MCP3426A1-E/MS - 16-Bit Dual-Channel Delta-Sigma ADC | Microchip
MPN: MCP3426A1-E/MS ✓ فعالMCP3426A1-E/MS نمای کلی
A delta-sigma ADC is a sigma-delta analog-to-digital converter that uses oversampling and digital filtering to provide high resolution and excellent noise performance. The MCP3426A1 belongs to the broader ADC → data converter → analog signal-processing IC hierarchy and is designed for measurements where low noise, differential input handling, and relatively low conversion rates are more important than very high throughput.
Key features include 16-bit resolution, two differential input channels, single-supply operation from 2.7 V to 5.5 V, and conversion rates up to 15 SPS. The integrated 2.048 V reference supports a differential input range of ±2.048 V. The device is packaged in an 8-pin MSOP, and the automotive-grade ordering code identifies the temperature-grade and qualification option associated with the manufacturer’s device family.
The MCP3426 architecture converts analog differential voltages through a delta-sigma modulator followed by digital filtering. This filtering averages noise over the measurement bandwidth and rejects periodic interference more effectively than many successive-approximation converters. The trade-off is conversion latency and reduced throughput, which make the device most appropriate for temperature, pressure, strain-gauge, current, and slowly changing industrial signals rather than waveform or motion acquisition.
Typical applications include bridge-based pressure and load-cell measurements, low-voltage current sensing, thermocouple and RTD conditioning, battery monitoring, and industrial process-control inputs. In each case, the differential inputs help reject common-mode noise when the sensor is connected through wiring that may pick up unwanted voltage. The 16-bit resolution improves the representation of small sensor outputs without requiring a faster converter.
For PCB implementation, keep the analog input traces short and route them away from switching power nodes and digital control lines. Use a clean, low-noise reference and adequate decoupling close to the supply pins. Because differential-input signal integrity depends on matched routing and filtering, the input source impedance and the acquisition timing should be checked against the manufacturer’s guidance before choosing external input networks.
This page combines the MCP3426A1-E/MS specifications with practical ADC design guidance, application-oriented interpretation, and same-package upgrade options. It is intended to help engineers evaluate the converter’s resolution, bandwidth, reference, supply range, package, and migration options before releasing a design.
جایگزینهای drop-in برای MCP3426A1-E/MS — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای MCP3426A1-E/MS (همان فرمفاکتور و فوتپرینت) — متفاوت در Differential Input Range, Package, Input Channels, Maximum Conversion Rate, Input Configuration.
MCP3426A1T-E/MS
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MCP3426A2-E/MS
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCP3426A3-E/MS
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
MCP3426A4-E/MS
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCP3426A5-E/MS
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
MCP3426A1-E/MS حداکثر مقادیر مجاز و مشخصات الکتریکی
| رزولوشن | 16 bit |
| Input Channels | 2 differential inputs |
| Converter Type | Delta-sigma sigma-delta ADC |
| Maximum Conversion Rate | 15 SPS |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Internal Reference Voltage | 2.048 V |
| Differential Input Range | ±2.048 V differential |
| بستهبندی | 8-pin MSOP |
| Package Type | Gull-wing surface-mount MSOP |
| Number of Terminals | 8 |
| Automotive Temperature Grade | Automotive |
| ولتاژ تغذیه کاری | 2.7 V minimum to 5.5 V maximum |
| Input Configuration | Two differential analog input channels |
| Converter Resolution Class | 16-bit ADC |
پیکربندی پین MCP3426A1-E/MS
| پین 1 | V+ — Positive analog input or positive supply-related connection; use the manufacturer pin-description table for the exact MCP3426 configuration |
| پین 2 | V- — Negative analog input or negative supply-related connection; use the manufacturer pin-description table for the exact MCP3426 configuration |
| پین 3 | VSS — Analog ground reference |
| پین 4 | VOUT — Reference or regulated output; confirm the function in the manufacturer pin-description table |
| پین 5 | VREF — Reference input or reference configuration pin |
| پین 6 | AIN0+ — Positive input for analog channel 0 |
| پین 7 | AIN0- — Negative input for analog channel 0 |
| پین 8 | AIN1 — Second analog input; confirm differential configuration in the manufacturer datasheet |
کاربردهای معمول
MCP3426A1-E/MS مناسب است برای 6 کاربردs: Bridge Pressure Sensor Measurement, Load-Cell and Strain-Gauge Interface, Low-Current Power Monitoring, Industrial Temperature Sensing, Battery Cell Voltage Acquisition, Precision Process-Control Instrumentation.
Bridge Pressure Sensor Measurement
The MCP3426A1-E/MS suits low-level bridge outputs because it combines 16-bit resolution with two differential input channels and a ±2.048 V range when its 2.048 V reference is used. The bridge can be excited from the ADC supply or a dedicated low-noise source, with its differential output connected directly to the converter. At no more than 15 SPS, the device is appropriate for static or slowly changing pressure because digital filtering suppresses periodic interference and averages noise, but a faster ADC is preferable for pressure transients or dynamic waveform analysis. The input common-mode voltage, bridge excitation, and filtering must remain within the manufacturer’s electrical limits.
پیشنهادی
Load-Cell and Strain-Gauge Interface
The MCP3426A1-E/MS is a practical ADC for load cells and strain gauges whose millivolt-level differential signals require more resolution than an 8-bit or 12-bit converter. Its 16-bit delta-sigma architecture can resolve small changes around a mechanical zero, while the two differential channels support redundant sensing or the use of an offset channel. The 15 SPS rate is well matched to static weighing, force monitoring, and slow-load calibration, but it is not intended for impact or vibration waveforms. Keep the bridge and converter on a clean analog ground region, use symmetric input routing, and verify the transducer’s excitation settling time before initiating each conversion.
پیشنهادی
Low-Current Power Monitoring
The MCP3426A1-E/MS can measure the differential voltage produced across a shunt resistor in battery, charger, or power-supply monitoring systems. Its differential inputs reject common-mode supply changes, while 16-bit resolution improves visibility into small current variations. The 2.048 V internal reference establishes a fixed conversion scale, and the 2.7 V to 5.5 V operating range allows operation alongside common low-voltage digital systems. Because the maximum conversion rate is 15 SPS, the device is better for supervisory current measurements than for fast overcurrent detection. The shunt power dissipation and the ADC input common-mode range should be checked independently during design.
پیشنهادی
Industrial Temperature Sensing
The MCP3426A1-E/MS can digitize temperature sensor signals in industrial equipment when the required bandwidth is modest. The two differential inputs can monitor RTDs, thermistor networks, or paired temperature sensors where rejecting common-mode noise improves measurement stability. Its 16-bit resolution is useful for preserving fractional-degree or fine-resolution information, and the delta-sigma digital filter helps suppress mains-related interference when its averaging bandwidth covers the relevant noise. At up to 15 SPS, the converter supports process monitoring rather than rapid thermal-event capture. External linearization, cold-junction compensation where appropriate, and sensor excitation circuitry remain application-specific.
پیشنهادی
Battery Cell Voltage Acquisition
The MCP3426A1-E/MS can support multi-cell battery monitoring when two differential cell voltages must be acquired with a shared precision reference. Its 16-bit resolution improves the representation of small voltage changes, while the ±2.048 V differential range covers common single-cell measurements when the input network is designed appropriately. The delta-sigma conversion process and 15 SPS rate are suitable for periodic supervisory readings rather than continuous ripple waveform capture. Care is needed to keep battery potentials within the ADC input limits, account for reference accuracy, and prevent cell-to-cell ground differences from injecting errors into the measurement reference.
پیشنهادی
Precision Process-Control Instrumentation
The MCP3426A1-E/MS fits slow industrial process-control channels that require high resolution and differential input conditioning. Two channels can measure redundant or complementary sensor outputs, while the onboard 2.048 V reference provides a convenient conversion baseline. Its digital-filtering behavior is advantageous for signals containing periodic interference, provided the resulting digital filter bandwidth and latency meet the control-loop requirements. The 15 SPS maximum rate suits supervisory loops and slow feedback updates, not high-bandwidth process dynamics. Designers should isolate analog routing from switching nodes, use low-noise supply arrangements, and calculate external filter settling for the source impedance before sampling.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای MCP3426A1-E/MS — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | MCP3426A1T-E/MS | MCP3426A2-E/MS | MCP3426A3-E/MS | MCP3426A4-E/MS | MCP3426A5-E/MS |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | MSOP-8 | MSOP-8 - same | MSOP-8 - same | MSOP-8 - same | MSOP-8 - same | MSOP-8 - same |
| Resolution | 16 bit | 16 bit | 16 bit | 16 bit | 16 bit | 16 bit |
| Converter Architecture | Delta-sigma sigma-delta ADC | Delta-sigma sigma-delta ADC | Delta-sigma sigma-delta ADC | Delta-sigma sigma-delta ADC | Delta-sigma sigma-delta ADC | Delta-sigma sigma-delta ADC |
تفاوتهای کلیدی
- Direct 16-bit differential measurement in a compact package (در مقابلMCP3426A1T-E/MS)
- Two differential channels support redundant sensing (در مقابلMCP3426A2-E/MS)
- Integrated precision reference simplifies the measurement chain (در مقابلMCP3426A3-E/MS)
یادداشتهای طراحی
Route the two differential inputs as a compact, symmetric pair away from switching regulators, relay contacts, and high-current return paths. Place input filtering components close to the ADC pins and terminate unused inputs according to the manufacturer guidance. Differential benefit depends on the sensor and reference sharing the same operating environment; poor grounding or asymmetric input impedances can reduce the common-mode rejection expected from a differential ADC.
Account for the source impedance and the delta-sigma input-filter settling time before initiating a conversion. A high-impedance sensor or long analog trace may not settle completely at the selected conversion rate. Use a low-value, low-noise input network that preserves the required measurement bandwidth, and evaluate the filter’s effect on sensor excitation and output loading. The 15 SPS maximum rate should not be mistaken for permission to increase source impedance without recalculation.
Use a clean supply for the ADC and place its decoupling capacitor close to the supply pins. If an external reference is selected, follow the manufacturer’s reference-bypass requirements and account for reference noise in the overall measurement uncertainty. The onboard 2.048 V reference simplifies the analog chain, but its accuracy and thermal behavior still contribute to conversion error and should be included in the system error budget.
Do not substitute an SOIC ordering code for the MSOP device without verifying the footprint; MCP3426A1-E/SN uses an 8-pin SOIC and is not package-match compatible with MCP3426A1-E/MS. Likewise, do not assume every MCP3426 gain-code variant has identical conversion timing. Confirm the complete ordering code, package drawing, pin assignments, qualification, and electrical limits in the manufacturer documentation before releasing a PCB or production BOM.
اطلاعات انطباق
The verified listing identifies an automotive temperature-grade ordering option, but it does not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals compliance.