MCP602T-I/SN - Dual 2.8 MHz Rail-to-Rail CMOS Op Amp
MPN: MCP602T-I/SN ✓ فعالMCP602T-I/SN نمای کلی
An operational amplifier is a voltage-gain stage used to amplify, buffer, filter, or compare small differential signals. The MCP602 belongs to the CMOS operational-amplifier hierarchy, combining rail-to-rail input and output behavior with low power consumption. This makes it useful when the signal must be processed close to its source without adding substantial supply-current overhead.
The MCP602 family provides two amplifiers in one 8-pin SOIC package. Its 2.8 MHz gain-bandwidth product supports moderate-frequency closed-loop operation, while the 230 uA typical operating current supports battery-powered and portable equipment. Rail-to-rail output swing increases usable output range, and the typical input offset voltage below 2 mV supports precision-oriented signal conditioning.
Microchip’s CMOS implementation provides low input bias current and high open-loop gain while maintaining a low typical operating current. The dual configuration reduces package count when two independent analog channels are required. Because the amplifier operates from a single supply, it also fits systems where a negative supply is unavailable or undesirable.
Typical uses include low-power sensor conditioning, general-purpose voltage buffering, audio and instrumentation signal stages, active filtering, and low-frequency control loops. The 2.8 MHz gain-bandwidth product is appropriate for moderate-bandwidth analog paths rather than high-speed video or RF amplification.
When designing a PCB around the MCP602T-I/SN, keep feedback components and bypass capacitance close to the relevant pins, maintain a common ground reference between the two channels, and check output-drive requirements at the selected supply voltage and load. These practices reduce parasitic feedback and preserve the expected closed-loop response.
This product page combines manufacturer specifications, package and pinout guidance, application analysis, and engineering-focused alternatives. It is intended to help designers evaluate the MCP602T-I/SN quickly while retaining the datasheet as the controlling document for ratings, limits, and production implementation.
جایگزینهای drop-in برای MCP602T-I/SN — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای MCP602T-I/SN (همان فرمفاکتور و فوتپرینت) — متفاوت در Gain-Bandwidth Product, Package, Typical Operating Current.
MCP602T-E/SN
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←MCP6022T-I/SN
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MCP6023T-I/SN
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MCP6002T-I/SN
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MCP6002T-E/SN
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
MCP602T-I/SN حداکثر مقادیر مجاز و مشخصات الکتریکی
| Number of Amplifiers | 2 amplifiers |
| Gain-Bandwidth Product | 2.8 MHz |
| Typical Operating Current | 230 uA per amplifier |
| Typical Input Offset Voltage | Less than 2 mV |
| Supply Voltage Range | 2.7 V to 6.0 V |
| Technology | CMOS |
| Output Swing | Rail-to-rail |
| Input Bias Current | Low bias current |
| Open-Loop Gain | High open-loop gain |
| تعداد پینها | 8 pins |
| بستهبندی | 8-pin SOIC |
| نوع نصب | Surface mount |
راهنمای پیکربندی پین MCP602T-I/SN 8-pin soic
پیکربندی پین برای MCP602T-I/SN (پکیج 8-pin soic). این قطعه آنالوگ دارای پینهای ورودی، خروجی و تغذیه است. برای پیکربندیهای پین offset null، جبرانسازی و فعالسازی به دیتاشیت سازنده مراجعه کنید. ایدهآل برای مدارهای شرطیسازی سیگنال و تقویتکننده.
داده پینآوت تفصیلی موجود نیست برای MCP602T-I/SN.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
MCP602T-I/SN مناسب است برای 6 کاربردs: Battery-Powered Sensor Conditioning, Portable Audio Signal Buffering, Industrial Instrumentation Amplification, Active Filtering and Control Loops, Low-Power Voltage Comparison, Compact Interface Buffering.
Battery-Powered Sensor Conditioning
The MCP602T-I/SN fits low-power sensor front ends because each amplifier draws 230 uA typical operating current while providing a 2.8 MHz gain-bandwidth product. Place the dual channels around sensor outputs for buffering and gain shaping without introducing a separate amplifier for each signal. The 2.7 V to 6.0 V supply range supports battery-powered electronics, while rail-to-rail output swing increases the usable signal range in compact systems. Before finalizing the circuit, verify the sensor output against the amplifier input common-mode range and confirm that the selected gain produces acceptable phase margin at the operating frequency.
پیشنهادی
Portable Audio Signal Buffering
The MCP602T-I/SN is suitable for audio preamplifier and buffering stages where low supply current and rail-to-rail output swing are important. Its 2.8 MHz gain-bandwidth product provides more closed-loop bandwidth than a 1 MHz low-power stage, while the 230 uA typical operating current per channel limits supply demand in portable equipment. The two amplifiers can support independent left and right paths or separate control and monitoring functions. Set the closed-loop gain and feedback-network values against the required audio bandwidth, and verify output swing into the next stage with realistic load and output-voltage conditions.
پیشنهادی
Industrial Instrumentation Amplification
The MCP602T-I/SN can provide input buffering and gain stages for low-frequency industrial instrumentation signals. Its typical offset voltage below 2 mV supports accurate signal conditioning, while the 2.8 MHz gain-bandwidth product accommodates higher closed-loop gains better than a 1 MHz general-purpose dual amplifier. The dual 8-pin SOIC device also allows two measurement channels to share a compact board area. For instrumentation use, check input bias current, common-mode range, noise, output drive, and the input protection network, because sensor interfaces can impose requirements beyond basic gain and bandwidth.
پیشنهادی
Active Filtering and Control Loops
The MCP602T-I/SN is appropriate for active filters and low-frequency control loops that require more bandwidth than the MCP6002 family’s 1 MHz gain-bandwidth product. At 2.8 MHz, the device supports closed-loop operation at frequencies that are useful for audio-adjacent signal shaping, sensor conditioning, and modest control loops. Both channels can implement Sallen-Key or related active-filter sections when component tolerances and noise are handled carefully. Evaluate each filter stage for noise gain, phase margin, component tolerance, and output-load stability rather than selecting the gain-bandwidth value alone.
پیشنهادی
Low-Power Voltage Comparison
The MCP602T-I/SN can implement dual voltage comparators or threshold detectors when open-loop operation is stable under the chosen conditions. The dual architecture fits battery monitoring, control thresholds, and discrete sensor-alarm functions without requiring two separate amplifier packages. Its typical operating current of 230 uA per channel supports low-power monitoring, while the 2.8 MHz gain-bandwidth product provides response capability beyond a 1 MHz comparator-like substitute. Add hysteresis to prevent repeated switching near the threshold, and use pull-up or pull-down arrangements that remain valid for the selected output voltage and supply range.
پیشنهادی
Compact Interface Buffering
The MCP602T-I/SN is useful for buffering outputs from slow sensors, converters, or digital control lines before they enter a higher-impedance measurement chain. Low bias current reduces loading on the source, rail-to-rail output swing preserves signal range in low-voltage systems, and the 2.8 MHz gain-bandwidth product gives more bandwidth than the MCP6002T-I/SN option. The dual package supports two buffered signals in one 8-pin SOIC. Confirm the source impedance, capacitive load, output settling requirements, and stability configuration, especially if the connected source includes long PCB traces or slow edges.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای MCP602T-I/SN — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | MCP602T-E/SN | MCP6022T-I/SN | MCP6023T-I/SN | MCP6002T-I/SN | MCP6002T-E/SN |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Number of Amplifiers | 2 | 2 | 2 | 2 | 2 | 2 |
تفاوتهای کلیدی
- Higher gain-bandwidth product than the MCP6002 family (در مقابلMCP6002T-I/SN)
- Closest same-family ordering alternative (در مقابلMCP602T-E/SN)
- Dual-channel integration reduces package count (در مقابلMCP601)
یادداشتهای طراحی
Place the input, output, feedback, and supply-bypass components close to their associated MCP602T-I/SN pins. Keep each amplifier’s feedback loop physically small to minimize parasitic capacitance and the chance of oscillation at higher closed-loop gains. Route the two channels to maintain consistent grounding and return paths. If the PCB uses long sensor traces, keep those nets away from the power pins and amplifier inputs because coupled noise can appear directly as input-referred error.
Calculate amplifier supply demand using worst-case operating current rather than the 230 uA typical value when sizing the battery or regulator. The dual device contains two amplifiers, so a system that keeps both channels active can draw approximately twice the per-amplifier current before load and supply-voltage effects. The stated 2.7 V to 6.0 V operating range must include tolerance and transient margin. Also verify that the source can support the output swing and capacitive load required by the downstream stage.
Choose the closed-loop gain and feedback resistor values with the 2.8 MHz gain-bandwidth product in mind. Higher noise gain reduces bandwidth and phase margin, so a unity-gain configuration offers substantially more bandwidth than a high-gain stage. For capacitive loading, avoid relying on gain alone to create stability; consult the family guidance and add isolation resistance when the next stage presents excessive capacitance. Confirm settling behavior with the actual source impedance, load, and PCB parasitics.
Do not assume that rail-to-rail output swing guarantees a rail-to-rail input common-mode range. Check input bias current, input voltage range, output load, and absolute maximum limits for the selected supply. For comparator-style operation, add positive feedback hysteresis to avoid output chatter near the threshold. When replacing the device, verify that the alternative has the same amplifier-channel pin functions and operating area rather than comparing package names alone.
اطلاعات انطباق
Compliance status is not stated in the manufacturer product-page excerpt or the other cited product records. Verify the current declarations and material-category documentation with Microchip before release.