MAX3243EIPWRE4 - 500kbps RS-232 Transceiver | Texas Instruments
MPN: MAX3243EIPWRE4 ✓ فعالMAX3243EIPWRE4 نمای کلی
An RS-232 transceiver combines a line driver, which converts logic-level signals into RS-232 voltage levels, with a receiver, which converts incoming RS-232 signals back into logic-level voltages. The MAX3243EIPWRE4 provides three transmitters and five receivers, allowing five inbound channels and three outbound channels in one interface circuit. This integration reduces the number of separate interface ICs required in multi-channel equipment.
The MAX3243E family operates from a 3 V to 5.5 V supply, supporting both 3.3 V and 5 V system rails. Its maximum data rate is 500 kbps, making it appropriate for instrumentation, industrial control, data acquisition, point-of-sale equipment, and other serial interfaces operating well below that limit. The E designation corresponds to the enhanced ESD-protection version identified by the manufacturer.
The integrated protection is specified as plus-or-minus 15 kV IEC ESD protection. This feature is important when a board connects through an external connector or long cable because electrostatic discharge can otherwise damage the interface IC. Protection capability does not eliminate the need for sound board layout, controlled ground return paths, chassis grounding, and appropriate surge protection in severe environments.
The MAX3243EIPWRE4 is specified from minus 40 degrees Celsius to 85 degrees Celsius, covering industrial-temperature commercial equipment. Its 28-TSSOP package is suitable for compact, surface-mounted PCB layouts, but engineers should preserve adequate clearance around the package and route interface signals away from sensitive analog and clock paths.
When designing around this transceiver, verify that the host UART, cable connector, logic levels, and line termination match the intended RS-232 application. Software should also handle RS-232 control signals and the behavioral differences between DTE and DCE equipment. The manufacturer product page and datasheet are the authoritative references for electrical limits, pin assignments, truth tables, and recommended application circuits.
جایگزینهای drop-in برای MAX3243EIPWRE4 — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
MAX3243EIPWR
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MAX3243EIPWRE4 مشخصات
| Product Type | Multichannel RS-232 line driver/receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 500 kbps |
| Number of Transmitters | 3 |
| Number of Receivers | 5 |
| ESD Protection | +/-15 kV IEC ESD |
| محدوده دمای کاری | -40 C to +85 C |
| بستهبندی | 28-pin TSSOP |
| نوع نصب | Surface mount |
| Interface Standard | RS-232 |
| Logic Supply Voltage | 3 V to 5.5 V |
| Electrical Characteristics Document | 24 pages |
راهنمای پیکربندی پین MAX3243EIPWRE4 28-pin tssop
پیکربندی پین برای MAX3243EIPWRE4 (پکیج 28-pin tssop). شمارهگذاری پایهها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعملهای لحیمکاری به آن مراجعه کنید.
داده پینآوت تفصیلی موجود نیست برای MAX3243EIPWRE4.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
MAX3243EIPWRE4 مناسب است برای 6 کاربردs: Industrial Control Interfaces, Data Acquisition Systems, Point-of-Sale Equipment, Instrumentation and Test Systems, Network Equipment Management Ports, Embedded Serial Communication.
Industrial Control Interfaces
The MAX3243EIPWRE4 fits industrial controllers that exchange commands and status signals over RS-232. Its three transmitters support outbound control data, while five receivers can monitor acknowledgments, interlocks, alarms, and equipment status. The 3 V to 5.5 V supply range accommodates 3.3 V and 5 V logic systems, and the minus 40 C to 85 C operating range suits industrial-temperature equipment. Its plus-or-minus 15 kV IEC ESD protection adds robustness at external connectors, although proper grounding and system-level surge protection remain important.
پیشنهادی
Data Acquisition Systems
The MAX3243EIPWRE4 can serve as the host-side RS-232 interface in a data acquisition system. Five receiver channels allow multiple data-source enables, ready signals, synchronization inputs, or acknowledgments to be monitored, while three transmitter channels carry commands and collected data. Its 500 kbps maximum rate is suitable for many short-distance instrument links. Cable length, ground continuity, connector assignment, and the attached equipment's DTE or DCE role must be verified during system integration.
پیشنهادی
Point-of-Sale Equipment
Retail peripherals can use the MAX3243EIPWRE4 to consolidate several RS-232 links into one interface IC. A point-of-sale system may need to exchange commands with a printer, scanner, display, or customer interface while monitoring additional control lines. The device reduces package count by providing three transmitters and five receivers in one 28-pin TSSOP. Its 3 V to 5.5 V operation supports embedded systems using either common logic rail, while integrated IEC ESD protection improves robustness at accessible connector boundaries.
پیشنهادی
Instrumentation and Test Systems
The MAX3243EIPWRE4 is appropriate for laboratory and field instrumentation requiring several RS-232 control or status paths. The three driver channels can operate equipment or trigger measurement functions, and the five receiver channels can accept remote commands, interlock states, or completion signals. A 500 kbps interface rate supports instrument-control traffic while leaving margin below the device limit. Designers should use shielded cables, a common reference where appropriate, and clean grounding to minimize noise and ground-loop problems.
پیشنهادی
Network Equipment Management Ports
Network appliances can use the MAX3243EIPWRE4 for console, management, or service interfaces that require multiple RS-232 signals. Separate receiver channels can monitor power, fault, or enclosure-status lines, while the transmitters support console commands or service diagnostics. The 28-pin TSSOP package suits compact single-board designs, and the 3 V to 5.5 V supply range allows integration with modern 3.3 V control logic. For exposed chassis connections, maintain protective grounding and coordinate transient requirements with the enclosure design.
پیشنهادی
Embedded Serial Communication
The MAX3243EIPWRE4 fits embedded systems that retain legacy RS-232 for service, configuration, or peripheral communication. It can connect a host UART to several external devices without requiring one full transceiver per port. The 500 kbps capability covers numerous control protocols, and the five receiver inputs provide flexibility for handshake and status signaling. Firmware must configure unused lines deliberately, and hardware designers should check the exact connector pinout and signal direction for each attached DTE or DCE device.
پیشنهادی
دادههای مرجع مهندسی برای MAX3243EIPWRE4 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | MAX3243EIPWR |
|---|---|---|
| Package | 28-pin TSSOP | 28-pin TSSOP |
| Brand | Texas Instruments | Texas Instruments |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 500 kbps | 500 kbps |
| Number of Transmitters | 3 | 3 |
| Number of Receivers | 5 | 5 |
| ESD Protection | +/-15 kV IEC ESD | +/-15 kV IEC ESD |
| Operating Temperature Range | -40 C to +85 C | -40 C to +85 C |
| Interface Standard | RS-232 | RS-232 |
تفاوتهای کلیدی
- Combines five receivers and three transmitters in one package (در مقابلMAX3243EIPWR)
- Supports both common embedded logic rails (در مقابلMAX3243EIPWR)
- Combines 500 kbps operation with enhanced interface protection (در مقابلMAX3243EIPWR)
یادداشتهای طراحی
Route RS-232 driver outputs directly toward the connector and keep receiver inputs away from switching nodes and high-current traces. Maintain a continuous ground reference beneath or alongside the interface route, and avoid sharing narrow return paths with motors, relays, or switching regulators. Place optional external protection near the connector so surge current reaches the protection device before traveling through the PCB.
Decouple the MAX3243EIPWRE4 supply with local high-frequency and bulk capacitance close to the device. Keep the return path short and use a quiet ground reference for the interface IC. Because this is a 3 V to 5.5 V device, confirm that power-scaling behavior, startup behavior, and signal thresholds suit the host UART. Follow the manufacturer datasheet for exact capacitor values and test conditions.
Do not assume that every RS-232 connector uses the same signal names or directions as the transceiver pins. Verify DTE versus DCE assignments, unused receiver inputs, and handshake lines against both connected devices. Also avoid treating the specified plus-or-minus 15 kV IEC ESD rating as immunity to every surge or cable-length scenario; long cables may require additional system-level protection.
Confirm the ordering suffix before placing a replacement. The MAX3243EIPWR ordering designation is closely related to MAX3243EIPWRE4 and appears in the verified product records, but procurement and engineering teams should check the manufacturer ordering table for packing, temperature grade, and delivery-code differences. Pin compatibility alone does not resolve commercial or qualification differences.
اطلاعات انطباق
The verified manufacturer and distributor records identify the MAX3243EIPWRE4 as a 3 V to 5.5 V, 500 kbps RS-232 interface with plus-or-minus 15 kV IEC ESD protection. Specific RoHS, REACH, automotive, lead-free, halogen-free, and conflict-minerals declarations were not available.