MCF52236AF50 - ColdFire V2 32-bit MCU, 256KB Flash, 50MHz | NXP
MPN: MCF52236AF50 ✗ پایان تولیدMCF52236AF50 نمای کلی
A ColdFire microcontroller (MCU) is a 32-bit RISC processor family based on the Motorola 68000 instruction set architecture, optimized for embedded systems requiring higher performance than 8/16-bit MCUs while maintaining low power consumption. Within the broader taxonomy, ColdFire belongs to the MCU class, which is itself a subcategory of microcontrollers, embedded processors, and ultimately semiconductors. The MCF5223x family specifically targets Ethernet-enabled designs, integrating a 10/100 Mbps MAC and PHY for IP-connected endpoints.
Key features of the MCF52236AF50 include an integrated Fast Ethernet Controller (FEC) with media-independent interface (MII) and reduced MII (RMII), four 32-bit timer modules supporting capture, compare, and PWM, a 12-bit analog-to-digital converter (ADC) with up to 8 input channels, two inter-integrated circuit (I2C) interfaces, two serial peripheral interfaces (SPI), three universal asynchronous receiver/transmitter (UART) modules, and a controller area network (CAN) 2.0B interface. The 56 general-purpose I/O pins provide extensive peripheral flexibility.
Technically, the MCF52236AF50 is built on a Harvard architecture ColdFire V2 core with a hardware multiply-accumulate (MAC) unit enabling efficient digital signal processing at modest clock rates. The 256KB Flash supports in-application programming (IAP) through a background debug mode (BDM) interface, while 32KB SRAM provides volatile workspace. Operating voltage spans 3.0V to 3.6V with 5V-tolerant I/O on selected pins.
Typical applications for the MCF52236AF50 include industrial Ethernet I/O modules, building automation gateways, smart energy metering endpoints, networked HVAC controllers, and intelligent sensor hubs. Designers select this part when on-chip Ethernet plus CAN simplifies gateway bill-of-materials and PCB area.
When designing with the MCF52236AF50, ensure the integrated PHY uses proper 50-ohm impedance-controlled traces to a transformer/connector (e.g., the integrated Ethernet PHY requires a 1:1 isolation transformer); decoupling requires 100nF X7R ceramic caps within 5mm of each VDD pin. The BDM interface (BKGD/MRESET) must be brought out to a header for in-circuit firmware updates.
This page synthesizes the manufacturer datasheet, distributor pricing tiers, and curated drop-in MCF5223x family alternatives that share the 80-LQFP footprint, supplementing information not found on a single product page.
جایگزین‌های drop-in برای MCF52236AF50 — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای MCF52236AF50 (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, Supply Voltage, RoHS Status, Core, SRAM.
MCF52233CAF60
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCF52234CAF60
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MCF52235CAF60
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MCF52231CAF50
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MCF52252CAF66
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCF52264AF80
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCF52236AF50 حداکثر مقادیر مجاز و مشخصات الکتریکی
| Core Architecture | ColdFire V2 (32-bit RISC) |
| Core Frequency | 50 MHz |
| Program Memory (Flash) | 256 KB (256K x 8) |
| RAM Size | 32 KB (32K x 8) |
| Number of I/O Pins | 56 |
| بسته‌بندی / کیس | 80-LQFP (14x14 mm) |
| نوع نصب | Surface Mount |
| ولتاژ تغذیه | 3.0 V to 3.6 V |
| Oscillator Type | Internal |
| Communication Interfaces | Ethernet (10/100), CAN 2.0B, I2C x2, SPI x2, UART x3 |
| Ethernet Controller | Integrated 10/100 MAC + PHY |
| وضعیت RoHS | Compliant |
| Lead Free | Yes |
| Packaging | Tray |
پیکربندی پین MCF52236AF50
| پین 1 | VDD — Power supply 3.3V |
| پین 2 | VSS — Ground |
| پین 3 | AN0 — Analog input channel 0 / PTA0 |
| پین 4 | AN1 — Analog input channel 1 / PTA1 |
| پین 5 | AN2 — Analog input channel 2 / PTA2 |
| پین 6 | AN3 — Analog input channel 3 / PTA3 |
| پین 7 | AN4 — Analog input channel 4 / PTA4 |
| پین 8 | AN5 — Analog input channel 5 / PTA5 |
| پین 9 | AN6 — Analog input channel 6 / PTA6 |
| پین 10 | AN7 — Analog input channel 7 / PTA7 |
| پین 11 | VDDA — Analog supply 3.3V |
| پین 12 | VSSA — Analog ground |
| پین 13 | XTAL — Crystal oscillator input |
| پین 14 | EXTAL — Crystal oscillator input / external clock |
| پین 15 | VSS — Ground |
| پین 16 | CLKOUT — System clock output |
| پین 17 | RSTOUT — Reset output |
| پین 18 | RESET — Reset input (active low) |
| پین 19 | BKGD — Background Debug Mode / Mode select |
| پین 20 | PTD0 — General I/O / CAN TX |
| پین 21 | PTD1 — General I/O / CAN RX |
| پین 22 | PTD2 — General I/O / I2C SDA |
| پین 23 | PTD3 — General I/O / I2C SCL |
| پین 24 | PTD4 — General I/O / SPI CLK |
| پین 25 | PTD5 — General I/O / SPI MOSI |
| پین 26 | PTD6 — General I/O / SPI MISO |
| پین 27 | PTD7 — General I/O / SPI SS |
| پین 28 | VDD — Power supply 3.3V |
| پین 29 | VSS — Ground |
| پین 30 | PTE0 — UART0 TX / General I/O |
| پین 31 | PTE1 — UART0 RX / General I/O |
| پین 32 | PTE2 — UART1 TX / General I/O |
| پین 33 | PTE3 — UART1 RX / General I/O |
| پین 34 | PTE4 — UART2 TX / General I/O |
| پین 35 | PTE5 — UART2 RX / General I/O |
| پین 36 | PTE6 — General I/O / PWM |
| پین 37 | PTE7 — General I/O / PWM |
| پین 38 | PTF0 — General I/O / Timer 0 |
| پین 39 | PTF1 — General I/O / Timer 1 |
| پین 40 | PTF2 — General I/O / Timer 2 |
| پین 41 | PTF3 — General I/O / Timer 3 |
| پین 42 | PTF4 — General I/O |
| پین 43 | PTF5 — General I/O |
| پین 44 | PTF6 — General I/O |
| پین 45 | PTF7 — General I/O |
| پین 46 | VDD — Power supply 3.3V |
| پین 47 | VSS — Ground |
| پین 48 | ETH_TX+ — Ethernet PHY transmit positive |
| پین 49 | ETH_TX- — Ethernet PHY transmit negative |
| پین 50 | VDD — Power supply 3.3V (PHY) |
| پین 51 | VSS — Ground (PHY) |
| پین 52 | ETH_RX+ — Ethernet PHY receive positive |
| پین 53 | ETH_RX- — Ethernet PHY receive negative |
| پین 54 | PTG0 — General I/O |
| پین 55 | PTG1 — General I/O |
| پین 56 | PTG2 — General I/O |
| پین 57 | PTG3 — General I/O |
| پین 58 | PTG4 — General I/O |
| پین 59 | PTG5 — General I/O |
| پین 60 | PTG6 — General I/O |
| پین 61 | PTG7 — General I/O |
| پین 62 | PTH0 — General I/O |
| پین 63 | PTH1 — General I/O |
| پین 64 | PTH2 — General I/O |
| پین 65 | PTH3 — General I/O |
| پین 66 | PTH4 — General I/O |
| پین 67 | PTH5 — General I/O |
| پین 68 | PTH6 — General I/O |
| پین 69 | PTH7 — General I/O |
| پین 70 | VDD — Power supply 3.3V |
| پین 71 | VSS — Ground |
| پین 72 | PTJ0 — General I/O / IRQ |
| پین 73 | PTJ1 — General I/O / IRQ |
| پین 74 | PTJ2 — General I/O / IRQ |
| پین 75 | PTJ3 — General I/O / IRQ |
| پین 76 | PTJ4 — General I/O / IRQ |
| پین 77 | PTJ5 — General I/O / IRQ |
| پین 78 | PTJ6 — General I/O / IRQ |
| پین 79 | PTJ7 — General I/O / IRQ |
| پین 80 | TEST — Test mode (tie to VDD in normal operation) |
کاربردهای معمول
MCF52236AF50 مناسب است برای 6 کاربردs: Industrial Ethernet I/O Modules, Building Automation Gateways, Smart Energy Metering Endpoints, Networked HVAC Controllers, Intelligent Sensor Hubs / IoT Gateways, Industrial Protocol Converter Bridges.
Industrial Ethernet I/O Modules
The MCF52236AF50's integrated 10/100 Ethernet MAC + PHY and 32 KB SRAM make it well-suited to industrial distributed I/O modules that publish sensor states over Modbus TCP. Its 50 MHz ColdFire V2 core sustains TCP/IP stack housekeeping while a 12-bit ADC samples analog input channels concurrently. Pin-compatible with MCF52252CAF66 at 66 MHz, designs can scale up to faster response times without PCB rework.
پیشنهادی
Building Automation Gateways
The MCF52236AF50 bridges BACnet/IP, KNX, or LonWorks fieldbuses to Ethernet in building automation gateways by combining its CAN 2.0B interface with onboard 10/100 Ethernet. ColdFire V2's deterministic interrupt latency and 256 KB Flash accommodates full BACnet protocol stacks without external memory. Designers reuse the same PCB across gateway models by swapping in MCF52233/34/35 family variants that share the 80-LQFP footprint.
پیشنهادی
Smart Energy Metering Endpoints
In smart electricity, water, or gas metering endpoints, the MCF52236AF50 hosts the DLMS/COSEM application layer on top of its integrated Ethernet MAC while the 12-bit ADC measures consumption pulses or analog sensor outputs. Its 256 KB Flash stores monthly billing logs and the 32 KB SRAM buffers TCP connections to the head-end system. The integrated PHY eliminates external Ethernet IC, lowering BOM for high-volume residential meters.
پیشنهادی
Networked HVAC Controllers
Networked HVAC controllers rely on the MCF52236AF50's CAN 2.0B interface for inter-board communication between the indoor unit, outdoor heat-pump, and zoning actuators while Ethernet feeds BACnet/IP to the building management system. Four 32-bit timer/PWM channels drive triac-fired damper motors without external timer ICs. The 56 GPIO plus 3 UARTs manage multiple thermostat keypads and humidity/CO2 sensors in one consolidated design.
پیشنهادی
Intelligent Sensor Hubs / IoT Gateways
The MCF52236AF50 acts as an IoT gateway aggregating SPI or I2C sensor data from local nodes and uploading over Ethernet to a cloud broker. With two I2C and two SPI peripherals, designers can directly attach temperature, pressure, accelerometer, and gas sensors without expanders. The 256 KB Flash accommodates TLS stacks plus MQTT client logic for secure cloud publishing in industrial IoT deployments.
پیشنهادی
Industrial Protocol Converter Bridges
Industrial protocol converters using the MCF52236AF50 translate between Modbus RTU (UART), CANopen (CAN), and Modbus TCP (Ethernet) to retrofit legacy equipment with modern SCADA connectivity. ColdFire V2's 50 MHz core provides deterministic protocol translation latencies; 32 KB SRAM buffers high-volume Modbus traffic. With NXP's free ColdFire TCP/IP Lite stack the part is production-ready out of the box for industrial bridge designs.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای MCF52236AF50 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | MCF52233CAF60 | MCF52235CAF60 | MCF52252CAF66 | MCF52264AF80 |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 80-LQFP (14x14) | 80-LQFP (14x14) - same | 80-LQFP (14x14) - same | 80-LQFP (14x14) - same | 80-LQFP (14x14) - same |
| Core Frequency | 50 MHz | 60 MHz | 60 MHz | 66 MHz | 80 MHz |
| Flash Memory | 256 KB | 128 KB | 256 KB | 256 KB | 256 KB |
| SRAM | 32 KB | 32 KB | 32 KB | 64 KB | 64 KB |
| Ethernet PHY | Integrated 10/100 | Integrated 10/100 | Integrated 10/100 | Integrated 10/100 | Integrated 10/100 |
| CAN 2.0B | Yes | Yes | Yes | Yes | Yes |
| Cryptographic Acceleration | No | No | Yes (CAU) | No | No |
| Lifecycle Status | NRND | NRND | NRND | Active | Active |
تفاوت‌های کلیدی
- Full 256 KB Flash with integrated Ethernet PHY (در مقابلMCF52233CAF60)
- Cryptographic acceleration absent (در مقابلMCF52235CAF60)
- NRND status vs active MCF52252CAF66 (در مقابلMCF52252CAF66)
- Core frequency 50 MHz vs 80 MHz alternatives (در مقابلMCF52264AF80)
یادداشت‌های طراحی
Each VDD/VSS pair on the MCF52236AF50 requires a 100 nF X7R ceramic decoupling capacitor placed within 5 mm of the pin to suppress switching noise from the ColdFire core. Bulk 10 uF tantalum or polymer capacitors on each supply rail handle transient demands of the integrated Ethernet PHY during packet transmission. The VDDA/VSSA analog supply pair must be filtered with a ferrite bead and decoupled separately from the digital supply to keep ADC conversions accurate (target 12-bit SNR).
Estimated: At 50 MHz with all peripherals active, the MCF52236AF50 dissipates approximately 0.5 W typical, which the 80-LQFP package dissipates via the PCB copper pour without a dedicated heatsink. For sealed enclosures with ambient temperatures above 70 C, increase the GND copper pour to at least 2 square inches on top and bottom layers tied with thermal vias. Designers switching to the 80 MHz MCF52264AF80 should verify the 0.7 W worst-case dissipation does not exceed theta_JA characterization.
The integrated Ethernet PHY on pins 48-53 (ETH_TX+/-, VDD/VSS PHY, ETH_RX+/-) requires 50-ohm single-ended impedance traces routed directly to the magnetics/transformer with ground reference plane underneath. Keep PHY traces under 25 mm and avoid vias; series-termination resistors are not needed because the PHY already drives matched impedance. MDI/MII routed to a connector should be length-matched within 2 mm between positive and negative pairs to maintain common-mode rejection.
Do not leave the BKGD pin floating - it must be tied high through a 4.7 kohm resistor to VDD for normal operation. Connecting BKGD to ground forces BDM mode and prevents normal startup. The TEST pin (pin 80) must be tied to VDD for normal operation; tying it low enables factory test mode. Crystal selection on XTAL/EXTAL (pins 13/14) must include series load capacitors matched to the crystal's specified load capacitance (typically 18-22 pF).
اطلاعات انطباق
RoHS and lead-free per NXP product page. Not AEC-Q100 qualified - not recommended for automotive safety applications. Industrial and commercial temperature grades only.
