Texas Instruments

SN74HC126D - 4-Channel 3-State Buffer | Texas Instruments

MPN: SN74HC126D ✓ Hoạt động
2 V to 6 V Vdss 7.8 mA Id 14-pin SOIC Package
MOQ: 1 |

SN74HC126D Tóm tắt

The Texas Instruments SN74HC126D is a quad, non-inverting CMOS buffer and line driver with independent 3-state outputs, a 2 V to 6 V operating supply range, and a 14-pin SOIC package. Each of its four channels provides a high-impedance output state for shared-bus isolation, while the associated output-enable input controls the corresponding buffer independently.

A 74HC-series tri-state buffer is a digital logic IC that transfers a logic signal while offering a high-impedance output condition. This places the device within the CMOS logic and bus-buffer hierarchy, where it supports communication between multiple drivers and a shared data bus. Unlike a conventional buffer that continuously drives its output, the SN74HC126D can be disconnected from the bus without introducing a logic level.

The SN74HC126D operates from 2 V to 6 V, allowing operation in both 3.3 V and 5 V systems. Its four non-inverting channels preserve the polarity of the input signals. The device can drive 15 LSTTL loads and is specified with a 7.8 mA output current, making it suitable for CMOS and mixed-logic bus interfaces. The low-power design also supports systems where supply efficiency and active current are important.

Each output enters the high-impedance state when its corresponding output-enable input is low. During normal operation, a high output-enable level permits the associated input to drive the output. Independent enable control makes it possible to isolate several buses independently, a useful feature in memory expansion, peripheral routing, bidirectional interface isolation, and test or debug systems.

Typical uses include data-bus buffering, microprocessor input and output ports, memory-module address lines, peripheral interface isolation, level-compatible CMOS logic systems, and control signals requiring a configurable high-impedance state. The 14-pin SOIC package is suitable for conventional PCB assembly, although SOIC-14 is larger than modern leadless packages.

Designers should account for enable timing and bus-contention risk. The output-enable inputs must not place two enabled drivers onto the same node unless their outputs are guaranteed not to conflict. Keep trace lengths short and maintain a continuous ground reference to limit switching noise. Use the manufacturer pin-description table and the pinout section of the SN74HC126 datasheet when assigning PCB nets.

This page organizes the SN74HC126D specifications, verified drop-in alternatives, package details, comparison data, and practical design guidance into one engineering reference. It also highlights the distinction between independent 3-state control, wide-voltage CMOS operation, bus-drive capability, and the constraints that must be evaluated before substitution.

Bộ thay thế dễ dàng lắp đặt cho SN74HC126D — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

74HC126D,653

✅ Drop-In
📦 14-SOIC
Same four non-inverting 3-state channels and 14-SOIC footprint; output current is 7.8 mA versus 7.8 mA, a 0% difference

📋 Tham chiếu thay thế (không có trong danh mục)

74HC126D

✅ Drop-In
📦 14-SOIC
Same four non-inverting 3-state channels and 14-SOIC footprint; documented output current is 7.8 mA versus 7.8 mA, a 0% difference

📋 Tham chiếu thay thế (không có trong danh mục)

SN74HC126D Tỷ lệ tối đa & tính chất điện

Number of Channels 4 channels
Logic Type Non-inverting
Output State 3-state
Supply Voltage Range 2 V to 6 V
Nominal Supply Voltage 5 V
Technology CMOS
Khoảng nhiệt độ hoạt động -40 °C to +85 °C
Hộp 14-pin SOIC
Output Current 7.8 mA
LSTTL Load Capability 15 loads
Điện áp yên tĩnh 80 µA
Device Function Quad buffer/line driver
Enable Control Independent output enable per channel
Output Disable Condition Output-enable input low
Trạng thái RoHS unknown

Hướng dẫn cấu hình chân SN74HC126D 14-pin soic

Cấu hình chân cho SN74HC126D (14-pin soic gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.

Bảng cấu hình chân 14-pin soic cho SN74HC126D

Không có dữ liệu chân cụ thể sẵn có cho SN74HC126D.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

SN74HC126D phù hợp cho 6 Áp dụngs: Shared Data-Bus Buffering, Microprocessor Port Isolation, Memory Address-Line Routing, Peripheral Interface Isolation, Control-Signal Bus, Test and Debug Signal Routing.

🖥️

Shared Data-Bus Buffering

The SN74HC126D fits shared data-bus architectures because it provides four non-inverting buffers with independent 3-state outputs. Each channel can drive a logic node while the others are isolated, preventing permanently connected output drivers from loading the bus. Its 2 V to 6 V supply range supports both 3.3 V and 5 V systems, while the 7.8 mA output-current rating and 15-LSTTL-load capability provide useful drive margin for CMOS and mixed-logic receivers. The design should assert only one output-enable driver for a contested node at a time and verify timing during enable transitions.

🧩

Microprocessor Port Isolation

SN74HC126D can isolate selected microprocessor or microcontroller port signals when a peripheral interface must be electrically disconnected during reset or mode changes. The four independent output-enable inputs let the controller release individual outputs to high impedance while preserving signal polarity. Its 2 V to 6 V operating range accommodates embedded systems operating at 3.3 V or 5 V, and the 14-pin SOIC package is straightforward to route on conventional through-hole-style PCB footprints. Control the enable pins from a controller that cannot back-drive an active output, and verify the interface timing against the connected device.

⚡

Memory Address-Line Routing

The SN74HC126D is suitable for memory address-line routing where several address sources must connect to one bus at different times. Its 14-pin SOIC package contains four non-inverting tri-state channels, allowing two complete address pairs to be isolated independently. Operating from 2 V to 6 V supports legacy 5 V logic as well as 3.3 V systems, while the specified 7.8 mA output current provides drive for CMOS and LSTTL-compatible loads. Confirm that enable transitions occur outside the memory's setup and hold windows and that the connected bus never has two outputs enabled simultaneously.

🏭

Peripheral Interface Isolation

SN74HC126D provides selectable isolation between a host controller and peripheral circuitry by placing a non-inverting buffer and high-impedance output stage in each path. This prevents a peripheral bus driver from fighting the host during reset, firmware handoff, or test modes. The 2 V to 6 V range supports mixed system rails, while the four independent enables allow different peripheral channels to be connected or released separately. Route output-enable controls so all potentially conflicting drivers share a deterministic startup sequence, and check propagation delay and bus setup timing in the final interface design.

🔧

Control-Signal Bus

The SN74HC126D can buffer multiple active-high control signals that are distributed to different logic blocks and sometimes share a common conductor. Its non-inverting channels preserve control polarity, and each output can be disconnected with its own output-enable input. The device operates at 2 V to 6 V, making it suitable for 3.3 V and 5 V control architectures, with a documented output current of 7.8 mA. For shared control lines, enforce mutually exclusive enable states and account for the propagation delay before an enabled output is expected to change state.

🖥️

Test and Debug Signal Routing

SN74HC126D is useful in test and debug circuitry where diagnostic outputs must connect to a shared bus only during a specific measurement or debug interval. The four independently enabled outputs let the design isolate inactive test drivers and prevent bus contention. Its non-inverting logic avoids adding unintended polarity changes to the monitored signals, and the 2 V to 6 V supply range supports common industrial, communications, and embedded test platforms. Use defined pull resistors on disabled buses where required, and check the enable sequencing against instrument or debugger acquisition timing.

Tóm tắt các sản phẩm được đề xuất

74HC126D,653 Drop-in 3-state bus-buffer alternative Được sử dụng trong: Shared Data-Bus Buffering, Microprocessor Port Isolation, Memory Address-Line Routing, Peripheral Interface Isolation, Control-Signal Bus, Test and Debug Signal Routing 74HC126D Equivalent 74HC bus-buffer device Được sử dụng trong: Shared Data-Bus Buffering, Memory Address-Line Routing, Peripheral Interface Isolation, Control-Signal Bus, Test and Debug Signal Routing SN74HC126D Texas Instruments Được sử dụng trong: Microprocessor Port Isolation
What is the SN74HC126D and what does it do?
The SN74HC126D is a Texas Instruments quad, non-inverting CMOS buffer with independent 3-state outputs. It contains four one-bit buffer channels, operates from 2 V to 6 V, and comes in a 14-pin SOIC package. According to the manufacturer datasheet, each output becomes high impedance when its associated output-enable input is low, allowing several buffered devices to share a bus without permanent contention.
What is the operating voltage range of SN74HC126D?
The SN74HC126D operates from 2 V to 6 V, supporting both 3.3 V and 5 V CMOS logic systems. According to the Texas Instruments SN74HC126 datasheet, the device is a 74HC-series buffer/line driver with independent 3-state outputs. Its wide supply range also permits mixed-voltage interface designs when signal levels and timing requirements remain compatible.
Where can I download the SN74HC126D datasheet PDF?
The official SN74HC126D datasheet PDF is available from the Texas Instruments product document at https://www.ti.com/lit/ds/symlink/sn74hc126.pdf. The document contains the complete device description, logic diagram, electrical characteristics, switching characteristics, recommended operating conditions, and package pin assignments. Use the pin-description table in that manufacturer document when assigning SOIC-14 PCB nets.
How does the 3-state output on SN74HC126D work?
Each SN74HC126D output is driven when its output-enable input is high and enters the high-impedance state when that input is low. According to the Texas Instruments datasheet, the four channels have independent output-enable control. This permits selective bus participation, but two simultaneously enabled outputs must never be connected to the same node unless their drive states are guaranteed compatible.
Is SN74HC126D suitable for a 3.3 V system?
Yes, the SN74HC126D is suitable for a 3.3 V system because its specified operating supply range is 2 V to 6 V. According to the manufacturer datasheet, the device is based on 74HC CMOS logic and provides four non-inverting tri-state buffers. Confirm the associated data and control signals remain within the input and output limits at the actual supply voltage and temperature.
What can replace the SN74HC126D?
The Nexperia 74HC126D,653 is a direct replacement candidate because it provides the same four non-inverting 3-state channels in a 14-SO package. The Nexperia 74HC126D is also a functionally equivalent 14-SOIC option from the documented 74HC126 family. According to the cross-reference information, the devices maintain consistent terminal assignments and electrical functions, but production approval should still confirm timing, qualification, and lifecycle requirements.
Is SN74HC126D the same as 74HC126D?
SN74HC126D and 74HC126D describe the same fundamental quad, non-inverting 3-state buffer function, but the exact ordering code can identify a particular manufacturer. The comparison information identifies 74HC126D as equivalent to SN74HC126D in topology and pin arrangement. For a production substitution, confirm the complete manufacturer part number, package drawing, lifecycle status, temperature range, and electrical limits before releasing the change.
What are the key specifications engineers should know about SN74HC126D?
The key SN74HC126D specifications are four non-inverting channels, independent 3-state outputs, a 2 V to 6 V supply range, and a 14-pin SOIC package. According to the Texas Instruments datasheet, the output drive capability reaches 7.8 mA and 15 LSTTL loads. The operating temperature range is -40 °C to +85 °C, making the device suitable for common industrial and commercial logic environments.
How much current can the SN74HC126D output drive?
The SN74HC126D is specified for 7.8 mA output current and can directly drive up to 15 LSTTL loads. According to the Texas Instruments SN74HC126 datasheet, the maximum capacitive load must remain within the value stated in the switching-characteristics table. Actual usable drive also depends on supply voltage, output state, bus capacitance, trace length, and the switching rate of the connected network.
When should I choose SN74HC126D over a 74HC125?
Choose SN74HC126D when the design needs four non-inverting tri-state bus buffers, while a 74HC125 provides four independent inverting buffers. Both devices use active-high output-enable control and support high-impedance bus isolation. The distinction matters because the SN74HC126D preserves signal polarity, so no additional inversion is needed after the buffer stage. Verify package, timing, and logic polarity during final selection.
Where can I find the SN74HC126D pinout?
The SN74HC126D pinout is in the pin-configuration section of the official Texas Instruments datasheet at https://www.ti.com/lit/ds/symlink/sn74hc126.pdf. The device uses a 14-pin SOIC outline with four data inputs, four outputs, four output-enable inputs, a supply input, and ground. Follow the manufacturer pin-description table when assigning tracks because the exposed package dimensions and numbering must match the selected footprint.
What is the best Nexperia equivalent for SN74HC126D?
The Nexperia 74HC126D,653 is the clearest Nexperia equivalent because it is identified as a quad, non-inverting, 3-state buffer in a 14-SO package. Cross-reference information reports consistent terminals, package, and functional characteristics. According to the Nexperia and Texas Instruments device descriptions, both devices provide four independently enabled outputs, but engineers should verify production qualifications and timing margins before substitution.
Where can I buy SN74HC126D and check its lead time?
Use the Request a Quote form on this page to ask about SN74HC126D availability, unit pricing, minimum order quantity, and current lead time. The manufacturer lists the SN74HC126 family as a 2 V to 6 V, four-channel 3-state buffer product, and the target ordering code uses the 14-pin SOIC package. Confirm the requested quantity, assembly packaging, and shipment destination when submitting the quote request.
Is SN74HC126D in stock?
Current SN74HC126D inventory should be confirmed through the Request a Quote form on this page. The Request a Quote workflow provides current stock, allocation, and lead-time information for the exact ordering code and requested quantity. Inventory can vary by package and shipment quantity, so use the form rather than relying on a generic family-level stock indication.
What is the price of SN74HC126D?
The current unit price for SN74HC126D is returned through the Request a Quote form on this page. Submit the required quantity and any reel, tray, or other assembly preferences so the quote reflects the exact source and quantity conditions. The device is the 14-pin SOIC version of Texas Instruments' four-channel, non-inverting 3-state 74HC buffer.
Can two SN74HC126D outputs drive the same bus?
Two SN74HC126D outputs may share a bus only when their output-enable controls guarantee that no conflicting drivers are active simultaneously. According to the manufacturer datasheet, a low output-enable input places the corresponding output in a high-impedance state. Use all required enable pins so only one buffer drives a given node, and include suitable pull resistors where the system requires a defined state during reset or power transitions.
What is the lead time for SN74HC126D?
Request the current SN74HC126D lead time through the Request a Quote form on this page and include your required quantity and shipment destination. Lead time can vary with order quantity, package configuration, and production scheduling. The part is specified as a 14-pin SOIC, four-channel CMOS tri-state buffer with a 2 V to 6 V supply range, so no electrical qualification change is needed for the standard configuration.

Dữ liệu tham khảo kỹ thuật cho SN74HC126D — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose SN74HC126D for shared-bus or interface-isolation designs that require four non-inverting buffers with independent high-impedance output states. Its 2 V to 6 V operating range supports both 3.3 V and 5 V logic, while the 7.8 mA output-current specification and 15-LSTTL-load capability suit conventional CMOS and mixed-logic interfaces. The Nexperia 74HC126D,653 is a strong drop-in candidate when procurement needs a second source and its production, qualification, and lifecycle requirements meet the project standard. The NXP 74HC126D provides the same documented topology and package, but it should be checked against the exact electrical and timing limits used by the design. Use a 74HC125 instead only when inverted output polarity is intentional. Before releasing any substitute, verify pin assignments, propagation timing, enable requirements, temperature range, package dimensions, and availability.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này 74HC126D,653 74HC126D
Brand Texas Instruments Nexperia NXP Semiconductors
Package 14-SOIC 14-SOIC - same 14-SOIC - same
Number of Channels 4 channels 4 channels 4 channels
Logic Polarity Non-inverting Non-inverting Non-inverting
Output State 3-state 3-state 3-state
Supply Voltage Range 2 V to 6 V 2 V to 6 V 2 V to 6 V
Output Current 7.8 mA 7.8 mA 7.8 mA
LSTTL Load Capability 15 loads 15 loads 15 loads
Technology CMOS CMOS CMOS

Bảo phân biệt quan trọng

  • Directly preserves non-inverting bus logic (vs74HC125)
  • Matches the 74HC126D pin and drive characteristics (vs74HC126D,653)
  • Matches the documented 74HC126 family topology (vs74HC126D)

Ghi chú thiết kế

Do not enable two SN74HC126D outputs that drive the same node at the same time. Although every channel has an independent output-enable input and can enter a high-impedance state, overlapping enable timing can produce current contention and an indeterminate logic level. Define a single arbitration source for shared buses and verify that every mode change satisfies the timing requirements of the connected device.

Place the device so the four data paths remain short and maintain a continuous ground plane beneath and around the SOIC-14 footprint. Connect decoupling directly to the supply and ground pins with minimal loop area, and route output-enable traces away from sensitive data lines. The wide 2 V to 6 V supply range does not remove the need for stable local bypassing, especially when the buffer drives longer PCB traces or capacitive bus nodes.

Size the supply network for both the 74HC quiescent current and the enabled-channel output current. The documented low-power operating characteristic of approximately 80 µA applies to the low-power behavior of the device, while enabled outputs can draw up to 7.8 mA under the stated conditions. Check worst-case static and switching demand rather than sizing the rail from quiescent current alone.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status is stated for the exact SN74HC126D ordering code.

Dữ liệu được xác minh vào: 2026-11-14 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

SN74HC126D datasheet SN74HC126D pinout SN74HC126D datasheet pdf SN74HC126D equivalent SN74HC126D replacement SN74HC126D cross reference SN74HC126D price SN74HC126D stock Texas Instruments SN74HC126D SN74HC126D 14-SOIC buffer SN74HC126D 2V 6V SN74HC126D 3-state output SN74HC126D vs 74HC126D SN74HC126D bus buffer application

Các bộ phận và thuật ngữ liên quan

Texas Instruments SN74HC126D SN74HC126 74HC126D,653 Nexperia 74HC126D NXP Semiconductors 74HC126 74HC125 quad buffer line driver tri-state buffer 3-state output non-inverting logic CMOS logic bus buffer high-impedance output output enable SOIC-14 logic IC semiconductor shared data bus peripheral isolation memory address routing output current
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ