Texas Instruments

OPA4137P - Quad 36V 1MHz FET Op Amp | Texas Instruments

MPN: OPA4137P ✓ فعال
36 V Vdss Approximately 10 pA for the OPA137 series Id 14-pin PDIP Package
حداقل سفارش: 1 |

OPA4137P نمای کلی

The Texas Instruments OPA4137P is a four-channel, J-FET-input operational amplifier with rail-to-rail input capability, a 1 MHz gain-bandwidth product, and a 3.5 V/µs slew rate, packaged in a 14-pin PDIP. It operates from ±2.25 V to ±18 V, giving the device a 36 V maximum total supply range for precision analog signal-chain designs that require low input bias current and broad supply-voltage flexibility.

An operational amplifier is a high-gain differential amplifier used to amplify voltage differences while providing feedback-defined gain, filtering, buffering, or signal conditioning. The OPA4137 belongs to the FET-input operational-amplifier family within the broader analog IC and power-management signal-chain hierarchy. Its four amplifiers share a common package while providing independent channels for instrumentation, converters, and active filtering.

The OPA4137P uses low-input-bias-current J-FET input stages, making it suitable for high-impedance sources that would load conventional bipolar transistor inputs. The series documentation identifies input bias current around 10 pA, quiescent current around 120 µA per channel, and open-loop gain around 145 dB for applicable family configurations. The 1 MHz gain-bandwidth product supports moderate-bandwidth precision applications rather than high-speed video or RF signal chains.

Each channel combines low-noise J-FET inputs with a 3.5 V/µs slew rate. The family is intended for low-cost and miniature applications where low bias current, low quiescent current, and compact implementation are important. Because all four channels are integrated into one 14-pin PDIP, designers can reduce external interconnections in multi-channel filters, sensor front ends, and signal-conditioning boards.

Typical applications include low-frequency precision filters, current-to-voltage conversion, audio and instrumentation signal conditioning, sensor amplification, and analog control loops. It is particularly appropriate when source impedances are high enough that input bias current could create an unacceptable DC error. It is less suitable for demanding high-speed, high-output-current, or unity-gain-stable high-voltage applications without careful review of the complete electrical characteristics.

For PCB implementation, place each bypass capacitor close to the associated supply pins, keep feedback components close to their channel pins, and provide a quiet ground reference. Avoid long high-impedance traces because leakage, contamination, and parasitic capacitance can degrade the low-bias-current advantage. Confirm output swing, input common-mode range, noise, distortion, and stability against the actual gain and load before releasing the design.

This page combines manufacturer specifications, package and pin information, sourcing guidance, verified cross-reference results, and practical design notes. It also identifies where an alternative requires explicit engineering review rather than assuming that a similar amplifier function guarantees a board-level drop-in replacement.

جایگزین‌های drop-in برای OPA4137P — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای OPA4137P (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Input Bias Current, Open-Loop Gain, Quiescent Current.

Texas Instruments
Input Bias Current: 1 pA
Open-Loop Gain: 115 dB typical
Quiescent Current: 20 uA per amplifier typical
مقایسه با OPA4137P →

OPA4990IP

✅ جایگزین مستقیم
📦 14-pin PDIP
Maximum total supply voltage increases from 36 V to 40 V, while gain-bandwidth product increases from 1 MHz to 1.1 MHz; TI identifies the device as a drop-in upgrade.

📋 جایگزین مرجع (خارج از کاتالوگ)

OPA336P

✅ جایگزین مستقیم
Texas Instruments
📦 14-pin PDIP
Single operational amplifier · 1 channel · 20 uA per amplifier typical · 125 uV maximum · 1 pA · 115 dB typical · Single supply · Rail-to-rail input

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

OPA4342PA

✅ جایگزین مستقیم
📦 14-pin PDIP
The cited comparison reports matching primary technical parameters; package dimensions, pin assignments, bias current, offset, and noise require confirmation before substitution.

📋 جایگزین مرجع (خارج از کاتالوگ)

OPA4137P حداکثر مقادیر مجاز و مشخصات الکتریکی

Number of Channels 4 channels
Amplifier Type J-FET-input operational amplifier
Maximum Total Supply Voltage 36 V
Supply Voltage Range ±2.25 V to ±18 V
Gain-Bandwidth Product 1 MHz
Slew Rate 3.5 V/µs
Input Bias Current Approximately 10 pA for the OPA137 series
جریان سکون Approximately 120 µA per channel for the OPA137 series
Open-Loop Gain Approximately 145 dB for the OPA137 series
Input Common-Mode Capability Rail-to-rail input
Package Type 14-pin PDIP
تعداد پایه 14 pins
نوع نصب Through-hole

پیکربندی پین OPA4137P

DIP-14 Package Pinout Diagram DIP-14 14-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 DIP-14
پین 1 OUTA — Amplifier A output
پین 2 INA- — Amplifier A inverting input
پین 3 INA+ — Amplifier A non-inverting input
پین 4 V+ — Positive supply connection
پین 5 INB+ — Amplifier B non-inverting input
پین 6 INB- — Amplifier B inverting input
پین 7 OUTB — Amplifier B output
پین 8 OUTC — Amplifier C output
پین 9 INC- — Amplifier C inverting input
پین 10 INC+ — Amplifier C non-inverting input
پین 11 V- — Negative supply connection
پین 12 IND+ — Amplifier D non-inverting input
پین 13 IND- — Amplifier D inverting input
پین 14 OUTD — Amplifier D output

کاربردهای معمول

OPA4137P مناسب است برای 6 کاربردs: High-Impedance Sensor Signal Conditioning, Precision Active Filters, Current-to-Voltage Conversion, Audio and Instrumentation Buffering, Industrial Analog Control Loops, Low-Power Precision Analog.

🧩

High-Impedance Sensor Signal Conditioning

The OPA4137P suits low-frequency sensor amplifiers because its J-FET input stage provides approximately 10 pA bias current for the relevant OPA137 series configuration. That low current limits the input-voltage error created when source resistance is high. Place the amplifier close to the sensor connector and use guarding or a driven shield if contamination and cable leakage are significant. The 1 MHz bandwidth is ample for many resistive sensors but should be matched to the sensor bandwidth to avoid unnecessary noise amplification.

⚡

Precision Active Filters

The OPA4137P can implement multi-channel active filters where four matched amplifier sections simplify board area and reduce channel-count variations. Its 1 MHz gain-bandwidth product and 3.5 V/µs slew rate support low-frequency precision filtering, while the J-FET inputs reduce errors associated with high-value feedback networks. Component tolerances, resistor matching, and the amplifier's open-loop gain will influence filter accuracy. Verify the selected gain-bandwidth combination and capacitive loading in the manufacturer's stability guidance before fabrication.

📡

Current-to-Voltage Conversion

The OPA4137P is appropriate for transimpedance and current-to-voltage conversion stages where low input bias current helps preserve the accuracy of weak sensor currents. The approximately 10 pA input-bias-current characteristic for the applicable OPA137 series configuration reduces DC error across high feedback resistors. Use short guarded input paths, clean high-impedance PCB regions, and a carefully selected feedback capacitor. The 1 MHz gain-bandwidth product also places a practical ceiling on the achievable closed-loop bandwidth.

🎧

Audio and Instrumentation Buffering

Four independent OPA4137P channels can provide input buffering, gain stages, and balanced signal-conditioning paths in audio and instrumentation equipment. The approximately 120 µA per-channel quiescent current for the relevant OPA137 series configuration is useful in compact systems, while the 36 V maximum total supply rating supports conventional ±15 V or ±18 V laboratory rails. Confirm output swing into the intended load and evaluate distortion at the actual signal level. Feedback-network placement should minimize noise pickup and channel-to-channel coupling.

🏭

Industrial Analog Control Loops

The OPA4137P can implement low-frequency industrial control loops, error amplifiers, and actuator-signal interfaces when the source impedance is high and supply headroom is limited by the installation. Its ±2.25 V to ±18 V operating range supports split supplies common in industrial analog systems. Because the device is not a power amplifier, verify output current, output swing, capacitive-load behavior, and loop stability against the actuator interface. Add transient protection at exposed connectors and maintain separate return paths for high-current outputs.

📱

Low-Power Precision Analog

The OPA4137P suits portable measurement and control equipment where a four-channel low-power analog front end simplifies system design. The OPA137 series documentation identifies approximately 120 µA quiescent current per channel for applicable configurations, and the 3.5 V/µs slew rate is sufficient for many sensor signals and low-frequency control waveforms. Assess total supply current across all four channels and any downstream converters. For battery-powered operation, validate the complete rail range, output load, and duty cycle rather than relying on the no-load quiescent-current figure alone.

خلاصه محصولات پیشنهادی

OPA4137P Texas Instruments استفاده‌شده در: High-Impedance Sensor Signal Conditioning, Precision Active Filters, Current-to-Voltage Conversion, Audio and Instrumentation Buffering, Industrial Analog Control Loops, Low-Power Precision Analog OPA4137UA Same-family surface-mount option استفاده‌شده در: High-Impedance Sensor Signal Conditioning OPA2137UA Dual-channel family option for smaller filters استفاده‌شده در: Precision Active Filters, Audio and Instrumentation Buffering, Low-Power Precision Analog OPA137UA Texas Instruments استفاده‌شده در: Current-to-Voltage Conversion, Industrial Analog Control Loops
What are the key specifications of OPA4137P that engineers should know?
The OPA4137P is a four-channel J-FET-input operational amplifier with a 1 MHz gain-bandwidth product, 3.5 V/µs slew rate, rail-to-rail input capability, and a 36 V maximum total supply rating. According to the Texas Instruments OPA137 series datasheet, the family provides approximately 10 pA input bias current and 120 µA quiescent current per channel for applicable configurations. The OPA4137P is supplied in a 14-pin PDIP package and operates from ±2.25 V to ±18 V.
What is the operating voltage of OPA4137P?
The OPA4137P operates from ±2.25 V to ±18 V, equivalent to a 4.5 V to 36 V total supply range. According to the Texas Instruments OPA4137 product page and OPA137 series datasheet, this wide range permits conventional dual supplies, split rails, and single-supply operation where the input and output signals remain within the supported common-mode and output-swing limits. The 36 V figure is the maximum total supply voltage, not a single-polarity operating voltage.
What type of operational amplifier is the OPA4137P?
The OPA4137P is a four-channel J-FET-input operational amplifier. The Texas Instruments OPA137 series datasheet identifies low input bias current, low quiescent current, and high open-loop gain as family characteristics, making the device appropriate for high-impedance sources and precision analog signal conditioning. Unlike a power operational amplifier, the OPA4137P is intended for low-frequency signal-chain work rather than high-current loads or high-speed video amplification.
Where can I download the OPA4137P datasheet PDF?
The official OPA4137P documentation is available through the Texas Instruments OPA137 series datasheet page at https://www.ti.com/lit/gpn/OPA137, while the family product information is at https://www.ti.com/product/OPA4137. The series document covers OPA137, OPA2137, and OPA4137 devices. Use the package-specific pin configuration and ordering information to confirm the 14-pin PDIP variant before assigning PCB signals.
Where can I find the OPA4137P pinout?
The OPA4137P pinout is found in the Texas Instruments OPA137 series datasheet at https://www.ti.com/lit/gpn/OPA137. Its 14-pin PDIP uses four independent amplifier channels, common positive and negative supply pins, and paired differential inputs for each channel. When assigning PCB tracks, use the pin-description table in that document rather than relying on a generic quad-op-amp layout, because exposed-pad and thermal requirements can differ among package variants.
Is OPA4137P suitable for high-impedance sensor front ends?
Yes, the OPA4137P is well suited to high-impedance sensor front ends because its J-FET input stage provides approximately 10 pA input bias current for the relevant OPA137 series configuration. According to the Texas Instruments OPA137 series datasheet, this low bias current limits the DC error introduced by high source resistances. The amplifier still needs suitable electrostatic protection, guarding, clean connectors, and careful PCB layout to prevent leakage from degrading that advantage.
OPA4137P vs OPA4990IP - which is better for a precision analog circuit?
The OPA4137P is the better choice when low J-FET bias current and a 1 MHz gain-bandwidth product are the primary requirements, while the OPA4990IP provides an upgraded alternative rated for 40 V and 1.1 MHz operation according to the Texas Instruments product comparison. Both are presented as drop-in upgrade paths, but input bias current, supply limits, noise, output swing, and stability must be compared for the actual circuit. Confirm the exact OPA4990 package and channel pinout before PCB substitution.
What is the difference between OPA4137P and OPA336P?
The OPA336P and OPA4137P are identified as having identical primary performance parameters in the cited Xecor comparison, but they remain different amplifier families with different manufacturer documentation. The OPA4137P is explicitly specified as a four-channel J-FET-input amplifier with a 1 MHz gain-bandwidth product in the Texas Instruments OPA137 series documentation. Before using OPA336P as a drop-in replacement, verify its input bias current, offset, noise, common-mode range, output swing, and stability in the actual gain configuration.
When should I choose OPA4137P over OPA4990IP?
Choose OPA4137P when the design depends specifically on the OPA137 family's low-bias-current J-FET input stage and the circuit operates within a 36 V maximum total supply range. Choose OPA4990IP when the broader 40 V operating range or approximately 1.1 MHz gain-bandwidth product is useful and its other electrical characteristics better match the load. The decision should be based on full parameter review, not solely on matching the amplifier channel count and package.
What can replace OPA4137P?
The OPA4990IP is a documented Texas Instruments drop-in upgrade path for OPA4137, while the cited OPA336P comparison reports matching primary performance parameters. Neither result should be treated as an unconditional substitution: verify the exact package pins, supply rating, input common-mode range, output swing, offset voltage, noise, bias current, and gain stability. The OPA4137P is selected when its J-FET input behavior is required by a high-impedance source.
Is OPA4137P the same as OPA4342PA?
The OPA4137P and OPA4342PA are described by the cited Xecor comparison as having identical performance profiles across its primary technical parameters, but they are separate amplifier products and not identical devices. A board-level substitution also requires confirmation of package dimensions, lead spacing, channel pin assignments, and every limit condition relevant to the design. Review the manufacturer datasheets for both parts before approving OPA4342PA as a replacement.
What is the best Analog Devices equivalent for OPA4137P?
No Analog Devices equivalent can be confirmed as a true drop-in replacement from the cited cross-reference results. The OPA4137P is a four-channel, 14-pin PDIP J-FET amplifier, so a candidate must match the package and pinout as well as the 1 MHz bandwidth and low-bias-current requirement. Use the Texas Instruments cross-reference search and the Analog Devices product data to identify a specific qualified part; do not select solely by matching amplifier type and channel count.
Where to buy OPA4137P online?
Use the Request a Quote form on this page to request OPA4137P availability, current commercial terms, and lead time. The part is listed by Texas Instruments as an active product family member, while authorized distribution channels also list the 14-pin PDIP version. The Request a Quote workflow allows the exact MPN and required quantity to be checked without substituting a different package, temperature grade, or manufacturer status.
What is the price of OPA4137P?
Current OPA4137P commercial pricing depends on quantity, package, and market conditions and should be requested through the Request a Quote form on this page. No static price figure is presented because it can change without notice. Submit the exact OPA4137P MPN, target quantity, and shipment destination so the quote reflects the correct 14-pin PDIP configuration rather than a related OPA4137 package variant.
What is the lead time and stock status of OPA4137P?
The current stock position and lead time for OPA4137P should be confirmed through the Request a Quote form on this page. Texas Instruments lists the OPA4137 family as active, but family lifecycle status does not guarantee a fixed quantity for every package and order code. Request the exact OPA4137P MPN, quantity, and delivery schedule so the response reflects current manufacturing and distribution status.
How should OPA4137P be laid out for low leakage and low noise?
Place supply bypass capacitors close to the positive and negative supply pins, keep feedback resistors and compensation networks close to their associated channel, and minimize the length of high-impedance input traces. According to the Texas Instruments OPA137 series datasheet, the J-FET input stage has very low bias current, so board contamination and surface leakage can become significant error sources. Guarding and clean assembly practices can therefore matter as much as the nominal amplifier specification.

داده‌های مرجع مهندسی برای OPA4137P — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the OPA4137P when your circuit needs four low-power J-FET-input channels, approximately 10 pA input bias current, and a 36 V maximum total supply in a 14-pin PDIP package. It is especially useful for high-impedance sensors, transimpedance amplifiers, and precision filters where conventional bipolar input current would create significant DC error. Choose OPA4990IP when the design needs a 40 V rating or approximately 1.1 MHz bandwidth and its other parameters better satisfy the load and noise requirements. Consider OPA336P or OPA4342PA when the cited primary-parameter comparisons match the target, but verify input bias, offset voltage, noise, common-mode range, output swing, package dimensions, and gain stability before release. None of these substitutions should be approved from channel count and package name alone.

مقایسه با جایگزین‌ها

پارامتر این محصول OPA4990IP OPA336P OPA4342PA
Package 14-pin PDIP 14-pin PDIP 14-pin PDIP 14-pin PDIP
Brand Texas Instruments Texas Instruments Analog Devices Texas Instruments
Number of Channels 4 channels 4 channels 4 channels 4 channels

تفاوت‌های کلیدی

  • Lower-bias-current input architecture (در مقابلOPA4990IP)
  • Lower-voltage operating envelope for compact designs (در مقابلOPA4990IP)
  • Documented cross-family equivalence (در مقابلOPA336P)

یادداشت‌های طراحی

Place the positive and negative bypass capacitors as close as practical to the OPA4137P supply pins, and route them using short ground returns. For high-impedance inputs, keep the sensitive nodes away from switching nodes, inductors, relay contacts, and connector edges. The low input bias current of the J-FET input stage can be undermined by flux residue, conformal-coating contamination, or dirty board surfaces, so cleaning and guarding are important engineering controls.

Do not treat the 36 V rating as a ±36 V operating supply. The specified range is ±2.25 V to ±18 V, meaning the total voltage across the supply pins must remain within 36 V. Also verify rail-to-rail input operation at the selected common-mode voltage, output swing into the actual load, and closed-loop stability. The 1 MHz bandwidth and 3.5 V/µs slew rate do not by themselves guarantee stability at every gain or capacitive load.

For transimpedance and high-source-impedance designs, minimize input-node capacitance and use a feedback network selected for the intended closed-loop bandwidth. Keep the feedback resistor and compensation capacitor adjacent to the relevant channel. If the source is remote, consider guarding, a driven shield, or a nearby low-input-bias-current buffer. Validate leakage, settling time, and channel interaction on the actual board because connector and coating contamination can dominate the nominal amplifier error.

Estimate the amplifier's supply consumption from the approximately 120 µA per-channel family value plus output current and bias-current contributions, then apply a suitable margin for the complete circuit. Do not treat quiescent current as the total board demand. In single-supply systems, confirm that input bias, output swing, and common-mode range provide adequate headroom, and power the unused channels according to the datasheet's input-stage recommendations.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was identified for the exact OPA4137P ordering code. The product is an industrial instrumentation amplifier application rather than an AEC-Q100 automotive-qualified device.

تاریخ تأیید داده‌ها: 2026-11-14 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

OPA4137P datasheet OPA4137P datasheet pdf OPA4137P pinout OPA4137P 14-PDIP Texas Instruments OPA4137P OPA4137P equivalent OPA4137P replacement OPA4137P vs OPA4990IP OPA4137P price OPA4137P stock OPA4137P J-FET input amplifier OPA4137P high impedance sensor

قطعات و اصطلاحات مرتبط

Texas Instruments OPA4137P OPA4137 OPA137 OPA2137 OPA4990IP OPA336P OPA4342PA operational amplifier precision amplifier J-FET input rail-to-rail input input bias current gain-bandwidth product slew rate quiescent current high-impedance sensor transimpedance amplifier active filter signal conditioning 14-pin PDIP DIP package through-hole package precision analog
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ