PCA9564N - 400 kHz Parallel-to-I2C Controller | NXP
MPN: PCA9564N ✓ فعالPCA9564N نمای کلی
A parallel-to-I2C controller is an interface IC that translates data transactions between two different bus architectures. The parallel side presents a simple processor-oriented interface, while the I2C side provides standardized two-wire communication with sensors, memory devices, converters, and other peripherals. In the broader semiconductor hierarchy, the PCA9564N belongs to the interface-controller family within interface ICs and acts as a bridge between parallel microprocessor systems and serial bus devices.
The principal features of the PCA9564N include bidirectional parallel-bus operation, I2C controller functionality, and a maximum I2C transfer rate of 400 kHz. Bidirectional operation allows the controller to participate in transactions in which information must move between the parallel host and connected I2C devices. Its 400 kHz capability suits general-purpose industrial embedded-control systems that require faster transfer rates than standard 100 kHz I2C operation while retaining a compact peripheral-controller architecture.
The NXP manufacturer datasheet describes PCA9564N as a parallel-bus to I2C-bus controller. Its function is intended to simplify connection between parallel microprocessors and I2C devices without requiring each software stack to implement the complete bus conversion itself. Application-specific protocol overhead, addressing, interrupt handling, and timing behavior should be implemented and verified against the manufacturer pin-description and timing information before a production design is released.
Typical applications include industrial instrument panels, embedded control modules, legacy peripheral expansion, data-acquisition equipment, and board-level systems that retain a parallel processor interface while adding I2C sensors or memory. The 20-DIP package is particularly suitable for through-hole industrial assemblies and prototypes where leaded-package handling is preferred over fine-pitch surface-mount assembly.
For PCB implementation, follow the manufacturer datasheet pin-description table when assigning the parallel data lines, control signals, address inputs, clock, and I2C connections. Confirm pull-up requirements, decoupling, address selection, signal timing, and unused-pin treatment in the system schematic. Because the exact public pin map is not reproduced on this page, use the NXP datasheet as the authoritative source for board-layout signoff.
This product record combines the manufacturer product-page description, the 400 kHz interface rate, package information, application guidance, and a structured engineering comparison with practical implementation notes. These details help engineers determine whether PCA9564N fits a through-hole parallel-to-I2C bridging requirement before reviewing detailed timing, electrical limits, and ordering information in the manufacturer documentation.
جایگزینهای drop-in برای PCA9564N — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
PCA9564N,112
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
PCA9564
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
PCA9564N
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←PCA9564N مشخصات
| Product Type | Parallel bus to I2C-bus controller |
| Maximum I2C Transfer Rate | 400 kHz |
| Bidirectional Interface | Bidirectional parallel bus to I2C bus |
| Package Type | 20-pin DIP |
| Package Family | DIP family |
| نوع نصب | Through-hole |
| Number of Terminals | 20 terminals |
| Package Shape | Rectangular |
| Temperature Grade | Industrial |
راهنمای پیکربندی پین PCA9564N rectangular
پیکربندی پین برای PCA9564N (پکیج rectangular). شمارهگذاری پایهها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعملهای لحیمکاری به آن مراجعه کنید.
داده پینآوت تفصیلی موجود نیست برای PCA9564N.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
PCA9564N مناسب است برای 6 کاربردs: Industrial Sensor Interface Expansion, Legacy Parallel-System I2C Expansion, Data-Acquisition Front End, Instrument Panel and Human-Machine Interface, Embedded Memory and Peripheral Expansion, Board-Level System Upgrade.
Industrial Sensor Interface Expansion
PCA9564N fits industrial controller boards that retain a parallel microprocessor interface but need to add I2C-based sensors. The controller bridges the parallel host bus to the two-wire serial bus and supports transfer rates up to 400 kHz. Place it between the processor bus and shared I2C peripheral devices, then implement sensor commands, address decoding, and error recovery in firmware. Its 20-pin through-hole DIP package supports leaded industrial assembly methods. Before layout release, verify pin assignment, voltage levels, address selection, bus pull-ups, and timing against the NXP manufacturer datasheet.
Legacy Parallel-System I2C Expansion
Use PCA9564N when an established parallel-bus controller needs access to serial peripherals without replacing the host processor architecture. The bidirectional parallel-to-I2C controller allows bus transactions to pass between the processor and attached I2C components at rates up to 400 kHz. This approach can shorten hardware-development effort by reusing a familiar parallel interface while adding modern serial sensors or memory. The 20-DIP through-hole format is useful for legacy chassis and industrial boards assembled with conventional through-hole processes. Confirm protocol timing, reset behavior, and unused-pin treatment in the manufacturer documentation.
Data-Acquisition Front End
PCA9564N can provide the communication bridge between a parallel data-acquisition controller and I2C measurement peripherals. Supporting up to 400 kHz gives the design enough bus bandwidth for many moderate-rate sensor and converter transactions. Engineers can organize firmware around device addressing, command writes, and sequential data reads while retaining the processor's parallel bus interface. The through-hole 20-pin DIP package is suitable for instrument prototypes and industrial control cards. Validate acquisition timing, signal settling, pull-up values, and grounding with the application schematic and NXP timing data before production release.
Instrument Panel and Human-Machine Interface
PCA9564N is suited to instrument panels that combine a legacy parallel control processor with I2C display drivers, key controllers, or configuration peripherals. The bidirectional controller allows the host processor to exchange commands and status data with serial devices while maintaining a straightforward parallel-bus connection. Its 400 kHz transfer rate supports many control-oriented peripheral transactions, and the 20-DIP package facilitates through-hole assembly and serviceable industrial hardware. Design the firmware to separate bus arbitration, peripheral addressing, and display updates, and verify all signal levels and timing in the manufacturer datasheet.
Embedded Memory and Peripheral Expansion
PCA9564N can connect a parallel processor subsystem to I2C EEPROM, serial memory, converters, and other compact peripherals. The 400 kHz maximum transfer rate is suitable for moderate-volume configuration data and routine control traffic, while the bidirectional interface keeps the host-side connection independent of the I2C wire protocol. Use address pins or firmware-defined device selection as directed by the NXP datasheet, and account for pull-up resistors and bus capacitance on the shared I2C segment. The 20-pin DIP package is practical for industrial boards and prototypes where surface-mount conversion would add unnecessary layout work.
Board-Level System Upgrade
PCA9564N offers a practical upgrade path for boards that need modern I2C peripherals while retaining a parallel microprocessor interface. Instead of designing a separate serial-to-parallel subsystem, the device provides a defined controller function with operation up to 400 kHz. It can support staged development of new sensor, memory, or communication options without replacing the existing host logic. Because the package is a 20-pin through-hole DIP, designers should compare its mechanical footprint with the target board and preserve access for inspection and rework. Confirm logic thresholds, timing margins, address mapping, and power requirements before fabrication.
دادههای مرجع مهندسی برای PCA9564N — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول |
|---|---|
| Product Type | Parallel bus to I2C-bus controller |
| Bidirectional Interface | Yes |
| Maximum I2C Transfer Rate | 400 kHz |
| Package | 20-pin DIP |
| Brand | NXP Semiconductors |
| Mounting Type | Through-hole |
| Temperature Grade | Industrial |
| Number of Terminals | 20 terminals |
| Package Shape | Rectangular |
یادداشتهای طراحی
Assign every one of the 20 PCA9564N leads directly from the NXP manufacturer datasheet pin-description table, including address inputs, control signals, clock, ground, supply, and the I2C lines. Preserve the package orientation and lead spacing shown by the NXP mechanical drawing. Do not infer unused-pin treatment from generic DIP conventions because an electrically unused input can still require a defined bias in the system design.
Do not treat PCA9564D,118 as a drop-in replacement for PCA9564N. The PCA9564N uses a 20-pin through-hole DIP, whereas PCA9564D,118 is a 20-pin TSSOP surface-mount option. Although both are associated with the parallel-to-I2C controller family, changing package technology requires a PCB redesign and a fresh review of land patterns, assembly process, pin orientation, and electrical compatibility.
Design the shared I2C segment for the peripheral population and cable or PCB length. Add the pull-up network where required by the manufacturer's interface guidance, place it within the electrical reach of the bus, and check rise-time behavior at the maximum 400 kHz operating rate. Keep the parallel data and control routes away from sensitive analog inputs to reduce coupling into the sensor or converter interface.
Verify the PCA9564N logic supply range, input thresholds, output levels, and current consumption in the NXP manufacturer datasheet before assigning rails. Decouple the supply close to the device with the capacitance recommended by the datasheet, and provide compatible levels to every connected parallel and I2C peripheral. Mixed 2.5 V and 3.3 V systems require level review rather than assuming direct compatibility.
اطلاعات انطباق
The verified product information identifies an industrial-temperature-grade interface IC but does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to this industrial interface controller unless the manufacturer later designates a qualified automotive variant.