लिए rectangular पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: MAX3232CDWRE4.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

MAX3232CDWRE4 के लिए उपयुक्त है 6 अनुप्रयोगs: Programmable Test Instrument Control, Industrial Controller Service Port, Point-of-Sale Terminal Interface, Embedded Configuration and Debug Port, Serial Console for Accessory Equipment, Legacy Data Acquisition Equipment.

🖥️

Programmable Test Instrument Control

The MAX3232CDWRE4 fits host-to-instrument RS-232 control links because it combines two driver channels, two receiver channels, and operation up to 250 kbit/s from a 3 V to 5.5 V supply. It can connect a controller UART to legacy measurement equipment without adding a separate bipolar supply. The dual arrangement permits bidirectional traffic on two logical channels, while the low 300 µA typical supply current benefits portable or intermittently connected instruments. Confirm the instrument’s connector pinout, signal polarity, and cable length before enabling the interface.

🏭

Industrial Controller Service Port

The MAX3232CDWRE4 is appropriate for a service and configuration port on controllers operating within a 0 °C to 70 °C enclosure environment. Its 3 V to 5.5 V supply range allows use with 3.3 V or 5 V control hardware, and 250 kbit/s performance supports responsive configuration transfers and diagnostic traffic. Two transmitters and two receivers provide useful channel flexibility. For production equipment exposed to wider temperatures, select an explicitly industrial-temperature device instead of assuming the CD grade covers the installation environment.

🖥️

Point-of-Sale Terminal Interface

The MAX3232CDWRE4 can support an RS-232 link between a point-of-sale terminal and a printer, scanner, or customer display through the appropriate legacy interface circuitry. Its dual driver and receiver configuration allows more than one point-to-point function when the attached devices use compatible signaling. Operation from 3 V to 5.5 V and acceptance of 5 V logic simplify integration with mixed-voltage terminal hardware. Keep charge-pump capacitors close to the IC and route the protected connector side away from sensitive logic to reduce noise coupling.

🔧

Embedded Configuration and Debug Port

The MAX3232CDWRE4 is useful for an embedded system’s configuration, firmware-recovery, or service-debug port when an RS-232 connector must remain available. The 250 kbit/s limit is ample for typical boot menus, parameter updates, and diagnostic logs, while 300 µA typical supply current helps when the port is monitored continuously. The interface should normally be enabled only when required to reduce both system power use and unintended activity on the bus. Add connector-level transient protection because the external cable is susceptible to ESD and surge events.

🔧

Serial Console for Accessory Equipment

The MAX3232CDWRE4 enables a compact RS-232 console between a main controller and an accessory such as a printer, modem, or legacy peripheral. Its 16-pin SOIC package supports dense PCB layouts, and its two transmit and two receive channels provide flexibility for multiple point-to-point links. The 3 V to 5.5 V supply operation permits use in both 3.3 V and 5 V embedded systems. Before connecting equipment, verify that the host uses the correct RS-232 signal levels rather than TTL UART levels, as the transceiver is not a direct TTL-to-serial replacement.

📡

Legacy Data Acquisition Equipment

The MAX3232CDWRE4 can bridge a modern controller to data-acquisition equipment that retains an RS-232 command interface. The two receiver channels can accept status or measurement acknowledgments, while the driver channels support commands and requests when the connected equipment provides suitable isolated links. A 250 kbit/s rate accommodates moderate command traffic without requiring a modern differential-bus redesign. Because RS-232 is single-ended and susceptible to noise, use a short shielded cable, maintain a common ground reference, and avoid sharing unprotected connector wiring with high-current switching circuits.

What is the operating voltage of MAX3232CDWRE4?
The MAX3232CDWRE4 operates from a 3 V to 5.5 V supply and accepts 5 V logic. According to the Texas Instruments MAX3232 datasheet, this range allows the same transceiver family to be used with 3.3 V and 5 V systems. The supply pins still require local high-frequency bypass capacitors, while the RS-232 line drivers generate their own bipolar levels through the charge-pump network.
What are the key specifications of MAX3232CDWRE4 that engineers should know?
The MAX3232CDWRE4 provides two RS-232 drivers, two receivers, and a maximum data rate of 250 kbit/s from a 3 V to 5.5 V supply. According to the Texas Instruments MAX3232 datasheet, its typical supply current is 300 µA, its charge-pump capacitors are 0.1 µF each, and it meets or exceeds TIA/EIA-232-F and ITU V.28 requirements. The device is supplied in a 16-pin SOIC package.
How fast is the MAX3232CDWRE4 RS-232 transceiver?
The MAX3232CDWRE4 operates up to 250 kbit/s, according to the Texas Instruments MAX3232 datasheet. This makes it appropriate for instrument control, configuration interfaces, and legacy equipment links that require more speed than a basic RS-232 port but do not justify changing to a differential bus. Cable length and signal integrity can reduce practical throughput, so the full system must still be characterized.
Where can I download the MAX3232CDWRE4 datasheet PDF?
The MAX3232CDWRE4 datasheet PDF can be opened through the datasheet link on this page or through the listed Texas Instruments document-access sources. The manufacturer datasheet is the controlling reference for pin assignments, charge-pump capacitor connections, typical characteristics, and recommended layout. Search specifically for MAX3232, because MAX3232CDWRE4 is an orderable package and temperature-grade suffix within the MAX3232 family.
Where can I find the MAX3232CDWRE4 pinout?
The MAX3232CDWRE4 pinout appears in the manufacturer datasheet under the pin-configuration and package-diagram sections. The part is a 16-pin SOIC, and its external 0.1 µF charge-pump capacitors connect to the pins identified by the datasheet. Use that table when assigning PCB nets and checking connector polarity, because the physical line-driver and receiver pins must not be interchanged.
What can replace the MAX3232CDWRE4?
The closest same-family drop-in choices identified for the MAX3232CDWRE4 are MAX3232EIDWR, MAX3232CDE4, and MAX3232EIDW, subject to package, temperature, and marking checks. The MAX3232EIDWR is the most direct candidate because the comparison source explicitly places it against the target and both use the 16-pin SOIC family. Verify the exact pinout and ordering suffix before committing a replacement to a PCB.
Is MAX3232EIDWR the same as MAX3232CDWRE4?
MAX3232EIDWR is closely related but is not an unconditional substitute for MAX3232CDWRE4. The dedicated comparison identifies the two parts for direct review and shows that package family, RoHS status, REACH status, series, and mounting style should be checked. The principal selection issue is the EID versus CD temperature-grade designation, which changes the environmental operating range and may not meet every commercial-only design requirement.
When should I choose MAX3232CDWRE4 over MAX3232EIDWR?
Choose MAX3232CDWRE4 when the product is intended for a commercial 0 °C to 70 °C operating environment and the MAX3232CDW ordering family is already controlled in the BOM. Choose MAX3232EIDWR when an industrial-temperature grade is required and its exact operating limits, package dimensions, and pin configuration have been verified. The interface functions are closely aligned, but temperature qualification and lifecycle planning can outweigh minor ordering differences.
Is MAX3232CDWRE4 suitable for an industrial-control RS-232 port?
MAX3232CDWRE4 is suitable for an RS-232 port in equipment whose environmental range remains within 0 °C to 70 °C. For unattended industrial equipment operating below 0 °C or above 70 °C, use a part explicitly qualified for the wider temperature range and verify its pinout. The 250 kbit/s capability, 3 V to 5.5 V supply, and dual-channel arrangement are otherwise well suited to controller-to-console links.
What is the best drop-in replacement for MAX3232CDWRE4?
MAX3232EIDWR is the best-supported drop-in candidate because a dedicated comparison directly identifies it against the target and describes both as 16-pin SOIC-family devices. It is not a universal answer: check operating temperature, electrical limits, pin names, package dimensions, and tape-and-reel orientation. MAX3232CDE4 and MAX3232EIDW are additional family candidates, but their exact ordering codes and production status require confirmation before substitution.
What is the best equivalent for MAX3232CDWRE4 from another manufacturer?
No cross-manufacturer drop-in equivalent is established by the cited cross-reference results for the MAX3232CDWRE4. The available results point to general component-matching tools and to same-family MAX3232 comparisons rather than a verified competitor with an identical 16-pin pinout. Selecting a different manufacturer would therefore require a separate pin-by-pin, capacitance, logic-level, data-rate, and lifecycle review rather than an assumption of interchangeability.
How much supply current does MAX3232CDWRE4 use?
The MAX3232CDWRE4 has a typical supply current of 300 µA, according to the Texas Instruments MAX3232 datasheet. This low operating current suits embedded and portable equipment in which an RS-232 interface remains connected during long idle periods. Final system consumption also depends on the selected charge-pump capacitors, external line-driver load, and how often the transceiver is enabled.
Why does MAX3232CDWRE4 need external capacitors?
The MAX3232CDWRE4 requires external 0.1 µF capacitors for its internal charge-pump and voltage-conversion functions. According to the Texas Instruments MAX3232 datasheet, these capacitors generate the bipolar voltage levels needed by RS-232 drivers from a single 3 V to 5.5 V supply. Their placement and connection should follow the manufacturer layout guidance to minimize noise, startup disturbance, and signal-integrity problems.
Where can I buy MAX3232CDWRE4 online?
Use the Request a Quote form on this page to request MAX3232CDWRE4 availability, current lead time, and order quantities. The structured price evidence does not contain a qualifying quantity-break table for this exact suffix, so this page does not publish a static unit-price schedule. The manufacturer part number, 16-pin SOIC package, and temperature grade should be included in the request to avoid an ambiguous MAX3232-family quotation.
What is the lead time and stock status for MAX3232CDWRE4?
Current stock and lead time for MAX3232CDWRE4 should be confirmed through the Request a Quote form on this page. No explicit quantity-break price table or dated stock quantity is established for the exact MPN, so static availability claims would be unreliable. When requesting a quotation, specify the desired quantity, reel format, target date, and whether substitutions are acceptable if the original manufacturer part is temporarily unavailable.
Does MAX3232CDWRE4 comply with RoHS and RS-232 standards?
The MAX3232CDWRE4 is identified as RoHS compliant, and the Texas Instruments MAX3232 datasheet states that the family meets or exceeds TIA/EIA-232-F and ITU V.28 requirements. According to the manufacturer documentation, the MAX3232EIDWR also meets RoHS and REACH requirements, while the target part's REACH status is not established here. Treat RoHS as a material declaration and RS-232 conformance as an electrical-interface requirement, not as interchangeable approvals.

के लिए इंजीनियरिंग संदर्भ डेटा MAX3232CDWRE4 — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose MAX3232CDWRE4 for a commercial-temperature RS-232 design that uses a 3.3 V or 5 V supply, requires two driver and two receiver channels, and needs data rates up to 250 kbit/s. Its 16-pin SOIC package, 0.1 µF charge-pump capacitors, and 300 µA typical supply current make it suitable for compact embedded, test, and service interfaces. Select MAX3232EIDWR when industrial-temperature qualification is more important than retaining the exact CD commercial-grade designation; the wider temperature range can prevent field failures outside 0 °C to 70 °C. MAX3232CDE4 is a same-family candidate when its commercial-grade characteristics and exact ordering code satisfy the production plan. MAX3232EIDW is useful when an industrial-grade, non-reel ordering option is confirmed. None of these choices should be treated as interchangeable without checking the exact pinout, package dimensions, temperature range, marking, and lifecycle status against the target design.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद MAX3232EIDWR MAX3232CDE4 MAX3232EIDW
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 16-SOIC (DW) 16-SOIC (DW) 16-SOIC (DW) 16-SOIC (DW)
Supply Voltage Range 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V
Maximum Data Rate 250 kbit/s 250 kbit/s 250 kbit/s 250 kbit/s
Driver and Receiver Count 2 drivers and 2 receivers 2 drivers and 2 receivers 2 drivers and 2 receivers 2 drivers and 2 receivers
Temperature Grade CD commercial grade, 0 °C to 70 °C EID industrial grade CD commercial grade EID industrial grade
Typical Supply Current 300 µA 300 µA 300 µA 300 µA
External Charge-Pump Capacitors 0.1 µF each 0.1 µF each 0.1 µF each 0.1 µF each
RS-232 Standards TIA/EIA-232-F and ITU V.28 TIA/EIA-232-F and ITU V.28 TIA/EIA-232-F and ITU V.28 TIA/EIA-232-F and ITU V.28

मुख्य विशेषताएँ

  • Five-volt logic compatibility with a low 3 V minimum supply (बनामMAX3232EIDWR)
  • Commercial temperature grade for controlled indoor environments (बनामMAX3232EIDWR)
  • Two-channel RS-232 coverage in a 16-pin SOIC (बनामMAX3232CDE4)

डिज़ाइन नोट्स

Place the two 0.1 µF charge-pump capacitors close to the pins specified by the manufacturer datasheet and keep their return paths short. Follow the published component and trace arrangement rather than routing the capacitors according to generic high-frequency layout rules. This minimizes startup disturbance and charge-pump noise at the RS-232 drivers while retaining the 250 kbit/s signaling capability.

Separate the protected connector side of the interface from sensitive logic and clocks. RS-232 uses single-ended signals, so cable-borne noise and ground offsets can affect receiver performance even when the data rate is well below 250 kbit/s. Use a solid ground plane, minimize loop area around the interface, route connector and charge-pump currents separately, and follow the manufacturer datasheet layout to maintain usable signal integrity.

Do not connect RS-232 driver outputs directly to a TTL or CMOS UART without the MAX3232 interface stage, and do not interchange receiver inputs with driver outputs. Also verify that the CD commercial-grade part is acceptable for the enclosure temperature. MAX3232EIDWR may provide an industrial-temperature option in the same 16-SOIC family, but temperature grade, exact ordering code, and lead-frame details must be checked before substitution.

Add the input bypass and charge-pump capacitors recommended by the manufacturer, and test supply droop during RS-232 line activity. The 300 µA figure represents typical IC supply current rather than total system input current; capacitor charging, external loads, and interface state contribute additional demand. Confirm that the host supply remains stable during startup and repeated data transmission.

अनुपालन जानकारी

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

RoHS compliance is identified for the target. The MAX3232 family is described as meeting or exceeding TIA/EIA-232-F and ITU V.28 requirements. No target-specific AEC-Q100 qualification is stated.

डेटा सत्यापन तिथि: 2026-11-09 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

MAX3232CDWRE4 datasheet MAX3232CDWRE4 pinout MAX3232CDWRE4 datasheet pdf Texas Instruments MAX3232CDWRE4 MAX3232CDWRE4 equivalent MAX3232CDWRE4 replacement MAX3232CDWRE4 cross reference MAX3232CDWRE4 vs MAX3232EIDWR MAX3232CDWRE4 16 SOIC pinout MAX3232CDWRE4 250 kbit/s RS-232 MAX3232CDWRE4 price MAX3232CDWRE4 stock MAX3232CDWRE4 application circuit MAX3232CDWRE4 schematic

संबंधित कंपोनेंट्स और शब्द

Texas Instruments MAX3232CDWRE4 MAX3232EIDWR MAX3232CDE4 MAX3232EIDW RS-232 transceiver RS-232 line driver RS-232 receiver interface IC semiconductor TIA/EIA-232-F ITU V.28 RoHS REACH 16-pin SOIC SOIC package family surface-mount package charge-pump capacitor 250 kbit/s data rate 300 µA supply current 3 V to 5.5 V supply industrial control test equipment embedded serial console point-to-point communication
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें