MCP6022-I/ST - Dual 10 MHz Rail-to-Rail Op Amp | Microchip
MPN: MCP6022-I/ST ✓ فعالMCP6022-I/ST نمای کلی
An operational amplifier, commonly called an op amp, is a voltage-controlled differential amplifier that uses feedback to amplify the difference between two input voltages. The MCP6022 belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors. Its dual configuration provides two amplifiers in one package, allowing one device to serve two independent signal paths while reducing board area and package count.
Key features include rail-to-rail input and output operation, a 10 MHz gain-bandwidth product, low offset voltage below 0.5 mV, and low typical operating current of 1.0 mA. The rail-to-rail output swing is particularly useful in low-voltage systems because it allows the amplifier to approach the supply rails more closely than a conventional output stage. Low bias current supports high-impedance source connections, while the CMOS implementation provides high open-loop gain and low power consumption.
The MCP6022 uses Microchip's advanced CMOS technology to combine low bias current, high-speed operation, high open-loop gain, and rail-to-rail output swing. Its 10 MHz bandwidth makes it suitable for signal-conditioning stages that require more bandwidth than a general-purpose low-frequency amplifier while maintaining a relatively low 1.0 mA typical operating current. The dual amplifier architecture supports independent channels or a differential amplifier arrangement.
Typical applications include low-voltage sensor conditioning, current-feedback instrumentation, audio signal processing, active filtering, and general-purpose analog signal amplification. Two amplifiers in one 8-lead TSSOP can simplify designs requiring matched channels, such as stereo audio preamplification, dual-axis sensor interfaces, or differential-to-single-ended conversion. Supply and decoupling requirements must still be evaluated for each operating point.
The primary design consideration is system-level power and stability planning. Keep the input common-mode voltage and output swing within the operating limits described by the manufacturer datasheet, and place the supply bypass capacitor close to the positive and ground pins. Because the device is intended for low-voltage operation, verify that signal amplitudes and output loads remain compatible with the selected supply voltage.
This page organizes the manufacturer specifications, package information, application guidance, and verified drop-in alternatives for faster engineering evaluation. For a proposed replacement, confirm pin assignment, electrical limits, temperature grade, stability, and the target circuit's gain and loading before approving a PCB substitution.
جایگزینهای drop-in برای MCP6022-I/ST — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای MCP6022-I/ST (همان فرمفاکتور و فوتپرینت) — متفاوت در Amplifier Type, Package, Typical Operating Current.
MCP6002-I/ST
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
MCP6022-E/ST
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
MCP6022-I/ST حداکثر مقادیر مجاز و مشخصات الکتریکی
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Amplifiers | 2 amplifiers |
| Gain-Bandwidth Product | 10 MHz |
| Typical Operating Current | 1.0 mA per amplifier |
| Maximum Quiescent Current | Less than 1.35 mA per amplifier |
| Input Offset Voltage | Less than 0.5 mV |
| Minimum Single-Supply Voltage | 2.5 V |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Technology | Advanced CMOS |
| Bias Current | Low |
| Open-Loop Gain | High |
| بستهبندی | 8-lead TSSOP |
| نوع نصب | Surface mount |
| Product Type | Standard general-purpose amplifier |
پیکربندی پین MCP6022-I/ST
| پین 1 | OUTA — Amplifier A output |
| پین 2 | IN A- — Inverting input for amplifier A |
| پین 3 | IN A+ — Non-inverting input for amplifier A |
| پین 4 | V- — Negative power supply or ground in single-supply operation |
| پین 5 | IN B+ — Non-inverting input for amplifier B |
| پین 6 | IN B- — Inverting input for amplifier B |
| پین 7 | OUTB — Amplifier B output |
| پین 8 | V+ — Positive power supply |
کاربردهای معمول
MCP6022-I/ST مناسب است برای 6 کاربردs: Low-Voltage Sensor Signal Conditioning, Stereo Audio Preamplification, Active Analog Filtering, Current Measurement Signal Path, Data Acquisition Front End, Industrial Control Signal Amplification.
Low-Voltage Sensor Signal Conditioning
The MCP6022-I/ST is suitable for conditioning sensor signals in compact, low-voltage systems because its single supply can be as low as 2.5 V and its input and output are rail-to-rail. The 10 MHz gain-bandwidth product provides more bandwidth than a slow precision-only amplifier, while the input offset voltage below 0.5 mV helps preserve small differential signals. Place the amplifier between the sensor and the following ADC or digital processing stage, and include close supply bypassing. Confirm that the sensor output stays within the amplifier's common-mode range and that the selected closed-loop gain remains stable with the sensor and ADC input capacitances.
پیشنهادی
Stereo Audio Preamplification
The dual MCP6022-I/ST can provide two independent low-voltage audio preamplifier channels in one 8-lead TSSOP package. Its rail-to-rail output swing is useful when the available supply voltage limits the usable output range, while the 10 MHz gain-bandwidth product provides useful bandwidth for audio-band signal paths. Both amplifiers operate from a supply as low as 2.5 V, and typical operating current is 1.0 mA per amplifier. Keep the two channels symmetrical when matching input impedances and gain networks, and verify output swing, load impedance, and distortion requirements against the manufacturer electrical characteristics.
پیشنهادی
Active Analog Filtering
The MCP6022-I/ST fits active filter stages requiring more bandwidth than a low-speed general-purpose amplifier. Its 10 MHz gain-bandwidth product allows useful closed-loop gain to remain available across higher signal frequencies, while rail-to-rail input and output behavior supports low-amplitude filter nodes supplied from a 2.5 V rail or above. Use the amplifier in the standard inverting or non-inverting topology and calculate resistor and capacitor tolerances around the required frequency response. Confirm loop gain, phase margin, output loading, and power-supply rejection in the final filter because the manufacturer data identifies the device as a low-power CMOS operational amplifier.
پیشنهادی
Current Measurement Signal Path
The MCP6022-I/ST can amplify the differential voltage generated by a current-sense network in low-voltage power instrumentation. Rail-to-rail input operation helps use the available signal range, and the less-than-0.5 mV input offset specification limits the amplifier's inherent contribution when the sensed voltage is small. The 10 MHz gain-bandwidth product is suitable for measurement paths that need reasonable bandwidth beyond DC. Position the amplifier close to the sense network, maintain a low-impedance reference return, and avoid placing high-gain circuitry where it can amplify switching-node noise. The load and common-mode limits must remain within the manufacturer electrical limits.
پیشنهادی
Data Acquisition Front End
The dual MCP6022-I/ST can provide two low-power analog channels ahead of an ADC in a compact data-acquisition design. Operation from a single supply as low as 2.5 V supports low-voltage sensor systems, while rail-to-rail input and output operation improves utilization of the available signal range. The 10 MHz gain-bandwidth product is useful when each channel requires bandwidth beyond a static-DC measurement, and typical operating current of 1.0 mA per amplifier supports power-constrained instrumentation. Check the ADC input range, acquisition time, drive requirements, and the amplifier's output swing. Add local supply decoupling and keep high-impedance input nodes physically short to reduce sensitivity to stray capacitance and leakage.
پیشنهادی
Industrial Control Signal Amplification
The MCP6022-I/ST is applicable to low-level control and instrumentation signals where a dual amplifier provides two channels without using two separate packages. Its rail-to-rail input and output behavior is advantageous when the control system operates from a low-voltage rail, and the 10 MHz gain-bandwidth product supports signals beyond very-low-frequency operation. Typical operating current of 1.0 mA per amplifier is useful in distributed or battery-powered industrial equipment. Confirm the industrial ambient-temperature requirement, transient environment, grounding strategy, and output load for each channel. Stable feedback-network layout and close placement of the supply bypass capacitor are important when the source impedance is high or the signal path is fast.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای MCP6022-I/ST — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | MCP6002-I/ST | MCP6022-E/ST |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-lead TSSOP | 8-lead TSSOP | 8-lead TSSOP |
| Number of Amplifiers | 2 amplifiers | 2 amplifiers | 2 amplifiers |
تفاوتهای کلیدی
- Higher bandwidth than the lower-bandwidth same-package alternative (در مقابلMCP6002-I/ST)
- Rail-to-rail signal operation from a low-voltage supply (در مقابلMCP6002-I/ST)
- Low offset and operating current in a dual package (در مقابلMCP6022-E/ST)
یادداشتهای طراحی
Decouple the positive supply and ground pins locally with the capacitor configuration specified by the manufacturer. Keep the connection from the bypass capacitor to the device short because trace inductance can reduce high-frequency supply rejection. The MCP6022-I/ST supports single-supply operation from 2.5 V, but the selected rail must still provide adequate output swing for the required signal amplitude and load. Do not infer output capability from supply voltage alone.
Do not treat the 8-lead TSSOP footprint as proof that every dual amplifier is electrically interchangeable. MCP6002-I/ST uses the same package but has a different bandwidth profile, while a device with shutdown or enable logic may assign a package pin differently. Compare the manufacturer pin-description table, common-mode limits, output swing, slew behavior, and stability requirements before treating a candidate as a drop-in replacement.
Keep each feedback component close to its corresponding amplifier channel and route the inverting input as a short loop on the PCB. For high-impedance sensors, minimize the length of input traces and avoid running them beside switching nodes or high-current return paths. The two amplifier channels share a package and supply but should use symmetric grounding and decoupling arrangements when matched behavior is important.
The 10 MHz gain-bandwidth product makes feedback topology and board parasitics more important than they would be in a very slow precision amplifier. Confirm closed-loop stability for the intended gain with the actual source resistance, load, and output capacitance. If the circuit drives an ADC or sampling network, evaluate settling requirements and keep the amplifier output connection short to minimize coupling into the sampling node.
اطلاعات انطباق
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration for MCP6022-I/ST was identified in the available manufacturer and distributor information.