MCP601T-I/SN - 2.8MHz Low-Power Op Amp | Microchip
MPN: MCP601T-I/SN ✓ فعالMCP601T-I/SN نمای کلی
An operational amplifier is a voltage-feedback amplifier used to increase signal amplitude, buffer high-impedance sources, compare voltages, or drive external loads through feedback. The MCP601 belongs to the broader CMOS operational-amplifier hierarchy, combining low input bias current, moderate gain bandwidth, high open-loop gain, and rail-to-rail output capability in a low-power integrated circuit.
Its 2.8 MHz gain-bandwidth product supports general-purpose signal conditioning at moderate frequencies. The 230 uA typical operating current is useful for portable and low-power systems, while the less-than-2 mV typical input offset supports precision-oriented applications. Rail-to-rail output operation maximizes usable output swing from a 2.7 V to 5.5 V supply, and the common-mode input range below ground simplifies single-supply sensing near zero volts.
The advanced CMOS implementation provides low bias current, high-speed operation, and high open-loop gain. With unity-gain stability, the device can be configured as a non-inverting or inverting amplifier without an additional compensation network. Its low quiescent current makes it appropriate for continuously powered sensor circuits, where every microampere contributes to the overall system power budget.
Typical uses include current sensing, portable instrumentation, sensor signal conditioning, low-frequency active filters, audio input stages, and industrial control interfaces. The 8-pin SOIC format is suitable for conventional surface-mount assembly, while the operating range and low-power characteristics support designs operating from regulated 3.3 V or 5 V rails.
For stable operation, place input and feedback components close to the amplifier pins, avoid long high-impedance input traces, and provide adequate bypassing between VDD and VSS. Common-mode and output-headroom checks are essential when operating near the supply rails, particularly with 2.7 V systems.
This page combines manufacturer specifications, sourcing guidance, drop-in family alternatives, comparison data, and practical circuit-design notes. These resources help engineers evaluate the MCP601T-I/SN beyond basic catalog parameters and select it for low-power, rail-to-rail signal-processing applications.
جایگزینهای drop-in برای MCP601T-I/SN — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای MCP601T-I/SN (همان فرمفاکتور و فوتپرینت) — متفاوت در Package, Typical Offset Voltage.
MCP601T-E/SN
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCP601-I/SN
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCP601T-I/SN حداکثر مقادیر مجاز و مشخصات الکتریکی
| Product Type | Single operational amplifier |
| Channel Count | 1 circuit |
| Gain-Bandwidth Product | 2.8 MHz |
| Typical Operating Current | 230 uA |
| Typical Input Offset Voltage | <2 mV |
| Minimum Supply Voltage | 2.7 V |
| Maximum Supply Voltage | 5.5 V |
| Output Swing | Rail-to-rail |
| Common-Mode Input Swing | Below ground to upper rail |
| Unity-Gain Stability | 1 |
| Process Technology | Advanced CMOS |
| بستهبندی | 8-pin SOIC |
| نوع نصب | Surface mount |
پیکربندی پین MCP601T-I/SN
| پین 1 | OUT — Operational-amplifier output |
| پین 2 | VSS — Negative supply or ground connection |
| پین 3 | +IN — Non-inverting input |
| پین 4 | -IN — Inverting input |
| پین 5 | NC — Not connected |
| پین 6 | VDD — Positive supply connection |
| پین 7 | NC — Not connected |
| پین 8 | NC — Not connected |
کاربردهای معمول
MCP601T-I/SN مناسب است برای 6 کاربردs: Portable Sensor Signal Conditioning, Battery-Powered Measurement Circuit, Precision Current Sensing, Active Audio Input Stage, Industrial Threshold Detection, Low-Frequency Active Filter.
Portable Sensor Signal Conditioning
The MCP601T-I/SN fits low-power sensor interfaces because its 230 uA typical operating current and 2.7 V minimum supply voltage allow operation close to the lower limits of a regulated battery rail. Place the amplifier in a non-inverting configuration when the sensor output must be biased around mid-supply, or use an inverting configuration when summing and impedance conversion are required. The rail-to-rail output helps preserve signal amplitude, while the input range extending below ground supports sensors whose output approaches zero volts.
پیشنهادی
Battery-Powered Measurement Circuit
Use the MCP601T-I/SN to amplify or buffer sensor signals in battery-operated measurement equipment where every microampere affects operating time. Its 230 uA typical operating current is the primary efficiency feature, while the 2.8 MHz gain-bandwidth product provides more bandwidth than required for many slow analog measurements. The single 2.7 V to 5.5 V supply simplifies system design, although a low-quiescent regulator and low-leakage sensor should be selected to maximize battery life.
پیشنهادی
Precision Current Sensing
The MCP601T-I/SN is suitable for amplifying the small differential voltage produced by a current-sense shunt. Its less-than-2 mV typical input offset helps preserve low-level measurements, and unity-gain stability supports direct voltage feedback around the amplifier. The rail-to-rail output can increase the usable signal range in a 2.7 V or 3.3 V system. Layout should keep the sense-pair traces short and matched so shunt drop and copper resistance do not obscure the measurement.
پیشنهادی
Active Audio Input Stage
The MCP601T-I/SN can serve as a modest audio input buffer when the design does not require high-voltage output swing or very low distortion specifications. Its 2.8 MHz gain-bandwidth product provides bandwidth for voice-band and limited full-range audio paths, while the 230 uA typical operating current suits portable and space-constrained equipment. Place a suitable coupling capacitor at the input, keep the input return path short, and verify that the selected gain does not create excessive noise-gain amplification.
پیشنهادی
Industrial Threshold Detection
The MCP601T-I/SN can compare a sensor or control signal against a reference in industrial threshold-detection circuits. Its less-than-2 mV typical input offset is useful when the difference between the input and reference is small, while the common-mode input range extending below ground permits operation near zero volts. The 8-pin SOIC package simplifies conventional PCB assembly. Use a clean reference, provide local supply bypassing, and account for input and output propagation delay where timing margins are important.
پیشنهادی
Low-Frequency Active Filter
The MCP601T-I/SN is appropriate for first-order and moderate-order active-filter stages operating within its 2.8 MHz gain-bandwidth capability. Its unity-gain stability supports closed-loop gain settings around one, and the rail-to-rail output increases the available signal swing on a 2.7 V to 5.5 V supply. Component tolerances and the amplifier's finite gain-bandwidth response determine the practical filter response, so simulation should include realistic capacitance and resistance values before the circuit is released for production.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای MCP601T-I/SN — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | MCP601T-E/SN | MCP601-I/SN |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Amplifier Configuration | Single operational amplifier | Single operational amplifier | Single operational amplifier |
| Gain-Bandwidth Product | 2.8 MHz | 2.8 MHz | 2.8 MHz |
| Typical Operating Current | 230 uA | 230 uA | 230 uA |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Typical Input Offset Voltage | <2 mV | <2 mV | <2 mV |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Unity-Gain Stable | Yes | Yes | Yes |
تفاوتهای کلیدی
- Low-power operation with useful moderate bandwidth (در مقابلMCP601T-E/SN)
- Single-amplifier footprint without dual-channel pin changes (در مقابلMCP6002T-I/SNVAO)
- Rail-to-rail output for low-voltage systems (در مقابلMCP601-I/SN)
یادداشتهای طراحی
Place the input, feedback, and bypass components close to the MCP601T-I/SN pins. Keep the inverting and non-inverting traces short and away from high-current switching paths. If the input source has high impedance, minimize leakage from board contamination and guard the input node when practical. These layout practices reduce parasitic capacitance, stabilize the closed-loop response, and limit injected noise.
Add local VDD-to-VSS bypass capacitance near the amplifier and use separate routing for supply current and sensitive signal returns. The MCP601T-I/SN requires a 2.7 V to 5.5 V supply, so confirm that supply noise does not force the output beyond the usable rail-to-rail region. For battery-powered designs, include the amplifier's 230 uA typical operating current in the standby and active power budgets.
Do not assume that rail-to-rail output eliminates all headroom requirements. Verify the output waveform at the required frequency, load, supply voltage, and temperature because output swing and drive capability depend on operating conditions. Also avoid placing the non-inverting input directly beside the output in a voltage follower; even a small parasitic coupling path can reduce stability or distort the result.
اطلاعات انطباق
The manufacturer product page and family datasheet do not establish the requested compliance statuses in the accessed material. The AEC-Q100 reference shown for the orderable listing was not treated as qualification evidence for the standard-temperature MCP601T-I/SN without a corresponding Microchip qualification statement.