S912ZVC96F0MLF - 96KB Flash S12Z MagniV 16-bit MCU | NXP
MPN: S912ZVC96F0MLF ✓ فعالS912ZVC96F0MLF نمای کلی
An S12Z microcontroller is a 16-bit member of the NXP HC12/S12 architecture family, often classed within the broader automotive microcontroller and embedded MCU taxonomies (low-end automotive MCU -> body-domain ECU MCU -> S12 MagniV family). The MagniV line specifically integrates the voltage regulator and physical-layer LIN transceiver on-chip, eliminating external LIN transceivers and external supply regulators to reduce the BOM and shrink PCB area for body-electronics modules.
Key headline features include 96 KB (96K x 8) program Flash, 8 KB SRAM, a 32 MHz maximum CPU frequency with a 32 MHz bus clock, a 10-channel 10-bit SAR ADC, an integrated 5V linear regulator, a LIN 2.x/SCI physical layer, multiple timers (TIM, RTI, PIT), PWM channels, and a peripheral set covering GPIO, SPI, and SCI for in-vehicle networking. The RWW (Read-While-Write) Flash allows EEPROM emulation without an external serial EEPROM.
Architecture is built around the 16-bit S12Z enhanced CPU with extended address space, hardware stack pointer handling, and BGND debug; the device integrates high-voltage analog inputs (5V/12V-tolerant), EEPROM at 2 KB, and a -40 to +125C AEC-Q100 grade-1 qualified operating range. The 48-LQFP footprint is shared across the ZV/ZC MagniV family variants, allowing pin-compatible upgrades across memory sizes.
Typical applications include automotive HVAC door modules, seat controllers, window lift and door mirror modules, body-control slaves (LIN nodes), instrument cluster auxiliary circuits, and other body-domain ECUs. The integrated LIN and 5V regulator simplify LIN slave design versus discrete LIN MCU + external transceiver solutions.
When designing with this device, ensure adequate decoupling (>=100 nF plus >=4.7 uF bulk) near the integrated regulator output, dedicate a star-ground connection between ADC analog ground and digital ground, and respect LIN bus load impedance requirements per the LIN 2.x specification. AEC-Q100 grade-1 qualification at -40 to +125C makes the part directly suitable for under-hood and door-module placements.
جایگزین‌های drop-in برای S912ZVC96F0MLF — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای S912ZVC96F0MLF (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Core, Series, ADC, Package, Program Memory Size.
S912ZVCA19F0MLFR
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
S912ZVC12F0MLF
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←E912ZVC96F0MLF
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
S912ZVC64F0MLF
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
S912ZVC19F0MLF
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
S912ZVC96F0MLF حداکثر مقادیر مجاز و مشخصات الکتریکی
| Series | MagniV S12Z |
| Core | S12Z (16-bit) |
| Program Memory (Flash) | 96 KB (96K x 8) |
| RAM Size | 8 KB |
| EEPROM (emulated) | 2 KB |
| Maximum CPU Frequency | 32 MHz |
| Bus Clock | 32 MHz |
| Supply Voltage (Vdd) | 5 V (integrated regulator), wide external supply tolerance per datasheet |
| ADC | 10-ch, 10-bit |
| LIN Physical Layer | Integrated LIN 2.x / SCI transceiver |
| دمای کاری | -40C to +125C (AEC-Q100 Grade 1) |
| بسته‌بندی | 48-LQFP (7x7 mm), LFQFP |
| نوع نصب | Surface Mount |
| Terminal Form | Gull Wing |
| AEC-Q100 | Qualified (Automotive) |
پیکربندی پین S912ZVC96F0MLF
| پین 1 | PAD15/AN15 — High-voltage analog / digital I/O (port AD) |
| پین 2 | PAD14/AN14 — High-voltage analog / digital I/O |
| پین 3 | PAD13/AN13 — High-voltage analog / digital I/O |
| پین 4 | PAD12/AN12 — High-voltage analog / digital I/O |
| پین 5 | PAD11/AN11 — High-voltage analog / digital I/O |
| پین 6 | PAD10/AN10 — High-voltage analog / digital I/O |
| پین 7 | PAD09/AN9 — Analog input 9 / digital I/O |
| پین 8 | PAD08/AN8 — Analog input 8 / digital I/O |
| پین 9 | PAD07/AN7 — Analog input 7 / digital I/O |
| پین 10 | PAD06/AN6 — Analog input 6 / digital I/O |
| پین 11 | PAD05/AN5 — Analog input 5 / digital I/O |
| پین 12 | PAD04/AN4 — Analog input 4 / digital I/O |
| پین 13 | PAD03/AN3 — Analog input 3 / digital I/O |
| پین 14 | PAD02/AN2 — Analog input 2 / digital I/O |
| پین 15 | PAD01/AN1 — Analog input 1 / digital I/O |
| پین 16 | PAD00/AN0 — Analog input 0 / digital I/O |
| پین 17 | VDDA — Analog supply for ADC |
| پین 18 | VSSA — Analog ground for ADC |
| پین 19 | VDDX — External supply input (battery / 12V tolerant) |
| پین 20 | VSSX — External supply ground |
| پین 21 | VDDR — Internal 5V regulator output |
| پین 22 | VSSR — Internal regulator ground return |
| پین 23 | LIN — LIN 2.x physical layer transmit/receive |
| پین 24 | TXCAN — CAN transmit (if present) |
| پین 25 | RXCAN — CAN receive (if present) |
| پین 26 | BKGD/MS — Background Debug Mode / Mode Select |
| پین 27 | RESET — Reset input, active low |
| پین 28 | TEST — Factory test pin, tie to VDDR in normal operation |
| پین 29 | VDDF — Flash supply / core logic supply |
| پین 30 | VSSF — Flash / core logic ground |
| پین 31 | PP0 — GPIO port P0 / PWM output |
| پین 32 | PP1 — GPIO port P1 / PWM output |
| پین 33 | PP2 — GPIO port P2 / PWM output |
| پین 34 | PP3 — GPIO port P3 / PWM output |
| پین 35 | PP4 — GPIO port P4 / PWM output |
| پین 36 | PP5 — GPIO port P5 / PWM output |
| پین 37 | PS0 — GPIO port S0 / SPI / SCI |
| پین 38 | PS1 — GPIO port S1 / SPI / SCI |
| پین 39 | PS2 — GPIO port S2 / SPI / SCI |
| پین 40 | PS3 — GPIO port S3 / SPI / SCI |
| پین 41 | PS4 — GPIO port S4 / SPI / SCI |
| پین 42 | PS5 — GPIO port S5 / SPI / SCI |
| پین 43 | PS6 — GPIO port S6 / SPI / SCI |
| پین 44 | PS7 — GPIO port S7 / SPI / SCI |
| پین 45 | PT0 — GPIO port T0 / Timer channel |
| پین 46 | PT1 — GPIO port T1 / Timer channel |
| پین 47 | PT2 — GPIO port T2 / Timer channel |
| پین 48 | PT3 — GPIO port T3 / Timer channel |
کاربردهای معمول
S912ZVC96F0MLF مناسب است برای 6 کاربردs: Automotive HVAC Door Module, Automotive Seat Controller LIN Slave, Window Lift / Door Mirror Module, Body-Control LIN Slave Node, Instrument Cluster Auxiliary Circuit, Industrial Sensor / Metering Module.
Automotive HVAC Door Module
The S912ZVC96F0MLF is well-suited to automotive HVAC door modules where each actuator uses a small LIN-attached stepper or DC motor. The integrated LIN physical layer removes an external transceiver, the 32 MHz S12Z core comfortably handles PID control loops, and 96 KB Flash stores the LIN scheduler plus diagnostics. AEC-Q100 grade-1 qualification and -40 to +125C rating fit door-module thermal stress.
پیشنهادی
Automotive Seat Controller LIN Slave
Seat-control ECUs distribute power and LIN across multiple zone nodes, each running a small LIN slave. The S912ZVC96F0MLF's 8 KB RAM and 96 KB Flash allow seat-position memory tables plus fault logging, the 10-bit ADC reads back current sense, and the integrated regulator removes an external 5V LDO. AEC-Q100 grade-1 supports under-seat thermal conditions up to +125C.
پیشنهادی
Window Lift / Door Mirror Module
Window-lift and door-mirror modules require LIN communication, brush motor control, anti-pinch ADC sampling, and AEC-Q100 grade-1 qualification. The S912ZVC96F0MLF fits this profile with its integrated LIN and 5V regulator, 10-bit ADC for current-sense, and 96 KB Flash for anti-pinch algorithms. The 48-LQFP 7x7 package is small enough for placement inside mirror housings.
پیشنهادی
Body-Control LIN Slave Node
Body-control slaves (interior lighting, ambient trim, RLS sensor) typically attach to a central BCM via LIN and need a small, fully integrated MCU. The S912ZVC96F0MLF's integrated 5V regulator and LIN physical layer reduce the BOM to essentially the MCU plus bypass caps. 96 KB Flash allows node-local diagnostics plus CAN-to-LIN bridging when the BCM expects enriched telemetry.
پیشنهادی
Instrument Cluster Auxiliary Circuit
Auxiliary clusters and gauge-driver nodes often piggy-back on the instrument cluster and need a LIN-attached MCU for backlight, pointer, and indicator control. The S912ZVC96F0MLF provides PWM channels for backlight dimming plus LIN comms to the cluster MCU. The 32 MHz core handles cluster-fast pointer update loops while AEC-Q100 grade-1 supports dashboard thermal levels.
پیشنهادی
Industrial Sensor / Metering Module
Industrial LIN-attached flow, pressure, or heat meters benefit from the S912ZVC96F0MLF's 10-bit ADC (10 channels) for transducer readout and 96 KB Flash for calibration tables. The integrated LIN physical layer enables simple attachment to a host controller in metering cabinets. AEC-Q100 grade-1 also benefits outdoor enclosures with wider temperature swings than commercial-grade MCUs.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای S912ZVC96F0MLF — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | S912ZVCA19F0MLFR | S912ZVC12F0MLF | E912ZVC96F0MLF | S912ZVC64F0MLF |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 48-LQFP (7x7 mm) | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same |
| Core | S12Z 16-bit | S12Z 16-bit | S12Z 16-bit | S12Z 16-bit | S12Z 16-bit |
| Program Flash | 96 KB | 190 KB | 12 KB | 96 KB (extended screening) | 64 KB |
| RAM Size | 8 KB | 12 KB | 8 KB | 8 KB | 8 KB |
| Maximum Clock Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Integrated LIN Physical Layer | Yes (LIN 2.x) | Yes (LIN 2.x) | Yes (LIN 2.x) | Yes (LIN 2.x) | Yes (LIN 2.x) |
| Integrated 5V Regulator | Yes | Yes | Yes | Yes | Yes |
| Automotive Qualification (AEC-Q100) | Yes (Grade 1) | Yes (Grade 1) | Yes (Grade 1) | Yes (extended screening) | Yes (Grade 1) |
تفاوت‌های کلیدی
- MagniV integration eliminates external LIN transceiver + external 5V LDO (در مقابلS9S12G96F0VLFR)
- Higher memory headroom than S912ZVC12F0MLF (در مقابلS912ZVC12F0MLF)
- Verified pin-compatible upgrade to 190 KB Flash variant (در مقابلS912ZVCA19F0MLFR)
یادداشت‌های طراحی
The integrated 5V linear regulator (VDDR output) supplies the internal logic but cannot source significant current; decouple it with a 100 nF ceramic plus a 4.7 to 10 uF bulk capacitor placed within 10 mm of the pin. VDDX (battery/12V-tolerant input) still requires its own bulk capacitance and reverse-battery protection in the supply path. Always consult the NXP S12ZVC datasheet for the recommended external BOM.
Ensure the LIN bus load-pull resistance matches the LIN 2.x spec (typically 1 nF bus capacitance maximum). Do not connect a LIN node without the correct master/slave termination, and configure the device's internal LIN pull-up correctly during initialization. Pull-up of LIN to battery via external resistor is required only for the master node, not slaves.
The high-voltage analog input pins (PAD0-PAD15) tolerate 5V but not indefinite ESD; place TVS arrays near external connector pins. Use a star ground between VSSA (analog ground) and VSSX/VSSF (digital grounds) at a single point to keep ADC errors below 1 LSB. LQFP fine-pitch traces should be length-matched for parallel ADC sampling.
اطلاعات انطباق
AEC-Q100 grade-1 qualified per NXP MagniV family marketing; RoHS compliant per distributor listings; halogen-free status is not stated in the verified distributor data and is therefore unknown.
