SN74HC126D - 4-Channel 3-State Buffer | Texas Instruments
MPN: SN74HC126D ✓ فعالSN74HC126D نمای کلی
A 74HC-series tri-state buffer is a digital logic IC that transfers a logic signal while offering a high-impedance output condition. This places the device within the CMOS logic and bus-buffer hierarchy, where it supports communication between multiple drivers and a shared data bus. Unlike a conventional buffer that continuously drives its output, the SN74HC126D can be disconnected from the bus without introducing a logic level.
The SN74HC126D operates from 2 V to 6 V, allowing operation in both 3.3 V and 5 V systems. Its four non-inverting channels preserve the polarity of the input signals. The device can drive 15 LSTTL loads and is specified with a 7.8 mA output current, making it suitable for CMOS and mixed-logic bus interfaces. The low-power design also supports systems where supply efficiency and active current are important.
Each output enters the high-impedance state when its corresponding output-enable input is low. During normal operation, a high output-enable level permits the associated input to drive the output. Independent enable control makes it possible to isolate several buses independently, a useful feature in memory expansion, peripheral routing, bidirectional interface isolation, and test or debug systems.
Typical uses include data-bus buffering, microprocessor input and output ports, memory-module address lines, peripheral interface isolation, level-compatible CMOS logic systems, and control signals requiring a configurable high-impedance state. The 14-pin SOIC package is suitable for conventional PCB assembly, although SOIC-14 is larger than modern leadless packages.
Designers should account for enable timing and bus-contention risk. The output-enable inputs must not place two enabled drivers onto the same node unless their outputs are guaranteed not to conflict. Keep trace lengths short and maintain a continuous ground reference to limit switching noise. Use the manufacturer pin-description table and the pinout section of the SN74HC126 datasheet when assigning PCB nets.
This page organizes the SN74HC126D specifications, verified drop-in alternatives, package details, comparison data, and practical design guidance into one engineering reference. It also highlights the distinction between independent 3-state control, wide-voltage CMOS operation, bus-drive capability, and the constraints that must be evaluated before substitution.
جایگزینهای drop-in برای SN74HC126D — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
74HC126D,653
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
74HC126D
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
SN74HC126D حداکثر مقادیر مجاز و مشخصات الکتریکی
| Number of Channels | 4 channels |
| Logic Type | Non-inverting |
| Output State | 3-state |
| Supply Voltage Range | 2 V to 6 V |
| Nominal Supply Voltage | 5 V |
| Technology | CMOS |
| محدوده دمای کاری | -40 °C to +85 °C |
| بستهبندی | 14-pin SOIC |
| Output Current | 7.8 mA |
| LSTTL Load Capability | 15 loads |
| جریان سکون | 80 µA |
| Device Function | Quad buffer/line driver |
| Enable Control | Independent output enable per channel |
| Output Disable Condition | Output-enable input low |
| وضعیت RoHS | unknown |
راهنمای پیکربندی پین SN74HC126D 14-pin soic
پیکربندی پین برای SN74HC126D (پکیج 14-pin soic). این IC دیجیتال شامل GPIO، رابطهای ارتباطی (UART، SPI، I2C) و پینهای تغذیه است. برای عملکردهای جایگزین پین و گزینههای پیکربندی به دیتاشیت سازنده مراجعه کنید. ضروری برای طراحی سیستمهای نهفته و چیدمان PCB.
داده پینآوت تفصیلی موجود نیست برای SN74HC126D.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
SN74HC126D مناسب است برای 6 کاربردs: Shared Data-Bus Buffering, Microprocessor Port Isolation, Memory Address-Line Routing, Peripheral Interface Isolation, Control-Signal Bus, Test and Debug Signal Routing.
Shared Data-Bus Buffering
The SN74HC126D fits shared data-bus architectures because it provides four non-inverting buffers with independent 3-state outputs. Each channel can drive a logic node while the others are isolated, preventing permanently connected output drivers from loading the bus. Its 2 V to 6 V supply range supports both 3.3 V and 5 V systems, while the 7.8 mA output-current rating and 15-LSTTL-load capability provide useful drive margin for CMOS and mixed-logic receivers. The design should assert only one output-enable driver for a contested node at a time and verify timing during enable transitions.
پیشنهادی
Microprocessor Port Isolation
SN74HC126D can isolate selected microprocessor or microcontroller port signals when a peripheral interface must be electrically disconnected during reset or mode changes. The four independent output-enable inputs let the controller release individual outputs to high impedance while preserving signal polarity. Its 2 V to 6 V operating range accommodates embedded systems operating at 3.3 V or 5 V, and the 14-pin SOIC package is straightforward to route on conventional through-hole-style PCB footprints. Control the enable pins from a controller that cannot back-drive an active output, and verify the interface timing against the connected device.
پیشنهادی
Memory Address-Line Routing
The SN74HC126D is suitable for memory address-line routing where several address sources must connect to one bus at different times. Its 14-pin SOIC package contains four non-inverting tri-state channels, allowing two complete address pairs to be isolated independently. Operating from 2 V to 6 V supports legacy 5 V logic as well as 3.3 V systems, while the specified 7.8 mA output current provides drive for CMOS and LSTTL-compatible loads. Confirm that enable transitions occur outside the memory's setup and hold windows and that the connected bus never has two outputs enabled simultaneously.
پیشنهادی
Peripheral Interface Isolation
SN74HC126D provides selectable isolation between a host controller and peripheral circuitry by placing a non-inverting buffer and high-impedance output stage in each path. This prevents a peripheral bus driver from fighting the host during reset, firmware handoff, or test modes. The 2 V to 6 V range supports mixed system rails, while the four independent enables allow different peripheral channels to be connected or released separately. Route output-enable controls so all potentially conflicting drivers share a deterministic startup sequence, and check propagation delay and bus setup timing in the final interface design.
پیشنهادی
Control-Signal Bus
The SN74HC126D can buffer multiple active-high control signals that are distributed to different logic blocks and sometimes share a common conductor. Its non-inverting channels preserve control polarity, and each output can be disconnected with its own output-enable input. The device operates at 2 V to 6 V, making it suitable for 3.3 V and 5 V control architectures, with a documented output current of 7.8 mA. For shared control lines, enforce mutually exclusive enable states and account for the propagation delay before an enabled output is expected to change state.
پیشنهادی
Test and Debug Signal Routing
SN74HC126D is useful in test and debug circuitry where diagnostic outputs must connect to a shared bus only during a specific measurement or debug interval. The four independently enabled outputs let the design isolate inactive test drivers and prevent bus contention. Its non-inverting logic avoids adding unintended polarity changes to the monitored signals, and the 2 V to 6 V supply range supports common industrial, communications, and embedded test platforms. Use defined pull resistors on disabled buses where required, and check the enable sequencing against instrument or debugger acquisition timing.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای SN74HC126D — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | 74HC126D,653 | 74HC126D |
|---|---|---|---|
| Brand | Texas Instruments | Nexperia | NXP Semiconductors |
| Package | 14-SOIC | 14-SOIC - same | 14-SOIC - same |
| Number of Channels | 4 channels | 4 channels | 4 channels |
| Logic Polarity | Non-inverting | Non-inverting | Non-inverting |
| Output State | 3-state | 3-state | 3-state |
| Supply Voltage Range | 2 V to 6 V | 2 V to 6 V | 2 V to 6 V |
| Output Current | 7.8 mA | 7.8 mA | 7.8 mA |
| LSTTL Load Capability | 15 loads | 15 loads | 15 loads |
| Technology | CMOS | CMOS | CMOS |
تفاوتهای کلیدی
- Directly preserves non-inverting bus logic (در مقابل74HC125)
- Matches the 74HC126D pin and drive characteristics (در مقابل74HC126D,653)
- Matches the documented 74HC126 family topology (در مقابل74HC126D)
یادداشتهای طراحی
Do not enable two SN74HC126D outputs that drive the same node at the same time. Although every channel has an independent output-enable input and can enter a high-impedance state, overlapping enable timing can produce current contention and an indeterminate logic level. Define a single arbitration source for shared buses and verify that every mode change satisfies the timing requirements of the connected device.
Place the device so the four data paths remain short and maintain a continuous ground plane beneath and around the SOIC-14 footprint. Connect decoupling directly to the supply and ground pins with minimal loop area, and route output-enable traces away from sensitive data lines. The wide 2 V to 6 V supply range does not remove the need for stable local bypassing, especially when the buffer drives longer PCB traces or capacitive bus nodes.
Size the supply network for both the 74HC quiescent current and the enabled-channel output current. The documented low-power operating characteristic of approximately 80 µA applies to the low-power behavior of the device, while enabled outputs can draw up to 7.8 mA under the stated conditions. Check worst-case static and switching demand rather than sizing the rail from quiescent current alone.
اطلاعات انطباق
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status is stated for the exact SN74HC126D ordering code.