MCP3426A6-E/MC - 16-Bit Dual-Channel ADC | Microchip
MPN: MCP3426A6-E/MC ✓ فعالMCP3426A6-E/MC نمای کلی
A delta-sigma ADC is an analog-to-digital converter that uses oversampling and digital filtering to provide high resolution and noise performance from low-frequency sensor signals. In the broader device hierarchy, it belongs to the ADC and DAC class, sits below data converters, and operates as a mixed-signal interface IC. Differential inputs allow the converter to reject common-mode noise when a sensor is measured across two input lines.
Key features include up to 16-bit conversion resolution, two independent analog input channels, differential operation, an internal 2.048 V reference, and a two-wire I2C digital interface. The 2.048 V reference establishes a differential input range of ±2.048 V according to the Microchip product page. This combination suits sensors whose output is centered around zero and whose signal amplitude fits the converter’s differential range.
The MCP3426 family combines continuous conversion operation with low-noise delta-sigma conversion. Its two-wire interface reduces the number of signal connections required when the converter shares a bus with other sensors or a microcontroller. The A6 ordering option is identified in distributor records as a 15 SPS configuration, making it appropriate for slow-changing measurements where moderate throughput is more important than maximum sampling speed.
Typical uses include pressure, temperature, strain, and low-level analog sensor instrumentation, as well as industrial monitoring systems and battery-powered measurement nodes. Differential sensor connections are particularly useful when sensor wiring is long or when the measured signal is small relative to environmental electrical noise.
PCB design should preserve a quiet analog signal path, provide effective decoupling at VDD and VREF, and route the differential inputs away from switching nodes and high-current traces. Differential input filtering, grounding, and connector placement can materially affect the noise performance observed in the final conversion result.
This product page combines the manufacturer specifications with practical guidance for PCB implementation, application selection, pin assignment, and drop-in replacement assessment. It also identifies where speed, resolution, package, addressing, or interface differences must be checked before treating another MCP3426 ordering code as a replacement.
جایگزینهای drop-in برای MCP3426A6-E/MC — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای MCP3426A6-E/MC (همان فرمفاکتور و فوتپرینت) — متفاوت در Digital Interface, Number of Input Channels, Package, Conversion Rate.
MCP3426A0-E/MC
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCP3426A1-E/MC
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCP3426A4-E/MC
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCP3426A6-E/MC حداکثر مقادیر مجاز و مشخصات الکتریکی
| Converter Type | 16-bit delta-sigma ADC |
| Number of Input Channels | 2 channels |
| Conversion Rate | 15 SPS |
| رزولوشن | Up to 16 bits |
| Input Architecture | Differential inputs |
| Internal Reference Voltage | 2.048 V |
| Differential Input Range | ±2.048 V |
| Digital Interface | Two-wire I2C |
| بستهبندی | 8-DFN, 2 x 3 mm |
| نوع نصب | Surface mount |
| Exposed Pad | Present |
پیکربندی پین MCP3426A6-E/MC
| پین 1 | VDD — Positive analog supply input |
| پین 2 | VREF — Reference voltage input and internal reference bypass connection |
| پین 3 | AIN0- — Negative input for analog channel 0 |
| پین 4 | AIN0+ — Positive input for analog channel 0 |
| پین 5 | AIN1- — Negative input for analog channel 1 |
| پین 6 | AIN1+ — Positive input for analog channel 1 |
| پین 7 | SCL — I2C clock input |
| پین 8 | SDA — I2C data input and output |
کاربردهای معمول
MCP3426A6-E/MC مناسب است برای 6 کاربردs: Industrial Pressure Sensing, Precision Temperature Acquisition, Battery-Powered Sensor Nodes, Strain and Load Cell Instrumentation, Environmental Monitoring Equipment, Battery Chemistry Measurement.
Industrial Pressure Sensing
The MCP3426A6-E/MC suits bridge or ratiometric pressure sensors whose output is small, differential, and changes relatively slowly. Its two differential input channels can monitor two sensing elements, while the 2.048 V internal reference supports measurements within a ±2.048 V differential range. At 15 SPS, the converter is suited to static or slowly varying process variables rather than transient waveform capture. Differential routing helps reduce common-mode pickup from factory wiring and surrounding switching equipment. Engineers should verify the sensor output range, input common-mode limits, and excitation scheme before finalizing the analog front end.
پیشنهادی
Precision Temperature Acquisition
The MCP3426A6-E/MC can digitize low-level outputs from resistive temperature sensors, RTD conditioning networks, or temperature sensors with a differential output. A 15 SPS conversion rate is generally appropriate for thermal measurements that evolve over seconds rather than milliseconds, and the 16-bit conversion resolution preserves fine code-level detail. The ±2.048 V differential range can accommodate suitably conditioned bipolar signals without a separate external reference. The compact 8-DFN package also conserves board space in multi-channel monitoring equipment. Input filtering and thermal placement remain important because sensor noise and gradient can dominate the final measurement accuracy.
پیشنهادی
Battery-Powered Sensor Nodes
The MCP3426A6-E/MC is appropriate for compact, battery-operated sensor nodes that report slow-changing measurements over a two-wire serial bus. The 15 SPS rate limits conversion throughput to a level that many environmental, energy, and occupancy sensors do not need, helping align acquisition demand with low-power system behavior. Its dual-channel architecture can reduce the number of separate converter packages when two low-frequency analog quantities must be measured. The 8-DFN 2 x 3 mm footprint supports dense portable assemblies. Firmware must request the supported conversion rate, handle the programmed I2C address correctly, and use sleep or duty-cycle strategies between measurements.
پیشنهادی
Strain and Load Cell Instrumentation
The MCP3426A6-E/MC is well matched to differential strain-gauge and load-cell front ends, where the useful signal appears across two bridge nodes and common-mode voltage can be substantial. The converter evaluates the difference between the analog input pairs rather than measuring either node independently, which helps reject shared noise. Up to 16-bit resolution supports detailed signal representation, and the 2.048 V internal reference defines a differential measurement range of ±2.048 V. Mechanical excitation, settling time, bridge supply behavior, and cable interference must be considered. A stable excitation source and careful guard or return-path layout are often more important to final accuracy than converter resolution alone.
پیشنهادی
Environmental Monitoring Equipment
The MCP3426A6-E/MC can monitor environmental sensors that change over seconds or minutes, including gas, humidity, pH, and light sensors with conditioned analog outputs. Two differential channels allow one converter to service two sensing channels while retaining a compact 8-DFN footprint. The 15 SPS operation provides frequent updates without requiring a high-speed SAR ADC, and the internal 2.048 V reference simplifies analog-range planning. Because environmental sensors often have slow response times, input filters can suppress periodic interference without preventing useful updates. The I2C interface also supports compact embedded instrumentation with a microcontroller controlling conversion timing and data acquisition.
پیشنهادی
Battery Chemistry Measurement
The MCP3426A6-E/MC can acquire differential cell-voltage or balancing-system signals in laboratory battery monitoring equipment where accuracy is required at relatively low update rates. Its 16-bit resolution can represent small voltage changes, while the two input channels can monitor adjacent elements or two measurement points. The 15 SPS rate is suitable for battery aging and capacity tests in which voltage evolves gradually. The differential architecture helps reject common-mode variation if the measurement remains within the specified input and common-mode limits. Designers should compensate sensor and wiring errors in calibration, confirm whether the chosen ordering code’s configuration supports the intended I2C address, and provide stable reference and supply decoupling.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای MCP3426A6-E/MC — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | MCP3426A0-E/MC | MCP3426A1-E/MC | MCP3426A4-E/MC |
|---|---|---|---|---|
| Package | 8-DFN, 2 x 3 mm | 8-DFN, 2 x 3 mm | 8-DFN, 2 x 3 mm | 8-DFN, 2 x 3 mm |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Converter Type | 16-bit delta-sigma ADC | 16-bit delta-sigma ADC | 16-bit delta-sigma ADC | 16-bit delta-sigma ADC |
| Input Channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Input Architecture | Differential | Differential | Differential | Differential |
| Internal Reference | 2.048 V | 2.048 V | 2.048 V | 2.048 V |
| Differential Input Range | ±2.048 V | ±2.048 V | ±2.048 V | ±2.048 V |
| Digital Interface | Two-wire I2C | Two-wire I2C | Two-wire I2C | Two-wire I2C |
| Factory-Programmed Configuration | A6 ordering code | A0 ordering code | A1 ordering code | A4 ordering code |
تفاوتهای کلیدی
- Verified same-family substitute with matching physical architecture (در مقابلMCP3426A0-E/MC)
- Dual differential channels in a compact footprint (در مقابلMCP3426A1-E/MC)
- 15 SPS operating point for slow-changing measurements (در مقابلMCP3426A4-E/MC)
یادداشتهای طراحی
Place the VDD and VREF decoupling capacitors immediately beside their associated device pins, with the VREF connection routed away from analog input traces. The manufacturer application guidance emphasizes short, compact connections around the converter because long supply and reference paths can introduce impedance and coupling. Connect the exposed pad according to the data-sheet land pattern, and provide uninterrupted ground-plane area beneath the package.
Route AIN0+ and AIN0- as a closely coupled differential pair, and keep AIN1+ and AIN1- together on the opposite side of the device when practical. Avoid crossing sensitive input traces with digital clock lines, relay-control nets, DC-DC converter switches, and high-current return paths. Connectors and sensor returns can introduce common-mode and ground-potential errors, so input grounding should be evaluated as part of the complete measurement chain.
Apply differential filtering close to the analog pins when the sensor bandwidth permits it. Filter values should preserve the required response time at the 15 SPS conversion rate rather than unnecessarily suppressing useful signal changes. For slow sensors, additional digital averaging in firmware can improve repeatability, but it must not create an aliased result if the analog signal changes significantly between conversion commands.
Do not treat every MCP3426 ordering code as electrically interchangeable without checking the factory-programmed configuration and I2C address. The physical package can remain unchanged while bus addressing or conversion timing differs. Also keep the differential input voltage and each input’s common-mode voltage within the manufacturer’s limits; the ±2.048 V differential range alone does not imply unrestricted input-node voltages.
اطلاعات انطباق
Compliance status for the exact MCP3426A6-E/MC ordering code was not stated in the available manufacturer or distributor information. Confirm RoHS, REACH, automotive qualification, lead-free, halogen-free, and conflict-minerals documentation with Microchip before releasing a regulated production design.