MCF51JE256CLK - ColdFire V1 32-bit MCU, 256KB Flash | NXP
MPN: MCF51JE256CLK ⚠ آخرین فرصت خریدMCF51JE256CLK نمای کلی
What is a ColdFire V1 microcontroller? ColdFire V1 is a 32-bit RISC processor architecture derived from the original Motorola 68000 family, optimized for embedded applications that need higher performance than 8/16-bit MCUs but with the deterministic interrupt response and low power consumption required by industrial and consumer systems. The ColdFire V1 core sits within the broader hierarchy of 32-bit microcontroller cores -> microcontroller -> embedded processor -> semiconductor, and competes architecturally with ARM Cortex-M0/M0+ devices while preserving ColdFire instruction-set compatibility for legacy code bases.
The MCF51JE256CLK integrates a 12-bit SAR ADC with up to 20 channels, a 12-bit DAC, multiple timers (FTM, PWT, RTC), an I2C bus, two SCI/UART modules, and an SPI peripheral set. Its high-resolution analog front-end supports precision sensor conditioning in industrial metering and medical instrumentation. The integrated USB 2.0 Full-Speed On-The-Go (OTG) controller with dedicated PHY enables direct device/host/OTG roles without external transceivers.
Typical applications include industrial metering and data loggers, USB HID peripherals, smart sensors, medical monitoring devices, and low-power portable instrumentation. The wide operating voltage range of 2.7V to 5.5V makes it compatible with both 3.3V and 5V system rails. Multiple low-power modes (Wait, Stop, Standby) allow deep power optimization for battery-powered designs.
When designing with this MCU, allocate PCB area for a decoupling cap cluster near each power pin and ensure the USB D+/D- traces are 90-ohm differential-matched and as short as possible. For new designs, verify NXP's PCN notice for the MCF51JE family before committing, as several variants have entered End-of-Life status. The standard 80-LQFP footprint and JTAG/SWD debug path ease migration to alternate members of the JE family.
جایگزین‌های drop-in برای MCF51JE256CLK — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای MCF51JE256CLK (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, ADC, DAC, Number of I/O, Connectivity.
MCF51JE128VLK
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCF51JE256CMB
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCF51JE256VML
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCF51JE256CLH
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MCF51AG96CLK
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCF51MM128VLK
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCF51JE256CLK حداکثر مقادیر مجاز و مشخصات الکتریکی
| Core | ColdFire V1 (32-bit RISC) |
| Core Frequency | 50 MHz (50.3 MHz max) |
| Program Memory (Flash) | 256 KB (256K x 8) |
| RAM | 32 KB (32K x 8) |
| ولتاژ تغذیه | 2.7 V to 5.5 V |
| دمای کاری | -40 C to +85 C |
| Number of I/O | 47 |
| بسته‌بندی | 80-LQFP (12x12 mm) |
| ADC | 12-bit SAR, up to 20 channels |
| DAC | 12-bit |
| USB | USB 2.0 Full-Speed OTG with on-chip PHY |
| Communication Interfaces | 1x I2C, 2x SCI/UART, 1x SPI |
| Timers | FlexTimer (FTM), PWT, RTC |
| نوع نصب | Surface Mount |
| وضعیت RoHS | Compliant |
پیکربندی پین MCF51JE256CLK
| پین 1 | PTE0/TXD1 — Port E bit 0 / SCI1 transmit |
| پین 2 | PTE1/RXD1 — Port E bit 1 / SCI1 receive |
| پین 3 | PTE2 — Port E bit 2 |
| پین 4 | PTE3 — Port E bit 3 |
| پین 5 | VDD — Supply voltage (3.3V typical) |
| پین 6 | VSS — Ground |
| پین 7 | PTE4 — Port E bit 4 |
| پین 8 | PTE5 — Port E bit 5 |
| پین 9 | PTE6 — Port E bit 6 |
| پین 10 | PTE7 — Port E bit 7 |
| پین 11 | PTF0 — Port F bit 0 |
| پین 12 | PTF1 — Port F bit 1 |
| پین 13 | PTF2 — Port F bit 2 |
| پین 14 | PTF3 — Port F bit 3 |
| پین 15 | PTF4 — Port F bit 4 |
| پین 16 | PTF5 — Port F bit 5 |
| پین 17 | PTF6 — Port F bit 6 |
| پین 18 | PTF7 — Port F bit 7 |
| پین 19 | PTG0 — Port G bit 0 |
| پین 20 | PTG1 — Port G bit 1 |
| پین 21 | PTG2 — Port G bit 2 |
| پین 22 | PTG3 — Port G bit 3 |
| پین 23 | PTH0 — Port H bit 0 |
| پین 24 | PTH1 — Port H bit 1 |
| پین 25 | PTH2 — Port H bit 2 |
| پین 26 | PTH3 — Port H bit 3 |
| پین 27 | PTH4 — Port H bit 4 |
| پین 28 | PTH5 — Port H bit 5 |
| پین 29 | PTH6 — Port H bit 6 |
| پین 30 | PTH7 — Port H bit 7 |
| پین 31 | PTI0 — Port I bit 0 |
| پین 32 | PTI1 — Port I bit 1 |
| پین 33 | PTI2 — Port I bit 2 |
| پین 34 | PTI3 — Port I bit 3 |
| پین 35 | PTI4 — Port I bit 4 |
| پین 36 | PTI5 — Port I bit 5 |
| پین 37 | PTI6 — Port I bit 6 |
| پین 38 | PTI7 — Port I bit 7 |
| پین 39 | USB_DP — USB D+ data line |
| پین 40 | USB_DM — USB D- data line |
| پین 41 | VDD_USB — USB transceiver supply (3.3V) |
| پین 42 | VSS_USB — USB transceiver ground |
| پین 43 | PTA0 — Port A bit 0 |
| پین 44 | PTA1 — Port A bit 1 |
| پین 45 | PTA2 — Port A bit 2 |
| پین 46 | PTA3 — Port A bit 3 |
| پین 47 | PTA4 — Port A bit 4 |
| پین 48 | PTA5 — Port A bit 5 |
| پین 49 | PTA6 — Port A bit 6 |
| پین 50 | PTA7 — Port A bit 7 |
| پین 51 | PTB0/AD0 — Port B bit 0 / ADC channel 0 |
| پین 52 | PTB1/AD1 — Port B bit 1 / ADC channel 1 |
| پین 53 | PTB2/AD2 — Port B bit 2 / ADC channel 2 |
| پین 54 | PTB3/AD3 — Port B bit 3 / ADC channel 3 |
| پین 55 | PTB4/AD4 — Port B bit 4 / ADC channel 4 |
| پین 56 | PTB5/AD5 — Port B bit 5 / ADC channel 5 |
| پین 57 | PTB6/AD6 — Port B bit 6 / ADC channel 6 |
| پین 58 | PTB7/AD7 — Port B bit 7 / ADC channel 7 |
| پین 59 | PTC0/AD8 — Port C bit 0 / ADC channel 8 |
| پین 60 | PTC1/AD9 — Port C bit 1 / ADC channel 9 |
| پین 61 | PTC2/AD10 — Port C bit 2 / ADC channel 10 |
| پین 62 | PTC3/AD11 — Port C bit 3 / ADC channel 11 |
| پین 63 | PTC4/AD12 — Port C bit 4 / ADC channel 12 |
| پین 64 | PTC5/AD13 — Port C bit 5 / ADC channel 13 |
| پین 65 | PTC6/AD14 — Port C bit 6 / ADC channel 14 |
| پین 66 | PTC7/AD15 — Port C bit 7 / ADC channel 15 |
| پین 67 | PTD0/AD16/DAC0 — Port D bit 0 / ADC channel 16 / DAC output |
| پین 68 | PTD1/AD17/DAC1 — Port D bit 1 / ADC channel 17 / DAC output |
| پین 69 | PTD2/AD18 — Port D bit 2 / ADC channel 18 |
| پین 70 | PTD3/AD19 — Port D bit 3 / ADC channel 19 |
| پین 71 | PTD4 — Port D bit 4 |
| پین 72 | PTD5 — Port D bit 5 |
| پین 73 | PTD6 — Port D bit 6 |
| پین 74 | PTD7 — Port D bit 7 |
| پین 75 | RESET — External reset input (active low) |
| پین 76 | TCLK/PTA7 — Debug clock / PTA7 alternate |
| پین 77 | TDI/PTA1 — JTAG TDI / PTA1 alternate |
| پین 78 | TDO/PTA2 — JTAG TDO / PTA2 alternate |
| پین 79 | TMS/PTA3 — JTAG TMS / PTA3 alternate |
| پین 80 | TRST/PTA4 — JTAG TRST / PTA4 alternate |
کاربردهای معمول
MCF51JE256CLK مناسب است برای 6 کاربردs: Industrial Metering and Data Loggers, USB HID Peripherals and Human Interface Devices, Smart Sensor Hubs and Sensor Aggregators, Medical Monitoring Point-of-Care Devices, Low-Power Portable Instrumentation, Building Automation and HVAC Controllers.
Industrial Metering and Data Loggers
The MCF51JE256CLK is well-suited for industrial metering and data-logger designs, where 256KB Flash supports complex tariff/calibration tables, and the 12-bit SAR ADC with up to 20 channels handles multi-phase voltage and current sensing directly. Its integrated USB 2.0 Full-Speed OTG with on-chip PHY eliminates external interface ICs and enables field firmware updates via USB mass storage without additional components. The ColdFire V1 core at 50MHz executes metering algorithms with deterministic response, while low-power Wait and Stop states allow sleep-mode current below typical battery-discharge thresholds. Across the 2.7V to 5.5V supply range, the MCU runs directly from 3.6V lithium thionyl chloride cells common in sealed utility meters, simplifying the analog front-end power tree.
پیشنهادی
USB HID Peripherals and Human Interface Devices
The integrated USB 2.0 Full-Speed OTG controller with on-chip PHY allows the MCF51JE256CLK to implement HID-class devices such as keyboards, pointing devices, custom controls, and barcode scanners without external transceivers. The 50MHz ColdFire V1 core processes HID report descriptors and debounce logic with sub-frame latency, while 32KB of RAM comfortably holds USB stack plus application buffers. 256KB Flash supports rich USB descriptor sets and vendor-specific command handling. Operating from 2.7V to 5.5V covers both bus-powered 5V USB rails and 3.3V regulated internal supplies, simplifying single-PCB HID designs.
پیشنهادی
Smart Sensor Hubs and Sensor Aggregators
The MCF51JE256CLK is well matched to multi-sensor aggregation nodes thanks to its 12-bit SAR ADC with up to 20 channels, 12-bit DAC for excitation signals, and multiple serial interfaces (I2C, SPI, dual UART) for connecting external digital sensors. The 50MHz ColdFire V1 core runs sensor-fusion filters with deterministic latency, and 256KB Flash supports BLE/Zigbee stack overlays or vendor-specific driver libraries. Wide 2.7V-5.5V supply operation enables direct connection to 3.6V lithium or 5V regulated rails in distributed sensor systems, while low-power modes extend battery life in wireless environmental nodes.
پیشنهادی
Medical Monitoring Point-of-Care Devices
The MCF51JE256CLK fits point-of-care medical monitoring instruments where high-resolution analog front-end and USB data transfer are both required in a single device. Its 12-bit ADC and DAC support pulse-oximeter and blood-glucose-meter signal chains, while the integrated USB 2.0 OTG enables direct connection to host software for result logging. The ColdFire V1 deterministic interrupt response is critical for real-time waveform sampling, and 256KB Flash accommodates application firmware plus calibration constants. Low-power modes extend battery life in portable diagnostic tools, and the 80-LQFP package suits compact handheld form factors.
پیشنهادی
Low-Power Portable Instrumentation
The MCF51JE256CLK suits battery-powered portable test and measurement instruments, where its integrated 12-bit ADC, USB for charging/data transfer, and ColdFire V1 deterministic core combine in a single chip. The 2.7V to 5.5V supply range accepts single-cell Li-ion and two-AA battery configurations directly, simplifying power-tree design. Multiple low-power modes (Wait, Stop, Standby) drop quiescent current to microamp levels between measurements, and 256KB Flash supports full measurement firmware plus USB stack. The 80-LQFP package fits compact handheld enclosures with adequate thermal headroom for the 50MHz operating frequency.
پیشنهادی
Building Automation and HVAC Controllers
The MCF51JE256CLK fits building automation controllers that require USB commissioning ports plus analog sensor inputs for temperature, humidity, and air-quality measurements. Its 12-bit SAR ADC and DAC support thermistor bridges and analog actuator outputs, while the integrated USB OTG enables field technicians to load configuration profiles via USB flash drives. ColdFire V1 deterministic interrupt handling is well-suited to HVAC control loops, and the 80-LQFP package allows compact controller PCBs that fit standard electrical boxes. Wide operating voltage from 2.7V to 5.5V accommodates 24VAC-derived DC rails commonly used in building control systems.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای MCF51JE256CLK — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | MCF51JE128VLK | MCF51JE256CMB | MCF51AG96CLK | MCF51MM128VLK |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 80-LQFP (12x12 mm) | 80-LQFP (12x12 mm) - same | 81-MAPBGA - different package | 80-LQFP (12x12 mm) - same | 80-LQFP (12x12 mm) - same |
| Core | ColdFire V1 32-bit | ColdFire V1 32-bit | ColdFire V1 32-bit | ColdFire V1 32-bit | ColdFire V1 32-bit |
| Core Frequency | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz |
| Flash | 256 KB | 128 KB (-50%) | 256 KB | 96 KB (-62%) | 128 KB (-50%) |
| RAM | 32 KB | 32 KB | 32 KB | 16 KB (-50%) | 16 KB (-50%) |
| USB | USB 2.0 Full-Speed OTG with PHY | USB 2.0 Full-Speed OTG with PHY | USB 2.0 Full-Speed OTG with PHY | No USB | No USB |
| ADC | 12-bit SAR, 20 ch | 12-bit SAR, 20 ch | 12-bit SAR, 20 ch | 12-bit SAR, fewer ch | 12-bit SAR, 16 ch |
تفاوت‌های کلیدی
- Integrated USB 2.0 Full-Speed OTG PHY (در مقابلMCF51MM128VLK)
- Largest Flash in the JE family at 256KB (در مقابلMCF51JE128VLK)
- Higher ADC channel count with integrated 12-bit DAC (در مقابلMCF51AG96CLK)
یادداشت‌های طراحی
Decouple each VDD/VSS pair with 100nF ceramic plus 4.7uF bulk close to the IC. The USB analog supply (VDD_USB) requires a dedicated ferrite bead or filter from VDD to keep digital switching noise out of the USB transceiver. Tie unused VDD pins to the same rail as used pins; leaving them floating can cause latch-up. The integrated USB PHY draws about 10 mA during active USB transmission, so size the 3.3V regulator for at least 50 mA total MCU load including USB.
Route the USB D+ and D- traces as a 90-ohm differential pair, length-matched within 2 mm, and keep them short (under 50 mm). Place the ESD protection array within 5 mm of the USB connector. Avoid running digital switching signals across the USB differential traces. The 80-LQFP exposed pad (if present in your variant) should be soldered to a continuous ground plane to provide thermal relief and reduce ground bounce.
Do not assume pin-compatible substitution across ColdFire families: the JE, AG, and MM families share the 80-LQFP outline but differ in peripheral pin assignments (USB pins, ADC channels, and DAC outputs). Verify the pin map against your schematic before swapping. Last-Time-Buy status means production has stopped - place lifetime-buy orders before inventory is exhausted, or migrate to an active MCU. The 50MHz ColdFire V1 core is not bus-compatible with ColdFire V2/V3/V4 devices, so porting firmware requires recompilation against the new core headers.
اطلاعات انطباق
RoHS and lead-free per NXP product page. Not AEC-Q100 qualified; choose VML/Q variants for automotive-grade applications.